- Home
- 1069608581
- Instructions
1069608581 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water was running into refrig from freezer and ice cream was soft
-
William from Delano, MN
- Really Easy
- Less than 15 mins
-
Nutdriver
We wasted time looking for the electrical schematic on our refrigerator (the first step in the instructions). By skipping that and reading further in the instructions, the type of cooling that the refrigerator has can easily be determined by the colors of the wires that go to the defrost timer. You need to know this to set up the timer
... Read more
properly for your specific refrigerator. Had I just started there, the entire repair would have taken less than 10 minutes. Very simple repair and it works like a charm, no more water coming into the refrigerator and the ice cream is rock hard. Glad we didn't have to spend lots on a new appliance. Thanks Part Select.com! BH
Read less
Was this helpful?
Thank you for voting!
frosted evaperator
-
Burton from Mount ShaSTA, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
I was a Sears repair man for fourty eight years , so I don"t think I should say how easy this was.
Was this helpful?
Thank you for voting!
Switch didn't work
-
Don from Laramie, WY
- Easy
- 15 - 30 mins
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00
Was this helpful?
Thank you for voting!
Protective cover for bulb had melted
-
Lee from Brooklyn, NY
- Very Difficult
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent i
... Read more
tems in the fridge from being able to touch. Bad solution.
Read less
Was this helpful?
Thank you for voting!
fresh food side not getting cold
-
Garry from Sayville, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver
I wasnt about to call Mr Appliance of Bayport NY the last time I called him I got a bill for $72.00 and he told me I needed a new frig. So I paid him then the next day I went to parts select and fixed it myself for about $50.00 But this time it was my Moms frig and the frig side (fresh food side) wasnt getting cold So again I went to part
... Read more
s select and put in a bimetel thermostat and it works perfect now. Im sure I saved a lot of $ and thanks to parts select, They helped me diagnose the problem and make the repair step by step! EASY! Thanks parts select...Garry from long island NY
Read less
Was this helpful?
Thank you for voting!
Evaporator motor squeal.
-
Steven from Hilliard, OH
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
After finding an almost obsolete part( thanks PartSelect!) the installation was rather easy. Remove the back panel of the freezer and vent with a screwdriver and a nut driver. Disconnect the three wires, green, white and red.Remove motor from mounting and replace with new motor. I had to make a slight adjustment to the ground wire on the
... Read more
new motor that required adjusting the position of the contact-no big deal. The motor fit perfectly. Popped fan on and assembled. 20 minutes max.
Read less
Was this helpful?
Thank you for voting!
rReally Noisy Fan
-
Robert from Sierra Vista, AZ
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
1. Unplug Refrigerator 2. Remove inside back freezer panel. (4 Screws) 3. Remove Duct Cover (3 Screws). 4. Cut electrical connections to fan. 5. Remove Old Fan motor (2 hex screws. 6. Install ground wire (was not one there previously). 7. Put slide-on electrical connectors on remaining 2 motor wires. (Were not any on original unit.) 8. R
... Read more
eplace Fan Motor (Don't forget the rubber vibration pads) 9. Reconnect electrical wires. 10. Press on plastic fan blade. 11. Plug in refrigerator to test install. It works. 12 Unplug refrigerator and replace ducting and back panel to freezer. Plug it back in. Voila, Quiet again.
Read less
Was this helpful?
Thank you for voting!
no problems at at all
-
Eliseo from Pleasanton, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
removed rear wall panel took off old fan motor disconnected motor. Installed new grommets re-installed motor inserted new fan. Didn't have to trim fan re-connected wires and rear panel and reconnected power. no problems...
Was this helpful?
Thank you for voting!
Repalce evaporator fan
-
William from Ledyard, CT
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
The evaporator fan is located in the freezer behind the back wall. If you have the ice maker remove it first then remove the screws on the top of the panel. You will notice the side brackets for the top shelf will make it hard to remve the panal but by slitly binding the center the panal came right out. The fan is held in a bracke tha co
... Read more
mes right out. The wire unplu right from the fan so do not try to unplg the seal plug to the left side. Swap the fan with the new one useing the new rubber monts re-connect the wires and reasymble. Put the bottom of the back panal in first then work each side in past the shelf bracket binding the center slightly.
Read less
Was this helpful?
Thank you for voting!
Both the freezer and bottom of refrig too hot
-
Marcia from Kansas, OK
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Was very simple once I found out where the defrost timer was located. I had a friend walking me through trying to find the location on the phone. Not all models have them in the same place. Once the part was located all I had to do was remove the cover, unplug the old one and plug the new one in just the way the old one came off. The blac
... Read more
k wire was easy to locate on the old and just matched it up. Put the cover back on and plugged it in. It was no time till I started feeling it cool. Checked both top and bottom with thermomater and it was where it should be within 12 hours. I am happy and using it again. Was almost ready to throw it out. Did not know it was so cheap to fix one. Nothing anyone can't handle. If this woman can do it anyone can.
Read less
Was this helpful?
Thank you for voting!
Freezer was too cold and refrigerator was too warm
-
Jolinda from Eau Claire, WI
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
After receiving the part, I watched the installation video on the PartSelect website. The step by step demonstration was excellent. I felt confident I could do it myself after watching the video just once, and utilizing the written instructions that came with the part. The installation went smoothly, and my refrigerator is functioning
... Read more
correctly again. Best of all, I did not have to go through the hassle and expense of hiring a repair person!
Read less
Was this helpful?
Thank you for voting!
Broke the arm off the food compartment rocker switch
-
David from St. Pete Beach, FL
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips
... Read more
were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Read less
Was this helpful?
Thank you for voting!
Tray had rusted out, leaking!
-
Linda from Wilson, NC
- Really Easy
- 15 - 30 mins
-
Wrench set
Removed the screw from the old tray. Attached the new tray and return the screw using a wrench to assure the screw was torqued properly.
Was this helpful?
Thank you for voting!
How to get timer out of defrost cycle?
-
David from Virginia Beach, VA
- A Bit Difficult
- 15 - 30 mins
-
Socket set
Talked to local appliance repair tech, who explained how to manually turn timer with a screw driver and listen to the switch go from on to off.
Was this helpful?
Thank you for voting!
Noisy fan
-
Harry from Cincinnati, OH
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Unplug the refrigerator. Remove the rear shelf supports by lifting them straight up. No tools required. Remove the screws holding the rear cover of the freezer. Use a nut driver to remove the 4 screws holding the fan housing. Unplug the wiring harness, then remove the fan and install the new one. Remount the housing, plug in the har
... Read more
ness replace the rear cover, install the shelf supports and plug in the refrigerator. It was 30 minutes start to finish, which includes the time to gather the tools, unload and reload the freezer, and putting the tolls away!
Read less
Was this helpful?
Thank you for voting!