- Home
- 1069608281
- Instructions
1069608281 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
See below
-
Patricia from Hobe Sound, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
The defrost timer that I ordered form you did the trick. My fridge was
running all the time and the fridge temp was 55 but the freezer was 10
below. The instructions did not say how to test the old one to compare with
the new on. However in the Readers Digest Home Repair book it did and the
test proved that it was defe ... Read more ctive. Your article said that with the system I
had, 65% on the time it was the timer. I ordered it and thank you it works
just fine. I do have another problem, maybe you can help. The fridge runs
for 6 minuets and stays off for 10 minuets. The temp in the freezer is 0
and the fridge is 35-40 on the warmest settings, but all is well.
Thank you
running all the time and the fridge temp was 55 but the freezer was 10
below. The instructions did not say how to test the old one to compare with
the new on. However in the Readers Digest Home Repair book it did and the
test proved that it was defe ... Read more ctive. Your article said that with the system I
had, 65% on the time it was the timer. I ordered it and thank you it works
just fine. I do have another problem, maybe you can help. The fridge runs
for 6 minuets and stays off for 10 minuets. The temp in the freezer is 0
and the fridge is 35-40 on the warmest settings, but all is well.
Thank you
Read less
Was this helpful?
Thank you for voting!
Freezer was too cold and refrigerator was too warm
-
Jolinda from Eau Claire, WI
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
After receiving the part, I watched the installation video on the PartSelect website. The step by step demonstration was excellent. I felt confident I could do it myself after watching the video just once, and utilizing the written instructions that came with the part. The installation went smoothly, and my refrigerator is functioning
... Read more
correctly again. Best of all, I did not have to go through the hassle and expense of hiring a repair person!
Read less
Was this helpful?
Thank you for voting!
Broke the arm off the food compartment rocker switch
-
David from St. Pete Beach, FL
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips
... Read more
were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Read less
Was this helpful?
Thank you for voting!
Evaporator motor squeal.
-
Steven from Hilliard, OH
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
After finding an almost obsolete part( thanks PartSelect!) the installation was rather easy. Remove the back panel of the freezer and vent with a screwdriver and a nut driver. Disconnect the three wires, green, white and red.Remove motor from mounting and replace with new motor. I had to make a slight adjustment to the ground wire on the
... Read more
new motor that required adjusting the position of the contact-no big deal. The motor fit perfectly. Popped fan on and assembled. 20 minutes max.
Read less
Was this helpful?
Thank you for voting!
Both the freezer and bottom of refrig too hot
-
Marcia from Kansas, OK
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Was very simple once I found out where the defrost timer was located. I had a friend walking me through trying to find the location on the phone. Not all models have them in the same place. Once the part was located all I had to do was remove the cover, unplug the old one and plug the new one in just the way the old one came off. The blac
... Read more
k wire was easy to locate on the old and just matched it up. Put the cover back on and plugged it in. It was no time till I started feeling it cool. Checked both top and bottom with thermomater and it was where it should be within 12 hours. I am happy and using it again. Was almost ready to throw it out. Did not know it was so cheap to fix one. Nothing anyone can't handle. If this woman can do it anyone can.
Read less
Was this helpful?
Thank you for voting!
Switch didn't work
-
Don from Laramie, WY
- Easy
- 15 - 30 mins
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00
Was this helpful?
Thank you for voting!
Noisy fan
-
Harry from Cincinnati, OH
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Unplug the refrigerator. Remove the rear shelf supports by lifting them straight up. No tools required. Remove the screws holding the rear cover of the freezer. Use a nut driver to remove the 4 screws holding the fan housing. Unplug the wiring harness, then remove the fan and install the new one. Remount the housing, plug in the har
... Read more
ness replace the rear cover, install the shelf supports and plug in the refrigerator. It was 30 minutes start to finish, which includes the time to gather the tools, unload and reload the freezer, and putting the tolls away!
Read less
Was this helpful?
Thank you for voting!
Refrigerator not cooling
-
Bryan from Midland, NC
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
Exactly how the part select video described it. Threw a little curve ball figuring out which timer setting to set it to. But the instructions provided with defrost timer walked me right through it. No problem. After installing part nothing happened for about ten minutes, which had me second guessing each and every step. Then, like magic,
... Read more
cold air began blowing. What a relief. Thanks so much, love this site. Refrigerator works like new!
Read less
Was this helpful?
Thank you for voting!
frosted evaperator
-
Burton from Mount ShaSTA, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
I was a Sears repair man for fourty eight years , so I don"t think I should say how easy this was.
Was this helpful?
Thank you for voting!
Evaporator Would Freeze Up And The Food Section Could'nt Cool
-
michael from buchanan, TN
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
I just followed the enclosed instructions
Was this helpful?
Thank you for voting!
fan motor did not run all the time
-
Charles from Marion, IN
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
unpluged refrigerator. removed panel in front of fan. Removed the fan motor. Installed the new fan kit. Replaced the panel in front of fan. Pluged the refrigerator back in. The refrigerator runs a 100 percent better
Was this helpful?
Thank you for voting!
not cooling
-
Ted from Crestline, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
R/R part, 3 screws reconnect 3 wires. easy.
Was this helpful?
Thank you for voting!
freeser and cooler they wasnt work and it won't start
-
PATRICIO from CHARLOTTE, NC
- Really Easy
- Less than 15 mins
-
Screw drivers
First thing, I didn't have any idea how to fix my refrigerator, but I saw some videos on line, I just pull the start relay, it sound like little parts inside. I order to PART SELECT my Start Relay combination and part select have more comments, diagrams it was easy to find the part. Put the new start relay was easy, I just conect those wi
... Read more
res back it took less than 10 minutes and it's working now.thanks to Part Select to make easy to fix it.
Read less
Was this helpful?
Thank you for voting!
light would come on and off
-
Dora from Rock Island, IL
- Really Easy
- Less than 15 mins
Viewed the viedo - it showed what to do
Was this helpful?
Thank you for voting!
No Light
-
Mary from Jefferson Township, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.
Was this helpful?
Thank you for voting!