1069600515 Kenmore Refrigerator - Instructions

All Instructions for the 1069600515
91 - 105 of 304

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator quit cooling and the freezer wasn't freezing anything
4 of 7 people found this instruction helpful.
  • Tonya from Grand Prairie, TX
  • Really Easy
  • 15 - 30 mins
  • Socket set
Order the part from the Internet on Sunday, it mailed out on Monday and I received it on Tuesday. I unplugged the fan then undone 3 screws that held the fan bracket to the refrigerator pulled it out unscrewed 3 more nuts and replaced the fan on the bracket and I cut the old wire plug off the old fan and with 2 wire nuts put it on my new f an. Replaced the fan and bracket back on the refrigerator plugged it in and it works like a new refrigerator.
Was this helpful?
Thank you for voting!
Bad fan motor
3 of 5 people found this instruction helpful.
  • Mark from Farmington Hills, MI
  • Easy
  • 15 - 30 mins
  • Nutdriver
Pop off six mounting screws and the ground screw. Remove the fan blade and reattach. Reinstall. Save yourself big bucks.
Was this helpful?
Thank you for voting!
Ice buildup in freezer causing leaking water into fridge section
2 of 2 people found this instruction helpful.
  • Diane from Brighton, MI
  • Very Easy
  • 30 - 60 mins
  • Nutdriver, Pliers
In my case the defrost thermostat was not the problem. Not worth going through the hassle of checking the thermostat as I would have had to cut it out and test it in another freezer (while the food that was in the freezer was being stored elsewhere). I just ended up buying it and replacing it. So, like I said the defrost thermostat was NO T the issue. I ended up getting a drain tube heater strap, and have been keeping my eye on the fridge. It hasn't been long enough to say the strap fixed the problem, but all indications are pointing to that being the case.
Was this helpful?
Thank you for voting!
Mounting bracket was riveted on old motor, mounting bracket holes on new motor were different
2 of 2 people found this instruction helpful.
  • MIKE from ARLINGTON, OR
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Screw drivers
removed shims on screws holding motor together, enlarged hole in mounting bracket so motor screws could also go through mounting brackets.
Was this helpful?
Thank you for voting!
Fridge stopped cooling
3 of 5 people found this instruction helpful.
  • ray from palm bay, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I replaced the defrost relay folling instructions I read on the internet--and it still didn't work--So I replaced the compressor start relay which was easier than the defrost relay--it worked and the fridg is working good.
Was this helpful?
Thank you for voting!
Refrigerator coils froze up and 5 weeks later it got stuck in defrost.
2 of 2 people found this instruction helpful.
  • LES from GRAY, TN
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
The parts were reasonably priced, shipped promptly and received in a couple of days. I reviewed a YouTube video before starting that was beneficial. Huge savings over retail repair service. A+ replacement parts house and I would highly recommend.
Was this helpful?
Thank you for voting!
Broken plastic part at top of water fill tube to freezer
2 of 2 people found this instruction helpful.
  • Jay from Mt. Pleasant, WI
  • Really Easy
  • 30 - 60 mins
  • Screw drivers, Socket set
Simple. 1st, removed broken part to understand part (water fill tube to freezer, plastic part at top of fill tube cracked). 2nd go on your web site and look at prints to find part number, Study video to understand video. 3rd. Called customer service and lady was very nice and efficient. Placed order and received. Study video again a nd installed. My 9 year old grandson was visiting from out of town and assisted in installation. Just over 30 minutes to install
Was this helpful?
Thank you for voting!
Fan was noisy - bearing had failed
2 of 2 people found this instruction helpful.
  • Karl from Wellesley, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver
It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.
Was this helpful?
Thank you for voting!
Faulty light socket
3 of 5 people found this instruction helpful.
  • Larry from HOUSTON, TX
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Followed the video instructions.
Was this helpful?
Thank you for voting!
Drain clogging causing water to leak bottom of fridge
2 of 2 people found this instruction helpful.
  • Ted C from DSRT HOT SPGS, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
After watching videos how to replace went very easy.removed ice maker cut wires replaced switch put back together now working ok so far.
Was this helpful?
Thank you for voting!
Cimpressor would not start
5 of 11 people found this instruction helpful.
  • Oliver from Madison, AL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Checked compressor with amp meter, and found it was not running, found Overload Switch bad.
When removing old switch watch carefully which lug you move wires from, so you will know which
lug to put the new switch on.

BE SURE YOU KNOW SOMETHING ABOUT
ELECTRICITY!!
Was this helpful?
Thank you for voting!
The panel on the freezer door broke
2 of 2 people found this instruction helpful.
  • Carmela from Lincroft,, NJ
  • Really Easy
  • Less than 15 mins
I followed the directions that came with the new part. Thank you for making it so easy. You sent me everything I needed to make the repair.
Was this helpful?
Thank you for voting!
New Rental, Door Bar Broken
2 of 3 people found this instruction helpful.
  • Susan from Stratford, CT
  • Really Easy
  • Less than 15 mins
  • Pliers
Just moved into a new rental home and a few days in the bar that holds all the stuff -- milk containers, juice jugs, etc. -- in the refridge door falls off. The old tenants had "fixed" it with tape on one side and paint stirrers and caulk on the other side. (No kidding -- a real overkill job they did).

I looked up the model num ber online and found this site and promptly ordered the parts for $6 plus shipping. The parts came and snapped right in perfectly. Took only a minute.

I really only had to use pliers to pull out the oodles of hard swirly caulk from the slots in the door left from the overkill job by the previous tenants.

PartsSelect is awesome! The site makes it easy to look for the part you want and the parts were perfect -- No more stuff falling out the fridge door.

PS. This form made me select the age of the appliance. I really have no idea since I just moved in and it was already here.
Was this helpful?
Thank you for voting!
Removed crisper shelf to clean and it shattered into a million pieces
2 of 3 people found this instruction helpful.
  • Douglas from Naperville, IL
  • Really Easy
  • Less than 15 mins
Ordered the wrong shelf, returned it and ordered the correct shelf. Placed it on the frame. Service was two days.
Was this helpful?
Thank you for voting!
Shelves in freezer falling off
2 of 3 people found this instruction helpful.
  • wendy from palm coast, FL
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Went online with the model number, the part was very easy to find, diagrams helped me to have confidence in the choice. Parts came in two days, tore them open and used a screw driver to replace the broken shelf brackets, replaced shelves, I am a happy camper!!
Was this helpful?
Thank you for voting!
All Instructions for the 1069600515
91 - 105 of 304