- Home
- 1069532581
- Instructions
1069532581 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrig Door Cams wore out and made noises when opening and closing.
6 of 7 people
found this instruction helpful.
-
Michael from Lewisville, TX
- Easy
- Less than 15 mins
-
Pliers, Socket set
Followed Door Removal instructions by removing the Top Screws from the Cabinet. Lifted Door OFF the Metal Hinge. Unscrewed both Lower and Upper Cams from the Hinge and Door. Replaced with new after coating with Vasoline. Lifted Door back in place with help from Wife. Only problem was guiding the Door back onto the Hinge. Works fine. Two y
... Read more
ear old Frig. This is a design problem, as the cams should last longer than 22 months.
Read less
Was this helpful?
Thank you for voting!
Ice from automatic Ice maker was spilling out
7 of 10 people
found this instruction helpful.
-
Mary from Aliso Viejo, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
I pulled out the Ice maker tray. Unscrewed the front cover where the baffle had broke off. It was very easy after I found the correct part. Your site made it easy to fix my repair. Most people would have had to purchse a new refrigerator. Thanks to you I didn't have to go that way. The part came to me in about 3 days. I am very happy.
Was this helpful?
Thank you for voting!
light bulb in water ice freezer door went bad
8 of 14 people
found this instruction helpful.
-
Carl from RIVERSIDE, CA
- Very Difficult
- More than 2 hours
-
Screw drivers
I didn't. Don't know how to get to light bulb to change it for this specific model
Was this helpful?
Thank you for voting!
fridge and freezer stopped maintaining proper temp
5 of 5 people
found this instruction helpful.
-
Donald from CONWAY SPGS, KS
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I followed the repair videos that were provided by partselect and installed a bi-metal defrost thermostat in the freezer and a thermostat assembly in the fridge. The installation was not hard and everything is now working as it should. Thanks
Other Parts Used:
Was this helpful?
Thank you for voting!
water leaked when the paddel was pushed
6 of 8 people
found this instruction helpful.
-
Monica from EDMOND, OK
- Really Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Followed the video on parts page. I was worried I would brake the cover but learned from the video the right way to remove the front plate. I found the video very informing. Thank you for saving me a service call and the part cost was minimal compared to a new refrigerator .
Was this helpful?
Thank you for voting!
The frig/freezer shut off too often and would not stay cold.
7 of 11 people
found this instruction helpful.
-
Ron from Eaton Rapids, MI
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
The new thermostat assembly installed quite easily, just a couple of screws, but the thermostat probe however was kind of a pain in the rear. The probe is about 3 feet long and you have to remove a plastic sleeve from the old part and re-install on the new probe, it fits very tight and takes some time to do. Overall it was a very easy f
... Read more
ix.
Read less
Was this helpful?
Thank you for voting!
Refrigerator had shut down
7 of 11 people
found this instruction helpful.
-
Ronald from Martinsville, IL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Went on line ,ordered part on Friday afternoon ,Fedex was at my house Saturday Morning,,THIS SERVICE IS GREAT ,,THANK YOU VERY MUCH FOR BEING SO FAST
Was this helpful?
Thank you for voting!
Refrigerator water nozzle broke
5 of 5 people
found this instruction helpful.
-
Sandra from RESTON, VA
- Really Easy
- Less than 15 mins
-
Screw drivers
The nozzle of the water dispenser broke. I ordered the part which arrived the next day. I did not use the white line, only the black. I turned the water off, then I removed the screw under the broken nozzle and cut off it off from the line. I took a new screw and cut off the top with pliers, then twisted half of a screw in the old li
... Read more
ne and inserted the other half in the new line and pulled the line from the bottom corner of the refrigerator and connected it to the white line under the grid. Screwed the new nozzle back to the lever, replaced the grid and turned water on.
Read less
Was this helpful?
Thank you for voting!
Refregirator would not turn cooling back on after shutting down.
5 of 6 people
found this instruction helpful.
-
Olesya from ORLANDO, FL
- Very Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
After spending $250 on repair by calling appliance repair professional who changed relay in the fridge, the problem was not solved. I had to manually turn the switch off and on again to make sure my fridge would maintain its temperature. I read some similar problems on this web site, watched instalation video and decided to give it a try.
... Read more
Part came in very quick and it took me (female) 45 minutes to install the new part and refregirator worked like a champ. I would never call professional again until I try fixing the problem myself.
Read less
Was this helpful?
Thank you for voting!
Filler tube to the ice maker would freeze up
5 of 6 people
found this instruction helpful.
-
Fred from Rockport, TX
- A Bit Difficult
- 1- 2 hours
-
Screw drivers, Socket set, Wrench (Adjustable)
Pulled the fridge (KitchenAid side by side) out from the wall for the 1st time in a few years and dealt with those issues. Followed the instructions which were pretty clear. I was lucky enough that I did not need to retro fit any of the connections - it was really a straight forward replacement. The ice maker and the water dispenser have
... Read more
never worked better. Took about an hour.
Read less
Was this helpful?
Thank you for voting!
Freezer was dripping water into refrigerator below
5 of 6 people
found this instruction helpful.
-
John from Redmond, WA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed the old timer from the housing. The replacement came with good instructions. I followed the instructions corresponding to the color wires in my unit. The first time it was installed, the fridge did not come on and the temperature rose after a couple hours. Looked at the part and realized the defrost cycle must have kicked in. Need
... Read more
ed to slightly turn the gray slotted part to initiate the timer so it would stop the defrost and start the fridge. That did it! It must have advanced the timer so it could accumulate run time. Whole repair saved us $3000 in a new fridge.
Read less
Was this helpful?
Thank you for voting!
The flat support part of the stud had broken off, and I had removed the part to try to find a replacement. So, the shelf that holds one of the drawershad no front support on one side.
5 of 6 people
found this instruction helpful.
-
Mary from Olympia, WA
- Really Easy
- Less than 15 mins
-
Pliers
I removed the drawer and the shelf. I looked at the support on the other side to figure out how to insert the new one. Due to the shape of the "hook" part of the support, and the hole it needed to go into, I figured out which way I needed to insert it to be able to twist it so it would stay in place. From another online hint, and from
... Read more
talking to a repairman at a local shop (who had ordered me the wrong part) I knew I needed to twist it after inserting it. I used a pair of pliers to twist it counterclockwise, about a 3/4 turn. I put the shelf in and re-installed the drawer.
Read less
Was this helpful?
Thank you for voting!
3 years ago, we broke the shelf
5 of 6 people
found this instruction helpful.
-
James from Sherman Oaks, CA
- Really Easy
- Less than 15 mins
When we moved into the house, we cleaned the fridge and broke the glass shelf and thats how it has stayed.Then I finally got over my fear of ordering things "online" and within a week, we had a new shelf which just slid into place.
The shelf was packaged so well that even the UPS guy throwing over our locked gate didn't break it.
... Read more />Thanks Part Select....job done !!!
The shelf was packaged so well that even the UPS guy throwing over our locked gate didn't break it.
... Read more />Thanks Part Select....job done !!!
Read less
Was this helpful?
Thank you for voting!
broken kickplate
8 of 15 people
found this instruction helpful.
-
Patricia from Ypsilanti, MI
- Easy
- Less than 15 mins
just snapped it on,
Was this helpful?
Thank you for voting!
Lower Light Socket removed and Wires capped with wire nuts
6 of 9 people
found this instruction helpful.
-
Wayne from Arlington, TX
- A Bit Difficult
- Less than 15 mins
My tenants moved out of my rental property and abandoned their refrigerator there. The freezer door would not close properly because someone had previously removed the lower door support bracket and failed to replace the lower bracket shim that positions the lower part of the freezer door properly out from the refrigerator cabinet causin
... Read more
g the door gasket seal to bind before the freezer door was fully closed. I removed and replaced this lower door bracket with a new shim made up of serveral thicknesses of cardboard to achieve this spacing and freezer door now closes and seals properly. They had never connected a water supply to the refrigerator although this model is equiped with an ice maker and in door ice and cold water dispenser. The access panel on the back of the unit had been previously removed and discarded. I made up a new access panel from cardboard and connected the water line to the solenoid valve. Valve was so old it would barely open when valve energized and water flow was too slow to make proper sized ice cubes and fill a water glass. I purchased a new water solenoid valve and replaced ther original valve and cured that problem. Replacing the access panel cured an improper cooling problem because with panel removed, most of the air flow bypasses the condenser coils. Lastly I replaced the upper tubular light bulb and the lower light socket I purchased here and installed a 40 watt bulb in the new light socket. Presto! I was able to turn non working abandoned refrigerator into a workable unit.
Read less
Was this helpful?
Thank you for voting!