106950 Kenmore - Instructions

I had a technician called out to the house to look at repairing several appliances that all have broken parts after just 3 yrs of use. Hood, Microwave, Oven, Fridge all in need of minor repairs..

Anyway - the estimate was $240 to replace the ice maker. I ordered PS358591 for $104. and it came in a couple days.. I took out one ... Read more screw - slid out the icemaker, unplugged it - plugged in new one and slid it in the slot - and done !! Took about 20 mins.. didnt need any of the wiring harnesses in the box from partselect. Was way to easy to do !!

Thank you !

First, I unplugged the power to the entire fridge, and then removed the ice tray and ice door. Next, I unplugged the flat plug in the very back left behind the icemaker. Then I removed the 1/4" hex head sheet metal screws (2) and the phillips head screw (1) that hold the icemaker to the left side of the freezer wall. New icemaker came ... Read more with a different style trip arm, so I used it. Plugged new icemaker in before reattaching it with the same (3) screws. Replaced ice tray and door, plugged in fridge, and waited....Dumped its first batch of ice maybe a couple of hours later. Not much trouble-shooting is needed when the entire icemaker is as easy and relatively inexpensive to replace as this. Twenty minutes, max.

We weren't sure if the problem was in the Water Inlet Valve or in the Icemaker Control & Motor Assembly. The water in the door did work. We removed the Water Inlet Valve & tested it with an Ohm Meter. It tested good so we put it back in. We then ordered the Icemaker Control & Motor Assembly. When it arrived we installed it and waited ... Read more a few hours but the icemaker still did not fill with water. We telephoned a parts store and were told the problem could be the thermostat or we could replace the whole icemaker. We replaced the whole icemaker.

It was easy to snap off the old shelf and snap in the new. The price was right. The part was right. If I need to, I'll be back.

1. Unplug refrigerator to remove power!
2. The timer is inside the control housing located at the top of the refrigerator compartment.
3. Remove two control knobs (the pull off).
4. Remove the front panel escutcheon. The panel is not held in place with screws, but can be gently pried off.
5. Remove two screws from the ... Read more back that hold the housing in place.
6. Remove screws from the front that hold the housing in place.
7. Drop housing down (still attached by wires - do not detach). Timer is inside housing, located on right.
8. Follow the instructions provided to identify your particular wiring setup. You'll find the wiring diagram (on my model) at the bottom of the refrigerator, alongside the defrost catch pan, behind the airflow grille.
9. Remove connector from timer terminals (4).
10. Remove two screws/nuts that hold the timer in place.
11. Install replacement timer following included directions. Read and follow ALL instructions applicable to your particular model and wiring setup.
12. Reassemble by reversing the steps above.
13. Note: You may need to "jog" the replacement timer when you first plug the refrigerator back in, if the timer happens to be in a "defrost cycle" (the compressor won't start). This can be done by inserting a wide bladed screwdriver into the hole below the timer, aligning it with the timer shaft, and slightly turning the shaft CW. Don't force it, and don't turn it very far.

I have an old DIY home repair book and I saw that the ice maker repair wasn't hard, so I ordered the parts from Part Select. 1 day to arrive...super service. The site is very helpful with diagrams about the parts. The repair was a cinch...EXCEPT I forgot to unplug and got a little zap. The shelf pegs were a breeze because I had read other ... Read more 's stories about how to remove and replace on this site. Go try to do it...get a book at library if you need some direction.

rmv panel (5min) rmv fan/motor 3 screws (10 m) cut wire 2in from motor, re route remainder of wire to front so can strip for wire nuts. ( 10m) attach old fan to new motor, place in old opening ,3 screws, a little fussy to align, ( 15m ) route and strip wire from new motor , zip ties work well, wire nuts , plug in fridge vola, no noise, c ... Read more lose up, reverse panel. ( 20m). i also took time to clean grilles with small vac and damp rag, ( looks and sounds like new) bob Wi.

First I unplugged the frig, and turned offed the water and ice dispenser using the on/off panel switch. I removed the panel by inserting a small flat blade screwdriver at the bottom of the panel where the plastic studs locked the panel in place. By inserting a little upward pressure, the panel popped right ouff. The Micro Switch was very ... Read more easy to remove and replace. Just make sure that the plunger on the ice dispenser makes solid contact with the switch when depressed.

I took the old drawer out and replaced it with the new one!
I hooked a new door bin in the door for more room!

DISCONNECT POWER. Removed all shelves/baskets.Popped upper panel off (just clips in) Removed 6 screws in lower back panel ( 3 each side) slid panel in place but down. You can then easily see the defrost thermostat/defrost termination switch. Cut the wire connectors (pink n brown wire) stripped back wire, attached new defrost thermostat. ... Read more Thermostat clips on. New thermostat ohm's at 5.5, old one was "open". Slid cover back up meeting the upper cover grooves. Screwed lower panel in. Put shelves etc back in. Plugged in. Turns on, put a bottle of water in freezer. Checked a while later, frozen. has been frozen for a week.
-James

I have a side by side so in order to access the bi-metal switch I first had to empty out the freezer. The switch is clipped on to the top of the evaporator coil. I had to remove 8 screws to remove the back panel of the freezer compartment. The bi-metal switch was right there in plain view. There are two colored wires that come out of ... Read more the switch. I tried pulling them out of the socket they were plugged into but gave up for fear of breaking something. I ended up cutting the wires and splicing them together. I used the plastic twist caps. I made sure when I closed everything back up that the open end of the caps were pointing down so no water can accumulate in them. It has been 3 days now and so far so good

Didn't know if part was replaced from the front or back of door. Removed back/inside first. Good excuse to clean mold found in places not normally seen. The only real problem was getting the face off the dispenser without breaking it. I now know it snaps off from the bottom. To replace one little nozzle you have to replace about 10' ... Read more of tube. When I pulled the old tube out. I attached fishing line to it and used to fishing line to help feed the new tube through the door.

Removed the old one. Removed the handle attachment and placed it on the new drawer and slid it in place. Just that easy.

First of all, here's a warning to all -- I took the glass shelf / pan cover out to clean it -- with a sponge wet with COLD water and the shelf literally exploded on me. This is the second such incident. Both times I have been lucky and no one was hurt.

The shelf was easily identifiable by part number based on model number. E ... Read more asy to locate the model number on plate above top shelf inside refrigerator (right hand side in my case).

Only had to carefully set glass shelf in frame -- no issues. I was able to use a screwdriver to remove the shelf support stud and basically pop the replacement back in with no issue.

Thank you Parts Select for your simplified system to order replacement parts, and the speed with which it was received.

While moving our refrigerator when remodeling the kitchen, the front roller assembly shattered from age. The original set was made of nylon and age made it very fragile. Also to make the move easier, we removed the shelves. In the process the lower shelf support stud snapped.

When the parts came the first thing repaired was th ... Read more e shelve support stud. Very easy job to do, just take the pliers and rotate the broken stud counterclockwise a quarter turn and remove. Put new stud in the hole in the same position as the removed stud and gently, but firmly rotate the stud a quarter turn clockwise until it seats.

The front roller assembly requires a socket set, block of wood about 1/2 - 1" thick flashlight and 4’ level. First, remove the front grill by opening both doors of the side by side and pulling the grill out of its left and right side anchors. Close the doors. Place the block of wood under the front support near the center. Remove the leveling screw from the old assembly and install it loosely in the new assembly as the new assembly has no leveling screw. This will now allow you to remove the old assembly by removing the remaining screw in the roller assembly on the front refrigerator support and turning the roller assembly slightly counterclockwise and pulling out the front. You may have to wiggle it, as it sits in a slot on the side support of the refrigerator. To install, place the new assembly in the same position as the old, locate the slot with the flashlight and push the roller set tab into the slot. Attach the support screw and tighten while holding the assembly in place. It is a good idea to replace both rollers at the same time. The same rollers will fit both sides. Now level the refrigerator by tightening the leveling screw until the front rollers now touch the floor. Next, place the level on the top of the refrigerator diagonally but not on top of the door supports. Turn the leveling screws until the bubble is in the center when the level is set in either diagonal position. Replace grill and you done.