- Home
- 1069432410
- Instructions
1069432410 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bottom drawer cover cracked because it was not strong enough to support weight in the drawers and weight on the shelve due to poor design.
4 of 6 people
found this instruction helpful.
-
Douglas O from Wichita Falls, TX
- Really Easy
- Less than 15 mins
I just went on line and identified the drawer cover and ordered a new one that was too expensive in my opinion.
I pulled out the old one and installed the new shelf and then inserted the two drawers.
I pulled out the old one and installed the new shelf and then inserted the two drawers.
Was this helpful?
Thank you for voting!
Part went bad the freezer was freezing up and refrigerator not getting cold
3 of 3 people
found this instruction helpful.
-
Jessica from WILLIAMSBURG, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver
I pulled off the panel covering the part in the freezer cut and stripped the wires. Used crimper and connectors put the new part on put the wires band panel back on and plugged the refrigerator back in. Everything works just fine now.
Was this helpful?
Thank you for voting!
selection of part
3 of 3 people
found this instruction helpful.
-
Bernard from MILLBURN, NJ
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
Following the diagram of parts so that I could order the right items was the most difficult part of the job. The web site for this task needs to be more friendly.
Other Parts Used:
Was this helpful?
Thank you for voting!
badly worn cam
3 of 3 people
found this instruction helpful.
-
harry from KINGSPORT, TN
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Exactly as the demo instructed. It was very detail friendly and was very easy to follow.
Was this helpful?
Thank you for voting!
My glass shelf shattered while i was cleaning the refrigerator and I was very skeptical at being able to find a replacement since the refrigerator is a 1991 model.
4 of 6 people
found this instruction helpful.
-
Charlotte from Leeds, AL
- Really Easy
- Less than 15 mins
I ordered the shelf on-line halfway believing it would not fit - it arrived THE NEXT DAY and was the exact fit for the model. I was elated and the whole incident renewed my faith in customer service. PartsSelect was great and I will re-order for future needed repairs.
Was this helpful?
Thank you for voting!
Raplaced switch
5 of 9 people
found this instruction helpful.
-
Winston A from Brooklyn, NY
- Really Easy
- Less than 15 mins
-
Pliers
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Was this helpful?
Thank you for voting!
Freezer was icing up and leaking. Refrigerator side would not keep cold.
3 of 3 people
found this instruction helpful.
-
Camille from Glen Ellyn, IL
- Easy
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers
We emptied out both sides, refrigerator and freezer, and followed the instructions in your video. We turned it off and disconnected the power. We took off the freezer door first. It made it much easier to get the shelves out and reach way back into the freezer. We removed the light and cover, then the ice auger motor. The back panel wa
... Read more
s easy to lift and remove. The wire assembly was a little hard to understand at first, but when we figured it out it was easy to remove and replace the bimetal defrost thermostat. We did check the video when we had the wire harness out, to make sure we got it right. We reassembled the freezer's inside parts and reattached the door. Before we turned the power back on, we scrubbed down the entire refrigerator. When we turned the power back on, the refrigerator and freezer were operating quietly - no sparks or explosions or shorting out - hooray! And the problems were solved.
The most important resource is your video. It looked like something we could do, and then ordered the parts. Our repair took a long time because we checked the video so many times. Thank you so much for the great information and the excellent parts. We could not have done it without you.
The most important resource is your video. It looked like something we could do, and then ordered the parts. Our repair took a long time because we checked the video so many times. Thank you so much for the great information and the excellent parts. We could not have done it without you.
Read less
Was this helpful?
Thank you for voting!
door closing cam was broken
3 of 3 people
found this instruction helpful.
-
lizie from nantucket, MA
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Screw drivers
the process was pretty straight forward though the part came without instructions. We were able to replace the part improperly with ease. however, we were not able to get the pieces aligned properly for a long time. We ended up taking the door off many times to try to realign the pieces. After many hours I finally unscrewed the bottom
... Read more
cam while the door was in place. The piece popped into place and all was fixed. Had the part come with directions telling us to do this we would have replaced the cam within 15 minutes!
Read less
Was this helpful?
Thank you for voting!
frame for top of drawer had plastic side rails cracked
4 of 7 people
found this instruction helpful.
-
Andrew from Rockville, MD
- Really Easy
- Less than 15 mins
just replaced the frame - easy to remove old broken frame and replace with new one
Was this helpful?
Thank you for voting!
defective light switch
3 of 4 people
found this instruction helpful.
-
THOMAS from WILLARD, OH
- Really Easy
- Less than 15 mins
inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
Was this helpful?
Thank you for voting!
Refrigerator door on a side by side unit would not stay closed.
3 of 4 people
found this instruction helpful.
-
John from Conyers, GA
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
First empty the shelves on the refrig. door. Then removed the upper hing cover and removed the three screws holding the hinge to the body of the refrigerator. Lifted the door off the bottom hinge and placed it clear of the unit.
Inspected the bottom hinge and cleaned off the screw holding the closing cam, then with a nutdriver remove ... Read more d the screw holding the cam and removed the cam from the hinge. Installed a new cam closer, secured the cam with a screw. Hanged the door back on the lower hinge and re-installed the upper hinge. Job Complete!
Inspected the bottom hinge and cleaned off the screw holding the closing cam, then with a nutdriver remove ... Read more d the screw holding the cam and removed the cam from the hinge. Installed a new cam closer, secured the cam with a screw. Hanged the door back on the lower hinge and re-installed the upper hinge. Job Complete!
Read less
Was this helpful?
Thank you for voting!
side by side freezer door wouldn't close
3 of 4 people
found this instruction helpful.
-
Dorothy M from Galway, NY
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
Friend did for me, had to take off door after disconnecting water like a power cord from top of door, now works fine, also did the cam on frig side too, works better also.
Other Parts Used:
Was this helpful?
Thank you for voting!
changed the light bulb still would not work so I figured it was the switch sure enough.
3 of 4 people
found this instruction helpful.
-
anthony from HAVELOCK, NC
- Really Easy
- 15 - 30 mins
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this helpful?
Thank you for voting!
freezer section freezing up ( not defrosting )
3 of 4 people
found this instruction helpful.
-
John from COLUMBIA, LA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
ordered the parts ,defrost timer and bi-metal thermostat,assumed it would be more practical to replace both than take a chance . watched a video on how to disassemble the control panel and remove the the timer and the back panel of freezer for the bi-metal thermostat,very clear instructions provided .took about 25 minutes to replace both
... Read more
parts and now is working properly again,,Thanks Again PartSelect for the fast service and delivery
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...
3 of 4 people
found this instruction helpful.
-
David from Hemet, CA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull t
... Read more
he connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!
Read less
Was this helpful?
Thank you for voting!