1069430282 Kenmore Refrigerator - Instructions

All Instructions for the 1069430282
121 - 135 of 434

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
frame for top of drawer had plastic side rails cracked
4 of 7 people found this instruction helpful.
  • Andrew from Rockville, MD
  • Really Easy
  • Less than 15 mins
just replaced the frame - easy to remove old broken frame and replace with new one
Was this helpful?
Thank you for voting!
Refrigerator would not stay cold and freezer would thaw.
3 of 4 people found this instruction helpful.
  • Michael from SYLVA, NC
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I watched the repair video and did exactly as described. Excellent video and step by step instructions. Follow them and you cannot go wrong.
Was this helpful?
Thank you for voting!
shelf stud had broken
3 of 4 people found this instruction helpful.
  • cal from lakeside, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Pliers, Screw drivers
pryed out old stub of stud with the tip of a flat head screw driver. It really did not want to come out because of the metal wings on the side of the stud. When I finally got it out the hole was a little rough but the new stud fit in the old hole and was not to wobbley. The shelf is heavy enough to make it stable. The new stud is also lon g enough to support the shelf even though the hole was not really in new condition after the old stud was pried out.
Was this helpful?
Thank you for voting!
Freezer Temp was -20 to -30 degrees F. and did not defrost because of the extreme low temperatures.
3 of 4 people found this instruction helpful.
  • George from ENDWELL, NY
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
The Video on U tube was helpful. I have a side by side model and it was difficult to work in such tight quarters to attach the new part . I found that by removing the cable assembly it was much easier to attach (cut and crimp) the new part on the outside , then reinsert the assembly. The new part resolved my problem. Don't panic when you try and remove the cable assembly. Hope this is helpful.
Was this helpful?
Thank you for voting!
Machine Leaking Water
2 of 2 people found this instruction helpful.
  • Frank from BERKELEY HTS, NJ
  • Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
I did some tests and determined that the tub-to-pump drain hose had a leak in it.I then looked on the web to find disassembly instructions. I have a stacked washer dryer combination in a very confined space. The repair involved disconnecting both the washer and dryer from the water, gas, electric and venting systems first, then unstacking the dryer from the washer (not so easy, it required a helper). The machine was then pulled out so I could get at the parts necessary to remove the outside components and sheet metal. Then, I disassembled the top, front and access panel in the back. The disassembly went very well. I got access to the drain hose assembly and removed it fairly easily. I ordered a replacement drain hose assembly and found that installing the large port of the assembly was very difficult. (The two other ports were easy.) After thinking about it, I tilted the machine back a bit so I could try it from the bottom. That worked fine.I then reassembled and tested the machine. No leaks. Good luck with yours!
Was this helpful?
Thank you for voting!
Refrigerator door clunking on opening and closing
2 of 2 people found this instruction helpful.
  • Bruce from Stuart, FL
  • Easy
  • 1- 2 hours
Following the instructions on the site I removed the upper hinge cover and hinge(after removing the shelves from the door). I replaced both cams on the bottom hinge, reinstalled the door and the problem was solved. A couple of hints that may speed up the process: 1. On installing the door cam, I didn't get the holes in the door and cam al igned well due to a bit of interference from the metal tab on the door, so I temporarily inserted the upper hinge pivot in the bottom hole and retightened the cam. 2. I decide to re-align the freezer door . After this, the ice and water dispensers didn't work. Turns out the internal freezer light switch which also acts as a cutoff switch for the door dispensers wasn't being activated. Easy to adjust once the cause was discovered.
Was this helpful?
Thank you for voting!
Fridge stopped cooling
3 of 5 people found this instruction helpful.
  • ray from palm bay, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I replaced the defrost relay folling instructions I read on the internet--and it still didn't work--So I replaced the compressor start relay which was easier than the defrost relay--it worked and the fridg is working good.
Was this helpful?
Thank you for voting!
Refrigerator coils froze up and 5 weeks later it got stuck in defrost.
2 of 2 people found this instruction helpful.
  • LES from GRAY, TN
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
The parts were reasonably priced, shipped promptly and received in a couple of days. I reviewed a YouTube video before starting that was beneficial. Huge savings over retail repair service. A+ replacement parts house and I would highly recommend.
Was this helpful?
Thank you for voting!
Thermostat didn't work as suppose to be
2 of 2 people found this instruction helpful.
  • Francisco from KENNETH CITY, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I follow the video From The Tech Guy ( Gentleman ). Thank you... Best Regards .Fco
Was this helpful?
Thank you for voting!
Refrigerator running to much and freezer to cold
2 of 2 people found this instruction helpful.
  • DONALD from ST AUGUSTINE, FL
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
watched your instructions
Was this helpful?
Thank you for voting!
Refrigerator would run, then stop on it's own would start again if I would change the temp setting on refrigerator
2 of 2 people found this instruction helpful.
  • Duane from CASA GRANDE, AZ
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
just as the installation video show (very helpful) however the sheath tube that was pulled off of the old capillary tube did not go back on the new tube near as easy as the video showed. Got it on however and refrigerator is working like a champ now
Was this helpful?
Thank you for voting!
Fan was noisy - bearing had failed
2 of 2 people found this instruction helpful.
  • Karl from Wellesley, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver
It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.
Was this helpful?
Thank you for voting!
Drawer cover was broken and shelf support was missing
3 of 5 people found this instruction helpful.
  • Bonnie from Concord, CA
  • Really Easy
  • Less than 15 mins
I removed the crisper drawer cover and took out the glass and put it in the new drawer cover. The freezer support shelf had been missing for a while. All it needed was the shelf suuport that slid down over the stud in the freezer wall. Couldn't be simpler! No tools needed.
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people found this instruction helpful.
  • Yafa (and David) from Bothell, WA
  • Easy
  • Less than 15 mins
  • Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
The drawer sliders on the covers had broken and the drawers didn't stay in.
3 of 5 people found this instruction helpful.
  • Sara from Baraboo, WI
  • Really Easy
  • Less than 15 mins
My main rave for this site is I received my parts in less than 24 hours!!
I was shocked at how fast they arrived ( I didn't pay for overnight shipping either)
The repair was simple. Pulled out the old broken covers, put in the new ones and slid the drawers back in. Sure is nice to have them seal again! :)
Was this helpful?
Thank you for voting!
All Instructions for the 1069430282
121 - 135 of 434