- Home
- 1069410482
- Instructions
1069410482 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice maker did not work
4 of 5 people
found this instruction helpful.
-
Judy from Galveston, IN
- Easy
- Less than 15 mins
-
Nutdriver
Took the old one out and plug the new one in, simply as 1 2 3. Order the part one morning,it was here the next afternoon, the ice maker was fixed in less than a half hour. we will order from you the next time.
Was this helpful?
Thank you for voting!
Lights not working some times
4 of 5 people
found this instruction helpful.
-
Harry from COLUMBIA STA, OH
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers
Removed old switch and installed new - but did not solve problem
Was this helpful?
Thank you for voting!
Broken filler tube at threaded connection
4 of 5 people
found this instruction helpful.
-
Matthew from Phoenix, AZ
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
After discovering that the water noise was coming from the rear of the refridgerator upon pulling it foward I discivered the connection line had broken. So i got a phillips screw driver and removed the the two mounting screws and saw it was one piece. I easliy found the part on PartSelect website and once I got I merely swaped them out
... Read more
and it works good as new!
Read less
Was this helpful?
Thank you for voting!
shelf support stud broke in half
4 of 5 people
found this instruction helpful.
-
Cindy from Fort Worth, TX
- A Bit Difficult
- 15 - 30 mins
-
Pliers
Removing old stud was difficult. It will not stap or pull out. Had to cut it off with a Dremel tool, then drill into the center of the old stud and pull out the pieces with needle nose pliers. Be careful, there are 2 metal pins on the side of the hole in the wall of the frid that need to stay there. These are in addition to the 2 met
... Read more
al pins on the shelf support stud. New stud popped right in easily.
Read less
Was this helpful?
Thank you for voting!
Frig wasn't reliable,kept going off and staying off until I discovered "hitting the knob" trick.
4 of 5 people
found this instruction helpful.
-
Bob from Norman, OK
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
I followed the procedures that others described that had the same problem,very handy
Was this helpful?
Thank you for voting!
Ice Maker didn't produce ice cubes.
4 of 5 people
found this instruction helpful.
-
Michael from Long Valley, NJ
- Easy
- 30 - 60 mins
-
Nutdriver
It was not complicated but it took more squeezing and reaching into the narrow space than actually removing three screws and unplugging the electrical harness. But that was all that was necessary, to install, three screws held the unit in place and re-connect the electrical harness. It saved me about $100 in labor and the inconvenience of
... Read more
scheduling a service call and waiting for a week or so. The best part was that I ordered the unit on line on Tuesday eveining and it was at my home by Friday afternoon with no extra shipping charges. Great service!.
Read less
Was this helpful?
Thank you for voting!
Ice maker not working
6 of 11 people
found this instruction helpful.
-
Raoul from Thousand Oaks, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
take out Ice maker tray, remove three screws holding the ice maker, unplug electrical connector. Replace with new Ice maker,Ice started to fill the tray. ENJOY!!
THANKS.
THANKS.
Was this helpful?
Thank you for voting!
Replaced broken shelf supports
4 of 6 people
found this instruction helpful.
-
Cheryl from Los Angeles, CA
- Really Easy
- Less than 15 mins
Took out old pieces and popped new ones in, just like that!
Was this helpful?
Thank you for voting!
Would not make ice any longer
4 of 6 people
found this instruction helpful.
-
James from Concord, MA
- Really Easy
- Less than 15 mins
-
Nutdriver
I determined that the ice cube maker was no longer heating the cubes so they could be released into the ice tray. After ordering a new unit, taking out four screws and disconnecting the quick disconnect of wires I plugged the new one in and we were back in business.
Was this helpful?
Thank you for voting!
Bottom drawer cover cracked because it was not strong enough to support weight in the drawers and weight on the shelve due to poor design.
4 of 6 people
found this instruction helpful.
-
Douglas O from Wichita Falls, TX
- Really Easy
- Less than 15 mins
I just went on line and identified the drawer cover and ordered a new one that was too expensive in my opinion.
I pulled out the old one and installed the new shelf and then inserted the two drawers.
I pulled out the old one and installed the new shelf and then inserted the two drawers.
Was this helpful?
Thank you for voting!
icemaker was overfolwing with water
5 of 9 people
found this instruction helpful.
-
David from West Bloomfield, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
ordered the part, pulled out the icemaker unit, removed the module, put the new module in, reinstalled the ice maker unit and let it run.
Was this helpful?
Thank you for voting!
Fill cup broke.
6 of 12 people
found this instruction helpful.
-
Aliki from Miami, FL
- Really Easy
- Less than 15 mins
Very easy to order from parts select. Took seconds to replace.
Was this helpful?
Thank you for voting!
Installing old ice maker in new freezer
3 of 3 people
found this instruction helpful.
-
Harry from Ten Mile, TN
- Really Easy
- 15 - 30 mins
-
Screw drivers
I was able to transfer my old ice maker from my old Roper Refrigerator/Freezer into my new Whirlpool Sidekick Freezer. Everything transferred directly except for the water fill tube. I ordered one on line and simply cut it to the right length, removed the cover plate inside the freezer compartment and the little sticker from the outside.
... Read more
Inserted tube and fastened in place with two screws (not provided but was able to use the screws that were in the holes inside the freezer before the ice maker went in. Works great. By not buying the ice maker with the freezer I saved a hundred bucks or so.
Read less
Was this helpful?
Thank you for voting!
The icemaker quit making ice.
3 of 3 people
found this instruction helpful.
-
Tom from Summerville, SC
- Really Easy
- 15 - 30 mins
-
Screw drivers
With instructions from PartSelect.com this was an easy fix. I tested the motor's electric as suggested and was satisfied that the Motor Module (WPL W10190935) would correct the problem. UNPLUG THE REFRIGERATOR! I popped the outside plastic cover off to expose the unit. (1) remove the wire unit that runs the length of the cube maker (2) re
... Read more
move the 3 screws that secure the motor unit and carefully remove it (3) carefully line up the new unit, slide in place and replace the 3 screws (4) install the wire that was removed in step(1). Connect electric to the refrigerator and wait about 2 hours for your first ice cubes. PartSelect.com is the ONLY supplier that you will ever need! Great instructions and trouble shooting suggestions. Shipping is incredibly fasssst! Customer contact is awesome. Don't hesitate to buy from them! Saved me about $200.! Good luck....Tom in SC
Read less
Was this helpful?
Thank you for voting!
coating (clear) on ice cube mold peeling off
4 of 6 people
found this instruction helpful.
-
Matthew from Collegeville, PA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed ice maker from fridge. Removed motor assembly (3) screws on cover, and (2) screws inside. Removed mold (3 screws on bottom) and replaced everything in reverse order. Note: Turned ice maker off for several days while waiting for parts. The water line on this particular model will freeze inside the freezer if ice isn't made for
... Read more
several hours/days. You will have to defrost to begin making ice again.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!