- Home
- 1069344280
- Instructions
1069344280 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Faulty light socket
3 of 5 people
found this instruction helpful.
-
Larry from HOUSTON, TX
- Very Easy
- 15 - 30 mins
-
Screw drivers
Followed the video instructions.
Was this helpful?
Thank you for voting!
No ice
2 of 2 people
found this instruction helpful.
-
GARY from WEST CHESTER, PA
- Really Easy
- 15 - 30 mins
-
Screw drivers
I removed the icemaker. One screw at the bottom and then unplug the electric. Remove the old motor from the face that has 3 screws holding it. Put the new motor in. A very simple job. I now have a full ice bin by the next morning.
Was this helpful?
Thank you for voting!
The coating on the mold /heater unit as cracked and some broken off and cause the water to drip down in the Ice trace and form large icicles
3 of 5 people
found this instruction helpful.
-
James from Tomball, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I just removed the unit and replaced the mold/'heater with the new one and re-installed. It was very easy and didn't have to turn off the refer. or empty the frozen food.
However , there were not instruction that came with the mold/heater unit. I had no problem but other do-in-uselfers may need some basic instructons
Jim
However , there were not instruction that came with the mold/heater unit. I had no problem but other do-in-uselfers may need some basic instructons
Jim
Was this helpful?
Thank you for voting!
the freezeer gasket was not sealing properly and the refrigerator door one was torn
2 of 3 people
found this instruction helpful.
-
christine from hackensack, NJ
- A Bit Difficult
- 1- 2 hours
-
Socket set
Since the parts arrived with no instructions and I had a vague idea of what I had to do, I went on You-tube and watched a video which was very helpful. It was a little difficult at first but once I got the hang of it things went smoothIy. It's like a brand new refrigerator now!
Other Parts Used:
Was this helpful?
Thank you for voting!
Water liking into the ice tray causing an iceberg
2 of 3 people
found this instruction helpful.
-
Joe from Newbury Park, CA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
Removing the ice making assembly from the Ice compartment was not difficult except that two of the 3 screws we not visible without a mirror and then my nut driver was 5" long making it very tight quarters, so it was a time consuming process to remove them.
Once the 3 screws were removed the wiring harness was easily disconnected and ... Read more the whole assembly came out.
The next step was to figure out how to remove the faulty part from the rest of the assembly.
After some strong persuasion the part would not separate from the control Assy. (The front of the unit) To complete the job I had to pull the front cover and unplug the motor and heater assy to expose two additional screws that had to be removed to pull the defective part out. The reassembly went quite easy except the 2 screws that you need a mirror to see. I was also trying to hurry because the frozen items were not holding all that well after the door was open for about an hour and a half. An instruction sheet showing the steps would have cut the time over 1/2!
Once the 3 screws were removed the wiring harness was easily disconnected and ... Read more the whole assembly came out.
The next step was to figure out how to remove the faulty part from the rest of the assembly.
After some strong persuasion the part would not separate from the control Assy. (The front of the unit) To complete the job I had to pull the front cover and unplug the motor and heater assy to expose two additional screws that had to be removed to pull the defective part out. The reassembly went quite easy except the 2 screws that you need a mirror to see. I was also trying to hurry because the frozen items were not holding all that well after the door was open for about an hour and a half. An instruction sheet showing the steps would have cut the time over 1/2!
Read less
Was this helpful?
Thank you for voting!
No Ice, water was valve working, the ice tray was turning
2 of 3 people
found this instruction helpful.
-
Jerry from MERRITT IS, FL
- Really Easy
- 30 - 60 mins
-
Screw drivers
Installed the icemaker control assembly this corrected the problem suspect contacts on the old unit were not making a good contact over time, due to the damp area in the freezer the new unit corrected the repair easy repair.
Was this helpful?
Thank you for voting!
Icemaker not producing adequately
3 of 6 people
found this instruction helpful.
-
David from Shalimar, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Thought The issue was the solenoid valve. Took a lot of research but finally found through parts select. Perfect match and easy to install, but unfortuantely, it did not solve the problem of poor ice production. Now would appear that the icemaker itself needs to be replaced.
Was this helpful?
Thank you for voting!
Icemaker shaft would not turn
2 of 3 people
found this instruction helpful.
-
Richard from Lewistown, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Installed new motor control
Was this helpful?
Thank you for voting!
Ice maker not working....
7 of 18 people
found this instruction helpful.
-
Marie from Homosassa, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Took the front of the ice maker off. Noticed the arm inside was broken, found the part on your site and ordered it.....super fast delivery. Replace the moter assembly and off she went. had ice in about 30 minutes. Thanks for your services and I will highly recommend you to others......Thanks again.
Was this helpful?
Thank you for voting!
not making ice
2 of 3 people
found this instruction helpful.
-
salvatore from wantagh, NY
- Really Easy
- Less than 15 mins
-
Wrench set
first i removed 1 screw, then pulled out the ice maker, unpluged the electrical wire, i removed the white plastic cover , then an additional 3 screws . i pulled off the ice maker control . replaced with new ice maker control. i repeated the steps to put back the ice maker ...so
super quick part delivery !!!
super quick part delivery !!!
Was this helpful?
Thank you for voting!
The plastic water fill tube got cracked when we moved. I called a parts company and they told me they couldn't just sell me the tube I would have to buy a whole kit for about $50 dollars. I decided to glue the tube. It worked for a while then it started leaking. So I thought I would have to buy
3 of 6 people
found this instruction helpful.
-
Joseph from Chesterfield, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
I hand screwed the fill tube into the water tube and stuck it into the freezer hole. I screwed the fill tube to the back of the refrigerator.
Thanks so much! You saved me a bundle!!
Thanks so much! You saved me a bundle!!
Was this helpful?
Thank you for voting!
Broke light switch while cleaning
2 of 3 people
found this instruction helpful.
-
Gail from Golden, CO
- Really Easy
- Less than 15 mins
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this helpful?
Thank you for voting!
Ice maker stopped working
2 of 3 people
found this instruction helpful.
-
Marinus from Crestone, CO
- Really Easy
- Less than 15 mins
-
Screw drivers
Removed the control and motor assembly by removing the plastic cover and three screws. Shut off the power to the refrigerator while removing the control and motor assembly (and also when installing the new one). Tested the motor using an AC power cord. The motor had apparently failed. Ordered the repair part and installed it taking ca
... Read more
re that the motor drive shaft and shut off arm were correctly aligned. The icemaker began to work properly when power was restored. The cost of this repair was about half the cost of replacing the entire icemaker.
Read less
Was this helpful?
Thank you for voting!
motor assembly was shorting out
2 of 3 people
found this instruction helpful.
-
Paul from Boring, OR
- Really Easy
- Less than 15 mins
-
Nutdriver
I removed the cover to assembly ,3 screws and it came right off. points were wore out. Thank you for a prompt delivery. It was delivered much faster then I expected.
Paul First time dealing with you ,thanks
Paul First time dealing with you ,thanks
Was this helpful?
Thank you for voting!
Crisper post was missing
3 of 6 people
found this instruction helpful.
-
Annette from Coon Rapids, MN
- Easy
- Less than 15 mins
My refrigerator is about 26 yrs old and the part I received must have been for newer models, but I was able to insert the part into a little rubber part attached to the bottom the refrigerator,
Was this helpful?
Thank you for voting!