- Home
- 1069334311
- Instructions
1069334311 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The original ice-maker had a defective module and the ice-maker kit cost less than a replacement module
-
Gary from Morganton, NC
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Replaced original ice-maker with the ice-maker from the kit. Operational check was good.
Was this helpful?
Thank you for voting!
leaky ice maker/black flakes in ice
-
Terri L from Coarsegold, CA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
The repair was super easy and the part worked like a charm. I love my new ice maker! I had to take out the top freezer shelf just so I could fit my head in the freezer to find one screw, but otherwise all went fine. Ice maker is held on with two top screws and one bottom screw. Loosen the two top screws, remove the bottom screw and li
... Read more
ft out the ice maker. It plugs into wires on the inside, back of the freezer so this has to be unplugged. Plug in the wires for the new one, slide it down onto the two top, loose screws, tighten those and screw in the bottom one, replace freezer shelves and you are ready for ice...with no huge iceberg fouling up the ice in your ice cube tray. Simple! The wiring thing worried me when others described it, but it's no harder than plugging in a lamp, really. If I can do it, anybody who can stand on a shorty ladder can do it.
Read less
Was this helpful?
Thank you for voting!
Broke the arm off the food compartment rocker switch
-
David from St. Pete Beach, FL
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips
... Read more
were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Read less
Was this helpful?
Thank you for voting!
ice maker would not make ice.The fill tube had seperated and iced up so no water could get to ice maker
-
Thomas from newark, DE
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Just followed the video that you guys had on line . It was a very easy repair
Was this helpful?
Thank you for voting!
ice maker not making ice
-
judi from wallowa, OR
- Easy
- 15 - 30 mins
-
Screw drivers
repair went well. Ice maker still not making ice. UGH
Was this helpful?
Thank you for voting!
Would not make ice
-
Roy from Denver, CO
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
It started out being a disappointment. I just moved into a new place that needs many repairs so I didnt want to spend too much time on this one. I ordered this part which arrived in just a few days. Not knowing exactly what was broken I just ordered the whole thing. When I opened the box, the first thing I noticed was that one of the
... Read more
parts of the new ice maker had a big crack in it. Not wanting to go through the hassle of boxing it up and going through the return process, I started taking it apart and replacing the worn or broken owned, (exactly why I ordered the entire unit). Nevertheless, I wanted ice so I fixed it with some of the new ones and some of the old ones. By now I've paid too much for the unit but it was my choice not to send it back and I now have ice. It was pretty easy to fix once I had the parts.
Read less
Was this helpful?
Thank you for voting!
ice maker water fill tube cracked
-
michael from spring, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
hardest part was pulling out the refrigerator. it took about five minutes. parts fit perfectly. only thing to look for is some excess flashing on the end of the tube. easily removed with a pocket knife. simple repair.
Was this helpful?
Thank you for voting!
Light switch went bad
-
Joseph T. from Morgantown, WV
- Really Easy
- Less than 15 mins
Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th
Was this helpful?
Thank you for voting!
No light in frig
-
Irene from Whitehall, MT
- Really Easy
- Less than 15 mins
We tried repairing with a new switch which was very easy to install but it didn't fix the problem.
Was this helpful?
Thank you for voting!
Water fill tube was broke at the 90° in back of the frige
-
Douglas from Pahrump, NV
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Water was already off. All I had to do was pull the fridge away from the wall, remove two screws that hold the fill tube onto the back of the frige, then remove the fill tube. Install the new fill tube, reinstall the two screws. Had to cut the water line straight and clean, slip on the new Compression nut and farrell and insert into the n
... Read more
ew fill tube, tighten-up, good-to-go.
Read less
Was this helpful?
Thank you for voting!
fill tube broken at elbow
-
Jack from Houston, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
Moved the refrigerator out, unscrewed old fill tube, pulled it out, placed finger-screw on water line, screwed it on, put in new fill tube, re-screwed fill tube in place, put refrigerator back into place. Done!
Was this helpful?
Thank you for voting!
Light switch which turns on the lights when the door opens went out
-
Dennis from Lawrenceville, GA
- Really Easy
- Less than 15 mins
-
Nutdriver
This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.
Was this helpful?
Thank you for voting!
Refrigerator cooling fails to come back on after defrost cycle.
-
Donald from Seattle, WA
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Since the defrost timer turns the cooling functions on and off for each defrost cycle if seemed the most likely problem. That was confirmed by manually advancing the timer with a screw driver and the cooling functions would resume and run until the next defrost cycle (every 8 hours or so). The repair itself was to swap out the timer whi
... Read more
ch took five minutes with a #2 phillips screw driver and a 1/4" nut driver. Once the timer was removed from the cover plate there's a simple plug-in connector to remove from the old and plug into the new timer. Two machine screws hold the timer in place behind the cover plate. Be sure switch the power off on the compressor cabinet before removing the cover plate.
Read less
Was this helpful?
Thank you for voting!
Water ran all over freezer froze many times. Hair dryer to melt, Desaster!
-
Thomas A from SAN DIEGO, CA
- Really Easy
- Less than 15 mins
-
Socket set
Watched your AMAZNG detailed Video first. Ordered part received in two days,WOW! Pulled refrig. from wall unscrewed two screws, loosened third screw on hose, pulled hose out cut below metal incert. Took new part from package placed in back of refrig. placed new metal incert in hose replaced hose in new fitting. Turned water back on, plug
... Read more
ged in refrig. No leaks pushed back to wall waited for while...VOILA!! ice cubes no mess to report. THANKS FOR SUCH AN AMAZING WEB SITE and SERVICE. TOM
Read less
Was this helpful?
Thank you for voting!
light switch sticking
-
Paula from Rush, NY
- Easy
- Less than 15 mins
-
Pliers, Screw drivers
I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.
Was this helpful?
Thank you for voting!