1069334310 Kenmore Refrigerator - Instructions

I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.

Followed a youtube diagnostic video on a whirlpool fridge with the same configuration. After determining that the problem was the thermostat I ordered the part from parstselect. I was pleasantly surprised by both the fair shipping price and the 2 day arrival. Replacement was as simple. Cut the old wires, wire nut the new ones. Wire c ... Read more olors are the same on my old unit and the replacement, but these generally aren't polarized anyways.

Very easy to replace. Disconnect water line. remove 2 screws pull out filler tube. replace with new one.

Moved the refrigerator out, unscrewed old fill tube, pulled it out, placed finger-screw on water line, screwed it on, put in new fill tube, re-screwed fill tube in place, put refrigerator back into place. Done!

hardest part was pulling out the refrigerator. it took about five minutes. parts fit perfectly. only thing to look for is some excess flashing on the end of the tube. easily removed with a pocket knife. simple repair.

I did remove the run capacitor of the starthing kit of compressor and another one new. It work fine.

Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th

I looked for the obvious sign of malfunction, a leak lack of air flow dirty coil finding nothing obvious I checked the electrical components and the first was the start relay with a bimetal temperature switch was the problem that was identifyed when removed due to the relay sounding like it was internally damaged because of severe ratelin ... Read more g

I was careful to unplug each cord one at a time so that I can easily match them up to the new start relay. Once I got the cords plugged into the new start relay, I went ahead and plugged in the fridge and it worked like it never stopped working. I must admit, I'm still nervous about this fridge because I never had to do anything like this ... Read more in my life so in the back of my mind, I'm always wondering if I did it correctly or not. I was giving a lesson on how to make sure that I have it on correctly but that didn't put me at ease..lol. Parts Select sent this part in less then a day and that made me appreciate there business even more. I was concerned that the part wouldn't get here until later on that week.

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

Water was already off. All I had to do was pull the fridge away from the wall, remove two screws that hold the fill tube onto the back of the frige, then remove the fill tube. Install the new fill tube, reinstall the two screws. Had to cut the water line straight and clean, slip on the new Compression nut and farrell and insert into the n ... Read more ew fill tube, tighten-up, good-to-go.

took out the old fill tube installed the new one and its working great. I really did not think that was going to be the problem thought it would be more than that but it was not. It took about 7min to change thanks for the fast shipping I will use you in the future.

First thing, I didn't have any idea how to fix my refrigerator, but I saw some videos on line, I just pull the start relay, it sound like little parts inside. I order to PART SELECT my Start Relay combination and part select have more comments, diagrams it was easy to find the part. Put the new start relay was easy, I just conect those wi ... Read more res back it took less than 10 minutes and it's working now.thanks to Part Select to make easy to fix it.

Removed screws from the back of the part in the fridge. Pulled old part out. Measured the old part. Cut new part to fit. Replaced new part and tightened the screws. Worked perfectly.

Viewed the viedo - it showed what to do