- Home
- 1068782880
- Instructions
1068782880 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
ice maker quit
3 of 4 people
found this instruction helpful.
-
Tim from Ewing, NJ
- Really Easy
- 15 - 30 mins
-
Socket set
i noticed that no water was getting to the ice maker. rather than messing around with parts, i bought the entire unit. easy to remove old one and install new one. thanks...ice started again in about an hour. unit cost less than a service call!
Was this helpful?
Thank you for voting!
the light socket broke apart
4 of 7 people
found this instruction helpful.
-
Elyse from Skokie, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers
I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.
Was this helpful?
Thank you for voting!
Refrigerator quit cooling and the freezer wasn't freezing anything
4 of 7 people
found this instruction helpful.
-
Tonya from Grand Prairie, TX
- Really Easy
- 15 - 30 mins
-
Socket set
Order the part from the Internet on Sunday, it mailed out on Monday and I received it on Tuesday. I unplugged the fan then undone 3 screws that held the fan bracket to the refrigerator pulled it out unscrewed 3 more nuts and replaced the fan on the bracket and I cut the old wire plug off the old fan and with 2 wire nuts put it on my new f
... Read more
an. Replaced the fan and bracket back on the refrigerator plugged it in and it works like a new refrigerator.
Read less
Was this helpful?
Thank you for voting!
Cracked Icemaker Water Fill Tube
4 of 7 people
found this instruction helpful.
-
James from Ft. Lauderdale, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
The plastic part that connects the fresh cold water to the ice maker in back of the fridge cracked.
Do to the fact that Whirlpool has the part stick out on the back top part of the fridge. So if you push the fridge just an inch too far back the plastic part will crack.
I ordered (The Part S&H)- came to about, $11.00.
... Read more />1. Turned off the cold water under the sink.
2. In the back of the freezer section. I unscrewed the two screws that held the old broken part to the fridge.
3. I opened the freezer section and cleared out the top shelf till I could see the back of the fridge.
4. I removed the old plastic part by pushing & wiggling it about forward and it then extended out the back of the freezer side and then I pulled it out the back and it came out.
5. I slid the new replacement part in basically the reverse of step 4.
6. I connected the hose in the back. To the new, replacement plastic part, that fills the automatic ice tray with water.
7. Once finished I glued a small 2”x2” piece of wood next to the new part so the fridge will never get too close to the back wall so to never break that part that sticks out again.
Before just a small bump could break the part and water is everywhere and this leak could happen slowly at first and the next day what a mess.
Some fridges have this part recessed into the back of the fridge so this would never happen as my other fridge has.
Also, this might seem like more work then it was. It was very simple. I was scared I'd screw it up, but just did it step by step. If I had someone do it. It would have cost me a bundle.
It took more time to type this, then to do the work.
I had no instructions to follow, but again, was easer then I thought it would be.
I hope that this was helpful,
Jim Vourakis
Do to the fact that Whirlpool has the part stick out on the back top part of the fridge. So if you push the fridge just an inch too far back the plastic part will crack.
I ordered (The Part S&H)- came to about, $11.00.
... Read more />1. Turned off the cold water under the sink.
2. In the back of the freezer section. I unscrewed the two screws that held the old broken part to the fridge.
3. I opened the freezer section and cleared out the top shelf till I could see the back of the fridge.
4. I removed the old plastic part by pushing & wiggling it about forward and it then extended out the back of the freezer side and then I pulled it out the back and it came out.
5. I slid the new replacement part in basically the reverse of step 4.
6. I connected the hose in the back. To the new, replacement plastic part, that fills the automatic ice tray with water.
7. Once finished I glued a small 2”x2” piece of wood next to the new part so the fridge will never get too close to the back wall so to never break that part that sticks out again.
Before just a small bump could break the part and water is everywhere and this leak could happen slowly at first and the next day what a mess.
Some fridges have this part recessed into the back of the fridge so this would never happen as my other fridge has.
Also, this might seem like more work then it was. It was very simple. I was scared I'd screw it up, but just did it step by step. If I had someone do it. It would have cost me a bundle.
It took more time to type this, then to do the work.
I had no instructions to follow, but again, was easer then I thought it would be.
I hope that this was helpful,
Jim Vourakis
Read less
Was this helpful?
Thank you for voting!
The water fill tube 90 fitting broke
3 of 4 people
found this instruction helpful.
-
Scott from Crete, IL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Removed brokent tube fitting from the compression nut.
Removed two screws holding the fill tube. Removed and replaced the fill tube. Direct replacement, no cutting tube length. Reconnect water line to the new fill tube.......Done.
Removed two screws holding the fill tube. Removed and replaced the fill tube. Direct replacement, no cutting tube length. Reconnect water line to the new fill tube.......Done.
Was this helpful?
Thank you for voting!
heating element going bad
4 of 7 people
found this instruction helpful.
-
James from Bakersfield, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver
I removed three sheet metal screws, unsnapped the electrical pigtail. Then snapped out knock out on new maker. Matched the electrical connection, pushed it in place. Finally set new one in place, leveled it, tightened the scews and walked away.
Was this helpful?
Thank you for voting!
Ice maker working with no production of ice
2 of 2 people
found this instruction helpful.
-
Paul from East Northport, NY
- Really Easy
- 15 - 30 mins
-
Socket set, Wrench (Adjustable)
Turn off the water source and unplug freezer. Remove copper tube and then remove valve from back of refrigerator. Disconnect plastic tube and power connection. Mark power connection plug top with a "T", this reminder helps with the new valve. Plug power and plastic tube into new valve and screw assembly back into refrigerator. Using a
... Read more
wrench, connect copper tube into valve. Restore water source and plug back in in freezer. Within a couple hours, ice production was back.
Like the other repair stories (that helped me), this job was very easy.
Like the other repair stories (that helped me), this job was very easy.
Read less
Was this helpful?
Thank you for voting!
freezing water tube and frozen rotation bar whuch caused water to overflow and freeze inside freezer.
3 of 5 people
found this instruction helpful.
-
Donna from CUMBERLAND, RI
- Really Easy
- 15 - 30 mins
-
Nutdriver
put arm up to stop icemaker from creating new ice cubes. us nut driver to unscrew 3 of the nuts holding icemaker in place do not completely remove the 2 top screws. lift off the screws and unplug from inside wire connection...make sure water tub is removed and frig unplugged. clean off ice anywhere inside freezer...take out new icemake
... Read more
r and connect wire plug...attach icemaker on to the 2 top screws...use nut driver to tighten into place. add and tighten bottom screw...leave arm down...replace clean and dried water tube into back and make sure it slid into ice maker...tighten screws in back and attatch water hose to tube...plug frid back on slide back into place...will start making ice in an hr or so....
Read less
Was this helpful?
Thank you for voting!
Ice Maker started acting up
2 of 2 people
found this instruction helpful.
-
Bill from Sumas, WA
- Easy
- 15 - 30 mins
-
Nutdriver
I removed the 2 screws on top and the one screw underneath holding the Ice Maker to the wall of freezer.I pulled the electrical connection from the wall next (wiggled it back and forth until it came out).
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts ... Read more to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts ... Read more to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks
Read less
Was this helpful?
Thank you for voting!
Ice Maker Not Creating Ice Cubes
2 of 2 people
found this instruction helpful.
-
Daniel from Albuquerque, NM
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Removed Ice tray and flap followed by the three screws that held the old ice maker in place. (I probably didn't have to remove the top two, they are designed to just loosen and lift up on the mecanism to free.) I then pulled the old wiring harness out of the original ice maker. A small screw driver helped in depressing a tab while pulling
... Read more
on the harness. The same process was used to remove the wiring harness that was attached to the new replacement unit. I connected the original wiring harness that I had disconnected from the bad ice maker, and it fit perfectly into the replacement unit. No need to splice or use any of the harnesses that came with replacement. I tried installing the new unit and discovered that there was interfernce with the water feed hose. I had forgotten to break off the tab on the end of the replacement unit. Once I did that using pliers, the unit fit fine. I tightened the screws, installed the on/off mecanism and replaced the tray and flap. I then waited and waited, hoping to hear the forgotten sound of water entering the ice maker. Had a beer and walked the dogs thinking I had failed, but low and behold, over an hour later, the ice maker turned on the water. Many hours later, my wife woke me up in the middle of the night to declare we had cubes! Success.
Read less
Was this helpful?
Thank you for voting!
Bad fan motor
3 of 5 people
found this instruction helpful.
-
Mark from Farmington Hills, MI
- Easy
- 15 - 30 mins
-
Nutdriver
Pop off six mounting screws and the ground screw. Remove the fan blade and reattach. Reinstall. Save yourself big bucks.
Was this helpful?
Thank you for voting!
Fan was noisy - bearing had failed
2 of 2 people
found this instruction helpful.
-
Karl from Wellesley, MA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.
Was this helpful?
Thank you for voting!
Ice maker quit, I cross wired the two solenoid valves and determined the valvles were not the problem.
2 of 2 people
found this instruction helpful.
-
michael from naples, FL
- Easy
- Less than 15 mins
-
Nutdriver
Used a nutdriver and removed the lower mount nut, then loosened the the top two nuts and the icemaker lifted off, then unplugged the device and replugged it into the "old" plug(the new ones were not needed) then remounted it. Then it did not fill (as others posted happened right away.) Some poster suggested manually filling the tray so I
... Read more
did it. Later it froze and emptied and refilled and started working normally. Not sure if putting water had anything to do with it or it just took some time. It would be nice if the instructions addressed this issue.
Read less
Was this helpful?
Thank you for voting!
Stopped making ice. Black stuff coming out on ice
2 of 2 people
found this instruction helpful.
-
Paul from Navarre, FL
- Easy
- Less than 15 mins
-
Nutdriver
First I removed the (3) screws holding the unit to the side of freezer wall with a nutdriver. Then I disconnect the Harness from the back of the freezer. You have to work the Harness off connector because it was very tight. The Unit came with the correct harness installed so I reconnected the harness to the Freezer and replaced the (3) sc
... Read more
rews. I had ice in about 2.5 hours.
Read less
Was this helpful?
Thank you for voting!
fridge door switch did not work
2 of 2 people
found this instruction helpful.
-
stu from richmond, VA
- Easy
- Less than 15 mins
-
Socket set
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this helpful?
Thank you for voting!