1068782870 Kenmore Refrigerator - Instructions

All Instructions for the 1068782870
121 - 135 of 564

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice maker needed to be replaced as it quit working.
3 of 4 people found this instruction helpful.
  • Ronald from Henderson, NV
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Loosened two top screws using a hand held mirror and screwdriver and removed a bottom screw then unplugged the unit inside. Five minutes and repair was complete. Easy as that!
Was this helpful?
Thank you for voting!
replaced non-functional ice maker
3 of 4 people found this instruction helpful.
  • Richard from Troy, MI
  • Easy
  • Less than 15 mins
  • Nutdriver
After first unplugging the refrigerator from it's electrical power source,I removed the lower screw of the ice making unit with a nut driver. I then loosened the upper two screws which hold the retainer clips that secure the unit tight to the freezer wall. I then lifted the unit upward and outward a few inches to allow access to the wire harness. I unplugged the haness from rear of the freezer and removed the unit completely.
To install just reverse the procedure.
Was this helpful?
Thank you for voting!
ice tray leaking
9 of 22 people found this instruction helpful.
  • Linda from Santa Maria, CA
  • Really Easy
  • Less than 15 mins
Super! It was so fast and easy to fix. Receive my kit in three days and save a lot of money not having to have a repairman come and do it!
Was this helpful?
Thank you for voting!
defective light switch
3 of 4 people found this instruction helpful.
  • THOMAS from WILLARD, OH
  • Really Easy
  • Less than 15 mins
inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
Was this helpful?
Thank you for voting!
Unit would not cycle and dispense ice. After replacing with new unit I disassembled old unit and detected a slight burn smell in the timer.
3 of 4 people found this instruction helpful.
  • Robert from Tucson, AZ
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Unplugged refrigerator and turned off water supply. Loosened two top screws and removed bottom screw. Althought kit was supplied with multyple wiring harnesses the harness attached to unit was the correct harness for the model I was replacing. Removed and reused old shut off arm as replacement arms were shorter in reach then original. Also reused bottom unit support that was removed and replaced with one screw into unit and then into side wall of freezer. Over all time less then 15 minutes. As this was a side by side ref/freezer unit their us limited space to view support screws. I used a mechanics mirror to find upper screws. This visualization made the process go much faster. Reading the other repair stories also gave me a huge confidence boost and insite in what to expect.
Was this helpful?
Thank you for voting!
Water fill tube broken
3 of 4 people found this instruction helpful.
  • Jeffrey from Monroe, MI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
removed two screws and pulled part out of the unit. The local appliance store said they needed model and part # to try to identify and order the part. Found part select online, found the part immediately, ordered the part for $4.50 or so. Part was delivered in 2 days! Very easy installation and the part works perfectly. Thanks so muc h!
Was this helpful?
Thank you for voting!
The ice maker stopped making ice
2 of 2 people found this instruction helpful.
  • Terry from Felton, PA
  • Really Easy
  • Less than 15 mins
  • Socket set
I removed the two attachment screws and lifted the old icemaker out and disconnected the plug. The new one was identical to the old one so the installation was just a reversal of the removal. The water soleniod was sticking from not being used so I took it apart and cleaned it. The next morning I had ice. The part arrived at my door in le ss than 24 hours from my order placement.
Was this helpful?
Thank you for voting!
Ice maker failed
2 of 2 people found this instruction helpful.
  • Kim from Palo Alto, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Super easy! I read all these posts but here are a couple helpful hints -

1. to remove the old icemaker definitely remove the one lower screw but then unscrew the top two screws only half way. The top screw holes on the old and new icemakers are triangle shaped so the old icemaker will simply lift off the half-unscrewed top scr ews. This makes reinstallation SO much easier.

2. carefully lower the loose icemaker enough to disconnect the wiring harness from the fridge and remove the old icemaker.

3. On installation the one thing to be careful with is the positioning of the fill tube. It's easier if it's in place when you reconnect the harness of the new icemaker because the harness is only as long as it must be.
4. hang the new icemaker on the half unscrewed top screws, snug them up, install the lower screw and flip the wire ice level sensor arm down.

I didn't even turn the water off because only a working icemaker can turn the water valve on and off.

Plugged in the power to the fridge and within an hour water filled the tray. By morning I had 2-3 batches of fresh ice in the bucket. Super easy.
Was this helpful?
Thank you for voting!
Unit froze up with ice in the cube maker
2 of 2 people found this instruction helpful.
  • John from Mesa, AZ
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Just like the others. Unplug the refrigerator. Loosen the top two screw and remove the bottom screw. Unplug the unit, plug in the new one, slid the unit over the top two screws, replace the bottom screw and tighten the top two screws. Done. I ordered the unit Sunday it was shipped Monday and arrived Phoenix Wednesday, shipper then re routed it to Tucson Thursday who sent it back to Phoenix on Friday and finallydelivered it Saturday.
Was this helpful?
Thank you for voting!
The ice maker quit producing ice.
2 of 2 people found this instruction helpful.
  • Robert from Spring Valley, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
First I removed the ice bin to give me room to work. Then I took out the screws that held the old ice maker in place. I disconnected the wiring. I then plugged the wires of the new ice maker into the old wiring harness. I put in the bottom screws and loosely connected the top screws. I checked the level of the ice maker with a small l evel and then tightened the screws. The nest thing was to install wire level that shuts off the ice maker when the bin is full. Finally put the ice bin back in place.
Was this helpful?
Thank you for voting!
fridge door switch did not work
2 of 2 people found this instruction helpful.
  • stu from richmond, VA
  • Easy
  • Less than 15 mins
  • Socket set
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.
Was this helpful?
Thank you for voting!
Ice maker quit. Got water out of ice dispenser
2 of 2 people found this instruction helpful.
  • Melvin from Girard, IL
  • Really Easy
  • Less than 15 mins
  • Socket set
Wathced video (VERY helpful)of how to do repair to make sure it was within my capabilities to do. Made sure I had all requested numbers before ordering. Replacement part was an EXACT fit. 15 minutes of work and I saved nearly $150 of estimate by local service company. I am (and will continue to be) a repeat customer. Thanks. Mel
Was this helpful?
Thank you for voting!
Door light switch disintegrated
2 of 2 people found this instruction helpful.
  • Thomas from Roseville, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Very simple fix, remove 3 screws, two connectors to the old switch
Was this helpful?
Thank you for voting!
Ice maker went bad
3 of 5 people found this instruction helpful.
  • DENNIS from SOUTH LYON, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Took the old one out in Two Min's, Replaced with the new one in about the same time.
Had ice within 1 hour
Was this helpful?
Thank you for voting!
Light didnt go on
3 of 5 people found this instruction helpful.
  • dorotea from staten island, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this helpful?
Thank you for voting!
All Instructions for the 1068782870
121 - 135 of 564