1068782830 Kenmore Refrigerator - Instructions

All Instructions for the 1068782830
91 - 105 of 564

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice Maker didn't produce ice cubes.
4 of 5 people found this instruction helpful.
  • Michael from Long Valley, NJ
  • Easy
  • 30 - 60 mins
  • Nutdriver
It was not complicated but it took more squeezing and reaching into the narrow space than actually removing three screws and unplugging the electrical harness. But that was all that was necessary, to install, three screws held the unit in place and re-connect the electrical harness. It saved me about $100 in labor and the inconvenience of scheduling a service call and waiting for a week or so. The best part was that I ordered the unit on line on Tuesday eveining and it was at my home by Friday afternoon with no extra shipping charges. Great service!.
Was this helpful?
Thank you for voting!
Evaporator Fan in Freezer Making Load Noise
4 of 5 people found this instruction helpful.
  • Ralph from SAINT PAUL, MO
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Removed freezer shelving. Removed 3 shelving brackets (dovetailed) by sliding them up off of the small square mounted on the freezer wall. This was a stumbling block until
I figured out how to remove these brackets. Removed three Philips head screw in freezer back panel (24) with nut driver. Removed light bulb cover to get some grip on back panel. Lifted the back panel up slightly and then folded in down a bit then rotated it to the left. Removed 4 hex head (1/4in) screws on fan shroud (23) and brought down into the freezer. Disconnected electrical spade connectors from motor and removed entire unit from freezer to work on motor. Removed two hex head screws (18) holding motor to the brackets. Pushed new fan on to new motor using a 1/4 nut driver and hammer. Mounted motor to old brackets with two screws (18). Placed motor/fan/shroud unit in freezer and reconnected electrical spade connectors. Replaced motor/fan/shroud in freezer with the 4 hex head screws (15), dropping one behind the coils. Just replaced it with a look alike. Turned power back on to check if the fan was operating normally. Put back panel in place and screwed it in place then put shelving clips back into place and then all the shelving. Appears to operating quietly so far. About 30 minutes to complete the job.
Was this helpful?
Thank you for voting!
Installing old ice maker in new freezer
3 of 3 people found this instruction helpful.
  • Harry from Ten Mile, TN
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I was able to transfer my old ice maker from my old Roper Refrigerator/Freezer into my new Whirlpool Sidekick Freezer. Everything transferred directly except for the water fill tube. I ordered one on line and simply cut it to the right length, removed the cover plate inside the freezer compartment and the little sticker from the outside. Inserted tube and fastened in place with two screws (not provided but was able to use the screws that were in the holes inside the freezer before the ice maker went in. Works great. By not buying the ice maker with the freezer I saved a hundred bucks or so.
Was this helpful?
Thank you for voting!
Fan motor
3 of 3 people found this instruction helpful.
  • Bonnie from DETROIT LAKES, MN
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Remove bottom of freezer by sliding out the gaskets on each side.

Remove back of freezer. 6 screws.

Remove fan cover. 4 screws.

Remove fan. 3 wires to disconnect. 2 screws to take out.

Install the fan. Connect the 3 wires. Fastened with 2 screws.
Put fan cover back on. 4 screws. ... Read more >Put back of freezer back on. 6 screws.
Put bottom of freezer back in. Slide gaskets in on each side.
Was this helpful?
Thank you for voting!
Icemaker motor quit
3 of 3 people found this instruction helpful.
  • David from Selma, IN
  • Easy
  • 15 - 30 mins
  • Nutdriver
This was a snap. Loosened 3 screws, removed
old ice maker. Made cutout for water chute. Plugged in
wiring harness plug. Installed new ice maker. Tightened 3 screws.

These brain surgeons that charge $80.00 just to show up at my house to repair an appliance are history.
Was this helpful?
Thank you for voting!
lights wouldn't come on/work in refrigerator
4 of 6 people found this instruction helpful.
  • Jane from Albuquerque, NM
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80.. .would have been at least $100 to have a repair person come to the house!
Was this helpful?
Thank you for voting!
Noisy freezer evaporator fan motor
4 of 6 people found this instruction helpful.
  • Lloyd from Long Beach, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Removed the shelves from the freezer and the brackets holding it along with the covers for the light and plate for the ice maker (we don't have one). Pulled the ground wire from the tab off the port for the ice maker. Removed back plate exposing the fan motor and then the 4 hex screws holding on part #23 of the diagram which the fan mot or is mounted to. Flipped it over, unscrewed the 2 hex screws from the fan motor mounting and removed it. Removed and replaced 3 wire connectors on new fan motor. Installed new fan motor and new grommets but used the old screws because the provided screws were larger. Pushed the new fan on to the motor shaft. Reassembled. Half hour most.
Was this helpful?
Thank you for voting!
Fan was making alot of noise
4 of 6 people found this instruction helpful.
  • JERRY from ALBION, AL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
I removed all the shelves and the back shelf hanger. Removed two screws on the back plate.Pulled it out.Removed the screws that hold the fan housing. Pulled it out so I could write down the three wires color and location.Unpluged them.Removed the old fan and installed the new one.and put everthing back together.
Was this helpful?
Thank you for voting!
Replaced broken shelf supports
4 of 6 people found this instruction helpful.
  • Cheryl from Los Angeles, CA
  • Really Easy
  • Less than 15 mins
Took out old pieces and popped new ones in, just like that!
Was this helpful?
Thank you for voting!
Raplaced switch
5 of 9 people found this instruction helpful.
  • Winston A from Brooklyn, NY
  • Really Easy
  • Less than 15 mins
  • Pliers
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Was this helpful?
Thank you for voting!
water dripping in ice cube holder
4 of 6 people found this instruction helpful.
  • Christine from Clarkston, MI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
We removed three screws, unplugged the wire and then removed the old ice maker. Installed the new ice maker with the screws, plugged in the wire and shortly after that we had ice! I was nervous about this repair but it was so easy and the part was here in three days.
Was this helpful?
Thank you for voting!
Would not make ice any longer
4 of 6 people found this instruction helpful.
  • James from Concord, MA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I determined that the ice cube maker was no longer heating the cubes so they could be released into the ice tray. After ordering a new unit, taking out four screws and disconnecting the quick disconnect of wires I plugged the new one in and we were back in business.
Was this helpful?
Thank you for voting!
Compressor making excessive noise
5 of 9 people found this instruction helpful.
  • chester from Tampa, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
One front roller was flat on one side. Decided to replace all rollers at same time. Placed shims under unit and removed mounting screws for one front and one rear roller. With new rollers in place, I was able to level the refrigerator side to side, but unable to do so, front to back. Left the new front roller in place and reinstalled the old rear roller. Have decided to replace refrigeratorin the near future. This is one of my few repair failures!
Was this helpful?
Thank you for voting!
The ice maker only make two cubes of ice per tray
3 of 3 people found this instruction helpful.
  • Clinton from EUSTIS, FL
  • Really Easy
  • 30 - 60 mins
I replaced the old icemaker with a new one but the problem is still occurring in the new one. It only fill with enough water to make about two ice cubes
Was this helpful?
Thank you for voting!
defective light switch
3 of 4 people found this instruction helpful.
  • THOMAS from WILLARD, OH
  • Really Easy
  • Less than 15 mins
inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
Was this helpful?
Thank you for voting!
All Instructions for the 1068782830
91 - 105 of 564