- Home
- 1068740921
- Instructions
1068740921 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Making a god awful racket.
5 of 7 people
found this instruction helpful.
-
Michael from Locust Grove, VA
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Ok its the garage "adult " Beverage chiller.
Easy fix First I removed the 4 screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires assembly was the reverse. and the beverages never got warm..
Easy fix First I removed the 4 screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires assembly was the reverse. and the beverages never got warm..
Was this helpful?
Thank you for voting!
Ice maker was leaking
6 of 10 people
found this instruction helpful.
-
Thomas from San Diego, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
This is an incredibly easy repair.
1) Remove the three screws holding the old icemaker
2) Disconnect the electrical connection (I used a spoon to get in and undo the connector clip
Do the opposite to install the new icemaker.
Total elapsed time was about 5 minutes.
1) Remove the three screws holding the old icemaker
2) Disconnect the electrical connection (I used a spoon to get in and undo the connector clip
Do the opposite to install the new icemaker.
Total elapsed time was about 5 minutes.
Was this helpful?
Thank you for voting!
would shut off and not restart without tapping on knob
4 of 4 people
found this instruction helpful.
-
Brad from RAINIER, OR
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
replaced the cold control thermostat . The new one was oriented 90 degrees off (on the bracket mount) so I had to turn it (in the bracket) to line up better with the wire connections and temp sensor tube. The power wires can be connected to either terminal however, and I suppose you could leave it as is if your wires can reach. Turning it
... Read more
will make the knob off 90 deg. off from original markings (off to coldest) but I simply remarked the position with a marker. (make sure you connect all terminals before mounting the bracket, it's much easier that way. .Note: this was a 40+ year old Sears "Coldspot" refridg. and it works like a dream since I changed out this original cold control. Love these old mechanical appliances that are much more reliable than the new brokered ones. Glad whirlpool has made many parts interchangeable through many years...kudos to them
Read less
Was this helpful?
Thank you for voting!
My U-line ice maker quit filling.
5 of 7 people
found this instruction helpful.
-
Anne from Arlington, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I used this part on a little, under-counter U-line ice maker that is the best little ice maker in the world. The single solenoid part from U-line cost more than twice as much as the generic GE one I ordered from you. It arrived in only 2 days and I was able to just remove the inlet and outlet line from the old solenoid and unscrew the bra
... Read more
cket to remove it. I used the included bracket and one screw affix the new one to the ice maker, then just pushed on the inlet and outlet lines, tightened them on, plugged it back in and In about 20 minutes from start to finish, it was back in business, cranking out ice really quick as it was before. Could not imagine summertime in Texas without my U-line,,,Thank you!!!
Read less
Was this helpful?
Thank you for voting!
Removed the old parts then connected the new parts.
4 of 4 people
found this instruction helpful.
-
Jonathan from OLIVE BRANCH, MS
- Really Easy
- 30 - 60 mins
-
Screw drivers
The compressor immediately started when I plugged the refrigerator back in. Around 24 hours later the freezer compartment was at 0 degrees, and the refrigerator was at 35 degrees.
Was this helpful?
Thank you for voting!
water was leaking under the frig ,wasnt sure what the problem
4 of 4 people
found this instruction helpful.
-
stephen from ROCKLEDGE, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
decided to take a chance and replace the ice maker,so far no water leaking.feels nice to know the problem is fixed.thanks for the video on how to replace it, thanks again very easy repair
Was this helpful?
Thank you for voting!
Freezer making loud whining noise-Fridge not cooling well
7 of 13 people
found this instruction helpful.
-
Dale from Blaine, MN
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Removed the 3 screws in the back of the freezer, pulled back the metal back plate on the freezer. Removed 4 nuts on the plastic housing that holds the fan and pulled the housing down. Disconnected the wires, unscrewed the 2 screws holding the fan to the housing. Replaced old fan motor with new fan motor onto housing just as it was befo
... Read more
re. Reconnected the wires. And tested the motor. Worked great. Re-assembled everything as it was and it was done.
Read less
Was this helpful?
Thank you for voting!
Refrigerator light would not turn on.
5 of 8 people
found this instruction helpful.
-
Suzanne from STERLING HTS, MI
- Really Easy
- Less than 15 mins
-
Nutdriver
I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom.
... Read more
The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.
Read less
Was this helpful?
Thank you for voting!
Filler tube broken and old tube frozen over
4 of 5 people
found this instruction helpful.
-
Alan from Chino, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
this is a snap! 2 screws an a nut to tighten and it works like a charm. the filler tube in my Kenmore refer had broken off in the back. ( really bad location to put this in the beginning) if you push the refer to close to the wall you can break it off easily. remove the water line by loosing the nut and remove the hose from the fill tube
... Read more
( This assumes you have already turned of the water supply or you are standing in a large puddle)remove the 2 screws that hold the filler tube in place. pull out the old filler tube in and slightly upright motion. replace the new fill tube into the same hole and replace the screws. replace the hose and tighten the nut, turn the water back on and check for leaks your done !!
doesn't that feel great?
doesn't that feel great?
Read less
Was this helpful?
Thank you for voting!
Ice maker did not work
4 of 5 people
found this instruction helpful.
-
Judy from Galveston, IN
- Easy
- Less than 15 mins
-
Nutdriver
Took the old one out and plug the new one in, simply as 1 2 3. Order the part one morning,it was here the next afternoon, the ice maker was fixed in less than a half hour. we will order from you the next time.
Was this helpful?
Thank you for voting!
Ice maker not working
6 of 11 people
found this instruction helpful.
-
Raoul from Thousand Oaks, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
take out Ice maker tray, remove three screws holding the ice maker, unplug electrical connector. Replace with new Ice maker,Ice started to fill the tray. ENJOY!!
THANKS.
THANKS.
Was this helpful?
Thank you for voting!
Fan motor stopped working.
5 of 8 people
found this instruction helpful.
-
John from Clifton Heights, PA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
I first unplugged the unit.
Secondly I unscrewed the back panel and removed it.
Third, I unplugged the fan, unscrewed it, removed it, and replaced it with the new fan motor.
I then plugged it to confirm that it worked and then put everything back together.
Secondly I unscrewed the back panel and removed it.
Third, I unplugged the fan, unscrewed it, removed it, and replaced it with the new fan motor.
I then plugged it to confirm that it worked and then put everything back together.
Was this helpful?
Thank you for voting!
nosiy fan operation
4 of 5 people
found this instruction helpful.
-
TOM from GRANVILLE, MA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
most of the time spent on repair was removing the food from freezer compartment other than that removal of a couple screws and disconnecting and reconnecting wires not a huge ordeal
Was this helpful?
Thank you for voting!
Broken filler tube at threaded connection
4 of 5 people
found this instruction helpful.
-
Matthew from Phoenix, AZ
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
After discovering that the water noise was coming from the rear of the refridgerator upon pulling it foward I discivered the connection line had broken. So i got a phillips screw driver and removed the the two mounting screws and saw it was one piece. I easliy found the part on PartSelect website and once I got I merely swaped them out
... Read more
and it works good as new!
Read less
Was this helpful?
Thank you for voting!
Ice Maker didn't produce ice cubes.
4 of 5 people
found this instruction helpful.
-
Michael from Long Valley, NJ
- Easy
- 30 - 60 mins
-
Nutdriver
It was not complicated but it took more squeezing and reaching into the narrow space than actually removing three screws and unplugging the electrical harness. But that was all that was necessary, to install, three screws held the unit in place and re-connect the electrical harness. It saved me about $100 in labor and the inconvenience of
... Read more
scheduling a service call and waiting for a week or so. The best part was that I ordered the unit on line on Tuesday eveining and it was at my home by Friday afternoon with no extra shipping charges. Great service!.
Read less
Was this helpful?
Thank you for voting!