1068739421 Kenmore Refrigerator - Instructions

All Instructions for the 1068739421
106 - 120 of 574

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Installing old ice maker in new freezer
3 of 3 people found this instruction helpful.
  • Harry from Ten Mile, TN
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
I was able to transfer my old ice maker from my old Roper Refrigerator/Freezer into my new Whirlpool Sidekick Freezer. Everything transferred directly except for the water fill tube. I ordered one on line and simply cut it to the right length, removed the cover plate inside the freezer compartment and the little sticker from the outside. Inserted tube and fastened in place with two screws (not provided but was able to use the screws that were in the holes inside the freezer before the ice maker went in. Works great. By not buying the ice maker with the freezer I saved a hundred bucks or so.
Was this helpful?
Thank you for voting!
Fan motor
3 of 3 people found this instruction helpful.
  • Bonnie from DETROIT LAKES, MN
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Remove bottom of freezer by sliding out the gaskets on each side.

Remove back of freezer. 6 screws.

Remove fan cover. 4 screws.

Remove fan. 3 wires to disconnect. 2 screws to take out.

Install the fan. Connect the 3 wires. Fastened with 2 screws.
Put fan cover back on. 4 screws. ... Read more >Put back of freezer back on. 6 screws.
Put bottom of freezer back in. Slide gaskets in on each side.
Was this helpful?
Thank you for voting!
Fan was making alot of noise
4 of 6 people found this instruction helpful.
  • JERRY from ALBION, AL
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
I removed all the shelves and the back shelf hanger. Removed two screws on the back plate.Pulled it out.Removed the screws that hold the fan housing. Pulled it out so I could write down the three wires color and location.Unpluged them.Removed the old fan and installed the new one.and put everthing back together.
Was this helpful?
Thank you for voting!
Noisy freezer evaporator fan motor
4 of 6 people found this instruction helpful.
  • Lloyd from Long Beach, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Removed the shelves from the freezer and the brackets holding it along with the covers for the light and plate for the ice maker (we don't have one). Pulled the ground wire from the tab off the port for the ice maker. Removed back plate exposing the fan motor and then the 4 hex screws holding on part #23 of the diagram which the fan mot or is mounted to. Flipped it over, unscrewed the 2 hex screws from the fan motor mounting and removed it. Removed and replaced 3 wire connectors on new fan motor. Installed new fan motor and new grommets but used the old screws because the provided screws were larger. Pushed the new fan on to the motor shaft. Reassembled. Half hour most.
Was this helpful?
Thank you for voting!
lights wouldn't come on/work in refrigerator
4 of 6 people found this instruction helpful.
  • Jane from Albuquerque, NM
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80.. .would have been at least $100 to have a repair person come to the house!
Was this helpful?
Thank you for voting!
water dripping in ice cube holder
4 of 6 people found this instruction helpful.
  • Christine from Clarkston, MI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
We removed three screws, unplugged the wire and then removed the old ice maker. Installed the new ice maker with the screws, plugged in the wire and shortly after that we had ice! I was nervous about this repair but it was so easy and the part was here in three days.
Was this helpful?
Thank you for voting!
Icemaker motor quit
3 of 3 people found this instruction helpful.
  • David from Selma, IN
  • Easy
  • 15 - 30 mins
  • Nutdriver
This was a snap. Loosened 3 screws, removed
old ice maker. Made cutout for water chute. Plugged in
wiring harness plug. Installed new ice maker. Tightened 3 screws.

These brain surgeons that charge $80.00 just to show up at my house to repair an appliance are history.
Was this helpful?
Thank you for voting!
Compressor making excessive noise
5 of 9 people found this instruction helpful.
  • chester from Tampa, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
One front roller was flat on one side. Decided to replace all rollers at same time. Placed shims under unit and removed mounting screws for one front and one rear roller. With new rollers in place, I was able to level the refrigerator side to side, but unable to do so, front to back. Left the new front roller in place and reinstalled the old rear roller. Have decided to replace refrigeratorin the near future. This is one of my few repair failures!
Was this helpful?
Thank you for voting!
The ice maker only make two cubes of ice per tray
3 of 3 people found this instruction helpful.
  • Clinton from EUSTIS, FL
  • Really Easy
  • 30 - 60 mins
I replaced the old icemaker with a new one but the problem is still occurring in the new one. It only fill with enough water to make about two ice cubes
Was this helpful?
Thank you for voting!
Ice maker was leaking and had metal in the ice
3 of 4 people found this instruction helpful.
  • Charles from Newark, DE
  • Easy
  • 15 - 30 mins
  • Nutdriver
Removed the screws and disconnected the electric. I put the proper electric harness on and went to fit the unit in but it didn't fit. Until I figured out that you have to use the clips from the old unit that hold the unit in place. The actually hang on them. Once I figured it out it was easy.
Was this helpful?
Thank you for voting!
Ice maker quit making ice--had to either be a faulty switch in the ice maker or a faulty water valve. I guessed it was the ice maker switch and ended up being correct.
3 of 4 people found this instruction helpful.
  • Harvey from Port Tobacco, MD
  • Really Easy
  • 15 - 30 mins
  • Wrench set
It was exactly as everyone else described--remove old ice maker, unplug, plug in new ice maker, attach new ice maker. 3 screws, 1 plug. My plug was the one on the ice maker not on the refrigerator (ie I used the wiring/plug that was already in the freezer).
Was this helpful?
Thank you for voting!
Refrigerator quit cooling and the freezer wasn't freezing anything
4 of 7 people found this instruction helpful.
  • Tonya from Grand Prairie, TX
  • Really Easy
  • 15 - 30 mins
  • Socket set
Order the part from the Internet on Sunday, it mailed out on Monday and I received it on Tuesday. I unplugged the fan then undone 3 screws that held the fan bracket to the refrigerator pulled it out unscrewed 3 more nuts and replaced the fan on the bracket and I cut the old wire plug off the old fan and with 2 wire nuts put it on my new f an. Replaced the fan and bracket back on the refrigerator plugged it in and it works like a new refrigerator.
Was this helpful?
Thank you for voting!
Fill tube on the icemaker was leaking.Looked at sears repair parts list and part was $62. I found the same part here for $4.99. Very easy to just remove the old part and replace it with the new. I also received the part in two days. Amazing!!!!
3 of 4 people found this instruction helpful.
  • Walton from Woodland, PA
  • Really Easy
  • 15 - 30 mins
  • Pliers
Simlpy removed two screws to remove the old part. replaced the new part and put the two screws in. Job finished.
Was this helpful?
Thank you for voting!
Ice maker was not working.
4 of 7 people found this instruction helpful.
  • Doyle from Winchester, VA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
On my particular model refrigerator I only needed to remove one screw and disconnet the plug. I then slid the unit out. The new ice maker did not come with the plastic sled that was attached to the old unit. I removed and attached the sled to the new unit with 3 screws.
Was this helpful?
Thank you for voting!
Icemaker Died
3 of 4 people found this instruction helpful.
  • Don from Jacksonville, TX
  • Easy
  • 15 - 30 mins
  • Socket set
The instructions are practically no help, but if you study the diagram, you can figure out the one screw you need to remove. Then the icemaker lift off of two brackets. I couldn't see how to use a screwdriver to unlock the bracket, but just applying mild pressure and pulling it forward brought it right out. I didn't have to change anyt hing with the plug already intalled so it was very easy to pop in, lock the plug, pop into brackets, replace screw and I was in business. 24 hours later I had a bucket of ice! 15 minutes to figure out how to get old out and 5 min to replace new one. Fairly easy. Read posts here to get hints!
Was this helpful?
Thank you for voting!
All Instructions for the 1068739421
106 - 120 of 574