- Home
- 1068730833
- Instructions
1068730833 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
stop making ice
7 of 11 people
found this instruction helpful.
-
Ricky from Philadelphia, PA
- Easy
- Less than 15 mins
-
Nutdriver
1.removed 3 nut screws-2 on top &1 on bottom.
2.unplug ref. from outlet.
3.unplug the wires from ice maker to ref.
4.remove ice maker
5.rinse new ice maker
6.plug ice maker to ref. using included wires
7.screw 2 top nut screws first then the bottom.
8.plug ref. back to outlet
9.made first ice in ... Read more about 2-3 hours
2.unplug ref. from outlet.
3.unplug the wires from ice maker to ref.
4.remove ice maker
5.rinse new ice maker
6.plug ice maker to ref. using included wires
7.screw 2 top nut screws first then the bottom.
8.plug ref. back to outlet
9.made first ice in ... Read more about 2-3 hours
Read less
Was this helpful?
Thank you for voting!
The Switch Broke...Absolutely Fell Apart.
5 of 5 people
found this instruction helpful.
-
Duncan from Metairie, LA
- Really Easy
- Less than 15 mins
-
Screw drivers
I simply removed the old switch using 2 small screwdrivers and the old switch case popped out. I then upluged the wires from the old switch and reversed the process. Didn't take longer than 5 minutes begining to end! Thank you for the great service! Duncan quaid
Was this helpful?
Thank you for voting!
In the ice storm in bootheel of Mo the power spiked a few times before it went off. When power came back on, my frige wouldn't stay working. I would have to touch the thermostat to make it cycle back on. Found exact parts on line at partselect needed to repair the fridge. thanks guys!
6 of 8 people
found this instruction helpful.
-
George from Gideon, MO
- Easy
- Less than 15 mins
-
Nutdriver
First I unplugged the appliance, then I took the two screws out that hold the cover over the temp. control knobs,then I removed the cover from the fan and thermocouple probe end. Then I unplugged the two hot wires from the thermostat,and then the ground wire. Then removed the two screws holding the thermostat in place and removed old ther
... Read more
mostat. Installed new thermostat following steps in reverse order.
Read less
Was this helpful?
Thank you for voting!
Refrigerator had shut down
7 of 11 people
found this instruction helpful.
-
Ronald from Martinsville, IL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Went on line ,ordered part on Friday afternoon ,Fedex was at my house Saturday Morning,,THIS SERVICE IS GREAT ,,THANK YOU VERY MUCH FOR BEING SO FAST
Was this helpful?
Thank you for voting!
refrigerator not cooling properly
6 of 9 people
found this instruction helpful.
-
Ernie from Windsor, CA
- Really Easy
- 1- 2 hours
Replaced refrigerator cooling control. No luck. Replaced freezer cooling control. No luck. Coils were icing up. Unplugged frig and allowed coils to defrost. After more poking around, found that condenser fan was not spinning. Touch it and it'd start. That was definitely in need of replacement. Replacement was easy. Refrigerator is
... Read more
now running as it should.
Read less
Was this helpful?
Thank you for voting!
Lower Light Socket removed and Wires capped with wire nuts
6 of 9 people
found this instruction helpful.
-
Wayne from Arlington, TX
- A Bit Difficult
- Less than 15 mins
My tenants moved out of my rental property and abandoned their refrigerator there. The freezer door would not close properly because someone had previously removed the lower door support bracket and failed to replace the lower bracket shim that positions the lower part of the freezer door properly out from the refrigerator cabinet causin
... Read more
g the door gasket seal to bind before the freezer door was fully closed. I removed and replaced this lower door bracket with a new shim made up of serveral thicknesses of cardboard to achieve this spacing and freezer door now closes and seals properly. They had never connected a water supply to the refrigerator although this model is equiped with an ice maker and in door ice and cold water dispenser. The access panel on the back of the unit had been previously removed and discarded. I made up a new access panel from cardboard and connected the water line to the solenoid valve. Valve was so old it would barely open when valve energized and water flow was too slow to make proper sized ice cubes and fill a water glass. I purchased a new water solenoid valve and replaced ther original valve and cured that problem. Replacing the access panel cured an improper cooling problem because with panel removed, most of the air flow bypasses the condenser coils. Lastly I replaced the upper tubular light bulb and the lower light socket I purchased here and installed a 40 watt bulb in the new light socket. Presto! I was able to turn non working abandoned refrigerator into a workable unit.
Read less
Was this helpful?
Thank you for voting!
wasn't making ice. The ice bin actually filled up with water.
5 of 6 people
found this instruction helpful.
-
Bob from Middlefield, CT
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
Removed old valve first, found part # on it.
Entered part # into search box on computer.
It came up with the right replacement part the first time!!!
Ordered part, it came in sooner than I thought it would.
I attached the supply line, pushed in the plastic outlet hose, connected the power line, and attached it to the r ... Read more efrigerator frame. We had a full container of ice the next morning.It couldn't of had been easier.
Entered part # into search box on computer.
It came up with the right replacement part the first time!!!
Ordered part, it came in sooner than I thought it would.
I attached the supply line, pushed in the plastic outlet hose, connected the power line, and attached it to the r ... Read more efrigerator frame. We had a full container of ice the next morning.It couldn't of had been easier.
Read less
Was this helpful?
Thank you for voting!
The door light socket was broken and hanging down
6 of 9 people
found this instruction helpful.
-
David from Roanoke, VA
- Really Easy
- Less than 15 mins
The refrigerator light in our Kenmore fridge has been flaky for a number of years. The slightest bump would knock it out of the hole it fits into leaving the bulb dangling. Usually since we were used to it, we could avoid bumping it so it was no real problem, but a recent visitor bumped it and it once again was hanging. I decided this tim
... Read more
e, to take a serious look at it and fix the problem for real. I had options, duct tape, hot glue gun, goop...or a new part! A quick search on the internet, and I found www.PartSelect.com I entered my model # , quickly found the correct part number. The part came 1 1/2 days after I ordered it. The repair was very simple, I unplugged the fridge, removed the wires from the spade connectors on the old light socket, and attached them to the new socket. I then pushed the socket into the hole, and with new spring clips, it snapped snuggly into place. The socket came with extra wire connectors which I didn't need, the socket fits multiple brands of appliances. It also came with a bulb protector, but that wasn't needed for my fridge either. I was very pleased with the speed and ease of the repair. No more dangling light bulbs!
Read less
Was this helpful?
Thank you for voting!
Freezer would periodically allow things to partially thaw out
5 of 6 people
found this instruction helpful.
-
Dana from Canyon Lake, TX
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
First, I removed the two thermostat knobs, then the snap-on plastic cover. Then, I removed the 4 screws holding the housing for the timer, thermostats, etc., and dropped it down enough to remove the timer and the wiring harness going into it. Installing the new one was the same process, in reverse. Quite simple!
Was this helpful?
Thank you for voting!
Freezer was dripping water into refrigerator below
5 of 6 people
found this instruction helpful.
-
John from Redmond, WA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed the old timer from the housing. The replacement came with good instructions. I followed the instructions corresponding to the color wires in my unit. The first time it was installed, the fridge did not come on and the temperature rose after a couple hours. Looked at the part and realized the defrost cycle must have kicked in. Need
... Read more
ed to slightly turn the gray slotted part to initiate the timer so it would stop the defrost and start the fridge. That did it! It must have advanced the timer so it could accumulate run time. Whole repair saved us $3000 in a new fridge.
Read less
Was this helpful?
Thank you for voting!
Ice Maker Quit Making Ice
5 of 6 people
found this instruction helpful.
-
WILLIAM from Altamonte Springs, FL
- A Bit Difficult
- 15 - 30 mins
-
Nutdriver, Screw drivers, Wrench (Adjustable)
Ice make was still working but no water coming in to make ice . Pulled refrigerator back and found water valve at bottom of refrig close to the floor. I disconnected water line and electric plug - went to whirlpool web site - no help at all to confusing - found partselect and compaired picture of old valve with picture of new valve .
... Read more
When I got it in mail it took 30 min to install - working fine now hint - mark top of electric plug so you install correctly
Read less
Was this helpful?
Thank you for voting!
Removed the old parts then connected the new parts.
4 of 4 people
found this instruction helpful.
-
Jonathan from OLIVE BRANCH, MS
- Really Easy
- 30 - 60 mins
-
Screw drivers
The compressor immediately started when I plugged the refrigerator back in. Around 24 hours later the freezer compartment was at 0 degrees, and the refrigerator was at 35 degrees.
Was this helpful?
Thank you for voting!
water was leaking under the frig ,wasnt sure what the problem
4 of 4 people
found this instruction helpful.
-
stephen from ROCKLEDGE, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
decided to take a chance and replace the ice maker,so far no water leaking.feels nice to know the problem is fixed.thanks for the video on how to replace it, thanks again very easy repair
Was this helpful?
Thank you for voting!
Freezer making loud whining noise-Fridge not cooling well
7 of 13 people
found this instruction helpful.
-
Dale from Blaine, MN
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Removed the 3 screws in the back of the freezer, pulled back the metal back plate on the freezer. Removed 4 nuts on the plastic housing that holds the fan and pulled the housing down. Disconnected the wires, unscrewed the 2 screws holding the fan to the housing. Replaced old fan motor with new fan motor onto housing just as it was befo
... Read more
re. Reconnected the wires. And tested the motor. Worked great. Re-assembled everything as it was and it was done.
Read less
Was this helpful?
Thank you for voting!
frig stopped running and everything ruined
7 of 13 people
found this instruction helpful.
-
allen from Dickson, TN
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
The frig was already empty....removed the plastic control knobs and loosened the hex head screws to remove the cover . The wires were the same at each contact point, so, it took about 15 minuets to adjust the control knob to match the old one and reinstall the thermostat and place the cover...The other 15 minuets I spent finding my wife t
... Read more
o show her the frig was back to work...Just a walk in the park...
Read less
Was this helpful?
Thank you for voting!