1068699 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Movers broke the icemaker water fill tube shoving my refrigerator through the front door.
1 of 2 people
found this instruction helpful.
-
Christopher from Valley Village, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
I unscrewed the fill tube screws from the back of the fridge, and pulled the tube out.
Then I put the new tube in, screwed the screws back in and reconnected the waterline.
Then I put the new tube in, screwed the screws back in and reconnected the waterline.
Was this helpful?
Thank you for voting!
Old tube had cracked due to being frozen....
1 of 3 people
found this instruction helpful.
-
Stephen from Greensboro, NC
- Really Easy
- Less than 15 mins
-
Nutdriver
I followed the simple steps outlines in the great video! Thanks
Was this helpful?
Thank you for voting!
Refrigerator would not stay cold
2 of 6 people
found this instruction helpful.
-
Jeremy from State College, PA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench set
Removed rear cover to see non-operating fan - removed three mounting screws on the motor that were a challenge to access. Swapped fan from old motor onto new motor - one threaded nut on the motor shaft. Spliced new fan wires into fan wires of the wiring harness and mounted with three self-tapping screws supplied with new fan motor. Repl
... Read more
aced rear cover and plugged it in! Now the refrigerator cools like new (1981 model side-by-side Admiral)
Read less
Was this helpful?
Thank you for voting!
The door gasket was very hot which is caused by an overheated expansion line that runs along the area of the door gasket. This was caused by a failed cooling fan motor.
2 of 6 people
found this instruction helpful.
-
James from Howell, MI
- Easy
- 30 - 60 mins
-
Nutdriver
Pulled out the refrigerator and removed the two panels from the rear of the refrigerator. Removed the fan held in by four screws and unplugged the connector. Soldered on the original connector, installed the fan to the motor and re-installed the unit into the refrigerator. Then blew out and vaccumed the condenser coils.
Was this helpful?
Thank you for voting!
burned oven bulb
3 of 9 people
found this instruction helpful.
-
Ivanka from Atlantra, GA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh
... Read more
t bulb in was not the problem.
Read less
Was this helpful?
Thank you for voting!
Did not work light does not come on when the door opens. Would try the light socket. It not sure how good the switch got plugged in.
1 of 4 people
found this instruction helpful.
-
Cherilyn from CARROLLTON, TX
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
By watching a video.
Other Parts Used:
Was this helpful?
Thank you for voting!
Broken Kickplate Support Clip (Left side)
0 of 1 people
found this instruction helpful.
-
William from Fountain Valley, CA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
Unscrewed old broken part from the kickplate and attempted to install the new clip. Mounting screws would not go into the new clip. Had to drill out the mounting holes in the plastic clip using a #30 drill bit. Once the new clip was mounted, attempted to snap the kickplate back in place. Unfortunately at the left side the kickplate would
... Read more
not fully mate with the metal clip on the refrigerator body and would not snap all the way back to the refrigerator front surface, as the right side does. At least the kickplate doesn't fall down onto the floor on the left side as it did before. I suspect there is an alignment problem with the left side refrigerator metal clip, but have not pursued that yet.
Read less
Was this helpful?
Thank you for voting!
light staying on
0 of 1 people
found this instruction helpful.
-
Cecelia from Beaver Dam, WI
- Easy
- 15 - 30 mins
-
Screw drivers
A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.
Was this helpful?
Thank you for voting!
Filler Tube Broken At Elbow Where Line Hooks Up To
0 of 1 people
found this instruction helpful.
-
LARRY from PARKER, AZ
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Replaced fill tube
Was this helpful?
Thank you for voting!
Door Light switch cracked Mounting
0 of 1 people
found this instruction helpful.
-
Paul from Hinsdale, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights we
... Read more
re staying on (50 watts of heating). Replaced the switch and the frig started working like new.
Read less
Was this helpful?
Thank you for voting!
Broken light switch
0 of 1 people
found this instruction helpful.
-
George from North Scituate, RI
- Really Easy
- Less than 15 mins
-
Screw drivers
Part was easy to order, delivered quickly, installation very easy. Just unplug the unit, pop out the old swich using a screwdriver, disconnect and reconnect leads and pop switch back in. Definitely recommend that you can do it too.
Was this helpful?
Thank you for voting!
thread broke
0 of 1 people
found this instruction helpful.
-
uri from riverhead, NY
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
Unscrew broken piece, pull it out and then insert new one, security it in place and connect water line again, make sure It's thight check for leaks and done
Was this helpful?
Thank you for voting!
Water leaking onto the floor
0 of 1 people
found this instruction helpful.
-
Dean from Sheboygan, WI
- Really Easy
- 15 - 30 mins
-
Nutdriver
After finding water on the floor I investigated to find the leak. I Found theat the Icemaker fill tube on the back of the frig was cracked(due to someone pushing the frig back against the wall). Turned off the water supply to the icemaker. Removed the 2 screws holding the tube in place. Slid the tube out and slid the new one in. Replaced
... Read more
the screws and turned the water back on. Very easy, very inexpensive.
Read less
Was this helpful?
Thank you for voting!
After Hurricane Irene refrigeration compressore did not start
1 of 4 people
found this instruction helpful.
-
Bobby from New Bern, NC
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Followed the directions. Installation was quick. Took loner to put the covers back on and push the applicance back in position than the repair.
Was this helpful?
Thank you for voting!
Broken wheel under fridge
0 of 1 people
found this instruction helpful.
-
Ted from Magnolia, TX
- Really Easy
- 15 - 30 mins
-
Socket set
Replaced both since they came as a set. The only way it could have been any easier is if I had the wife do it. She had the remote this time. (•¿•)
Was this helpful?
Thank you for voting!