106866813 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
freezer (later fridge too) wouldn't stay cold~
2 of 3 people
found this instruction helpful.
-
David from MARYLAND HTS, MO
- Very Easy
- 30 - 60 mins
-
Nutdriver
****Make are you order Capacitor & Starter relay too (we ordered separtely so had to pay shipping twice)**** Super easy just open access panel on back near compressor and remove retention clip with fingers, remove & replace both capacitor & starter, put clip and acce
... Read more
ss panel back on, plug in and allow 8 hours to cool! Works like new again! Hope it goes another 10 years
Read less
Was this helpful?
Thank you for voting!
The refridgerator will not run
2 of 3 people
found this instruction helpful.
-
Victor from Colton, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
After the front panel was removed, disconnected the timer and installed new in reverse order. The provided instructions could be more straight forward, I spent more time reading it than the installation itself.
Was this helpful?
Thank you for voting!
replacing evaporator fan
2 of 3 people
found this instruction helpful.
-
Steve from SAN CARLOS, CA
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
My fridge did not have icemaker add on. The evap fan is in the freezer behind the back panel. Empty the freezer section (into a cooler) and turn the fridge off. Remove all the shelves in freezer section. Remove the shelf support tabs by lifting them up. use phillips head screwdiver to remove back panel in freezer section. Use nut driver t
... Read more
o remove fan shroud. Remove old fan and save the mounting arms. Install mounting arms on new fan and install fan. Install shroud, back panel, shelf mounts and shelves. Thats it!
Read less
Was this helpful?
Thank you for voting!
Refrigerator was freezing up and not cooling fresh food compartment
2 of 3 people
found this instruction helpful.
-
Greg from McLoud, OK
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
The repair was easy, I removed the cover on the top front of the fresh food compartment. It housed the defrost timer which was easy to identify and replace. Just removed a screw, unplugged the wires and replaced with the new part. Unfortunately, that wasn't the only problem. I also had to replace the defrost element that the timer sen
... Read more
t power to. While I was at it, I replaced the defroster thermostat. The entire repair took under an hour, diagnosing the problem took the most time and effort.
Read less
Was this helpful?
Thank you for voting!
Broke light switch while cleaning
2 of 3 people
found this instruction helpful.
-
Gail from Golden, CO
- Really Easy
- Less than 15 mins
use kitchen knife to pry out. replaced switch assemble and pressed back into place. Could not have done this with out help from previous customers. Thanks
Was this helpful?
Thank you for voting!
The plastic water fill tube got cracked when we moved. I called a parts company and they told me they couldn't just sell me the tube I would have to buy a whole kit for about $50 dollars. I decided to glue the tube. It worked for a while then it started leaking. So I thought I would have to buy
3 of 6 people
found this instruction helpful.
-
Joseph from Chesterfield, MO
- Really Easy
- Less than 15 mins
-
Screw drivers
I hand screwed the fill tube into the water tube and stuck it into the freezer hole. I screwed the fill tube to the back of the refrigerator.
Thanks so much! You saved me a bundle!!
Thanks so much! You saved me a bundle!!
Was this helpful?
Thank you for voting!
Light switch broke
2 of 4 people
found this instruction helpful.
-
Carolee from Spokane Valley, WA
- Really Easy
- Less than 15 mins
-
Screw drivers
Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.
Was this helpful?
Thank you for voting!
freezer quit working
1 person
found this instruction helpful.
-
Anthony from CIRCLEVILLE, OH
- Really Easy
- Less than 15 mins
-
Pliers
replaced relay switch
when I finally got started to do the repair it took 15 minutes my biggest delay was no instructions were sent with the part and it took time to get some
when I finally got started to do the repair it took 15 minutes my biggest delay was no instructions were sent with the part and it took time to get some
Was this helpful?
Thank you for voting!
Connection leaked as tube entered freezer
1 person
found this instruction helpful.
-
Robert from MERRIMACK, NH
- Very Easy
- 15 - 30 mins
Followed video and had one problen, the metal pipe would not release as shown,so I used a hacksaw between the plastic and metal pipe, removing the metal pipe from inside as the video shows. Good instructions.
Was this helpful?
Thank you for voting!
No cold
1 person
found this instruction helpful.
-
Jacqueline from LEXINGTON PK, MD
- Very Easy
- Less than 15 mins
-
Nutdriver, Pliers
Like you video
Was this helpful?
Thank you for voting!
Light rocker switch broke and refrigerator light couldn't go on.
2 of 4 people
found this instruction helpful.
-
Cathy from HOPATCONG, NJ
- Very Easy
- Less than 15 mins
I just popped out the old switch with a flat head screwdriver. Removed the connections and then installed new switch by reversing steps. Popped in back in and the light went on.
Was this helpful?
Thank you for voting!
The Light Socket Burned Out.
5 of 13 people
found this instruction helpful.
-
MATTHEW from STOCKTON, CA
- Really Easy
- Less than 15 mins
I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.
Was this helpful?
Thank you for voting!
Warm refrigerater
1 person
found this instruction helpful.
-
charles from REDDING, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Followed instructions from ideoo
Was this helpful?
Thank you for voting!
Freezer no longer frost free.
1 person
found this instruction helpful.
-
anthony from NORCROSS, GA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Reviewed Youtube video as a reference. Unplugged refrigerator. Removed old defrost timer. Matched the color of the wiring harness to the diagram that came with the part. Attach new part to wiring harness.
Was this helpful?
Thank you for voting!
compressor not running
1 person
found this instruction helpful.
-
Doug from Lancaster, CA
- Really Easy
- 15 - 30 mins
Removed the access panel on back of unit located the Run Capacitor on the compressor and removed the bad one and put the new one on and pugged refrigerator back in and it started up and works fine now
Was this helpful?
Thank you for voting!