1068656372 Kenmore Refrigerator - Instructions

All Instructions for the 1068656372
61 - 75 of 98

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
light would work intermitently
0 of 1 people found this instruction helpful.
  • Gregory from middle island, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.
Was this helpful?
Thank you for voting!
Internal light did not come on each time the door was opened.
0 of 1 people found this instruction helpful.
  • John from Jefferson Hills, PA
  • Really Easy
  • Less than 15 mins
After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.
Was this helpful?
Thank you for voting!
rocker switch broke off
0 of 1 people found this instruction helpful.
  • STANLEY from OAKLAND, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.
Was this helpful?
Thank you for voting!
light staying on
0 of 1 people found this instruction helpful.
  • Cecelia from Beaver Dam, WI
  • Easy
  • 15 - 30 mins
  • Screw drivers
A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.
Was this helpful?
Thank you for voting!
The light went out
0 of 2 people found this instruction helpful.
  • Janet from Flagstaff, AZ
  • Easy
  • Less than 15 mins
  • Screw drivers
I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.
Was this helpful?
Thank you for voting!
non-functioning refrigerator lite switch
0 of 2 people found this instruction helpful.
  • Ronald from Billings, MT
  • Really Easy
  • Less than 15 mins
  • Pliers, Wrench set
My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sin cerely, Ron Marshall, Billings, MT
Was this helpful?
Thank you for voting!
light switch would not work
0 of 2 people found this instruction helpful.
  • Joseph from Destin, FL
  • Really Easy
  • Less than 15 mins
Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!
Was this helpful?
Thank you for voting!
replace hinge bracket on fridge door
0 of 2 people found this instruction helpful.
  • Albert from Dunmore, PA
  • Easy
  • 15 - 30 mins
  • Socket set
taped the door shut ,measured a block of wood and stuck it under the door for support.....unbolted bottom hinge,slipped on hinge bracket and reassembled.no muss no fuss.
Was this helpful?
Thank you for voting!
Switch was not working after a repairman had fixed something else
0 of 4 people found this instruction helpful.
  • Jackie from Nova, OH
  • Really Easy
  • Less than 15 mins
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
Was this helpful?
Thank you for voting!
Switch didn't work
  • Don from Laramie, WY
  • Easy
  • 15 - 30 mins
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00
Was this helpful?
Thank you for voting!
Tray had rusted out, leaking!
  • Linda from Wilson, NC
  • Really Easy
  • 15 - 30 mins
  • Wrench set
Removed the screw from the old tray. Attached the new tray and return the screw using a wrench to assure the screw was torqued properly.
Was this helpful?
Thank you for voting!
Protective cover for bulb had melted
  • Lee from Brooklyn, NY
  • Very Difficult
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent i tems in the fridge from being able to touch. Bad solution.
Was this helpful?
Thank you for voting!
rReally Noisy Fan
  • Robert from Sierra Vista, AZ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
1. Unplug Refrigerator 2. Remove inside back freezer panel. (4 Screws) 3. Remove Duct Cover (3 Screws). 4. Cut electrical connections to fan. 5. Remove Old Fan motor (2 hex screws. 6. Install ground wire (was not one there previously). 7. Put slide-on electrical connectors on remaining 2 motor wires. (Were not any on original unit.) 8. R eplace Fan Motor (Don't forget the rubber vibration pads) 9. Reconnect electrical wires. 10. Press on plastic fan blade. 11. Plug in refrigerator to test install. It works. 12 Unplug refrigerator and replace ducting and back panel to freezer. Plug it back in. Voila, Quiet again.
Was this helpful?
Thank you for voting!
no problems at at all
  • Eliseo from Pleasanton, TX
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
removed rear wall panel took off old fan motor disconnected motor. Installed new grommets re-installed motor inserted new fan. Didn't have to trim fan re-connected wires and rear panel and reconnected power. no problems...
Was this helpful?
Thank you for voting!
Repalce evaporator fan
  • William from Ledyard, CT
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
The evaporator fan is located in the freezer behind the back wall. If you have the ice maker remove it first then remove the screws on the top of the panel. You will notice the side brackets for the top shelf will make it hard to remve the panal but by slitly binding the center the panal came right out. The fan is held in a bracke tha co mes right out. The wire unplu right from the fan so do not try to unplg the seal plug to the left side. Swap the fan with the new one useing the new rubber monts re-connect the wires and reasymble. Put the bottom of the back panal in first then work each side in past the shelf bracket binding the center slightly.
Was this helpful?
Thank you for voting!
All Instructions for the 1068656372
61 - 75 of 98