1068652 Kenmore Refrigerator - Instructions

All Instructions for the 1068652
76 - 90 of 376

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator light would not stay on
4 of 4 people found this instruction helpful.
  • Dave from Manchester Center, VT
  • Easy
  • 15 - 30 mins
  • Nutdriver, Socket set
Removed the 2 screws holding the light bulb shield, then the 4 uolding the metal panel. Unplugged the olw door switch and replaced.
reassembled the pieces.
Was this helpful?
Thank you for voting!
Freezer making loud whining noise-Fridge not cooling well
7 of 13 people found this instruction helpful.
  • Dale from Blaine, MN
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Removed the 3 screws in the back of the freezer, pulled back the metal back plate on the freezer. Removed 4 nuts on the plastic housing that holds the fan and pulled the housing down. Disconnected the wires, unscrewed the 2 screws holding the fan to the housing. Replaced old fan motor with new fan motor onto housing just as it was befo re. Reconnected the wires. And tested the motor. Worked great. Re-assembled everything as it was and it was done.
Was this helpful?
Thank you for voting!
frig stopped running and everything ruined
7 of 13 people found this instruction helpful.
  • allen from Dickson, TN
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
The frig was already empty....removed the plastic control knobs and loosened the hex head screws to remove the cover . The wires were the same at each contact point, so, it took about 15 minuets to adjust the control knob to match the old one and reinstall the thermostat and place the cover...The other 15 minuets I spent finding my wife t o show her the frig was back to work...Just a walk in the park...
Was this helpful?
Thank you for voting!
3 inches of frost in Fridge, 72 degrees in Fridgerator
6 of 10 people found this instruction helpful.
  • Gerald from Orangeburg, SC
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
First defrosted it to makes sure all Air flow was opened. Tested the Defroster heater with omh meter, it was OK. Found the location of the defrost timer on the online diagrams. Used nut driver to remove cover.
Replaced timer. The hardest part was decieding how to wire it up, tis was a universal kit and depending on how it was wired as to how often the defrost ran. The firt choice was every 8 hours. Since this was going to be opened often, I picked that one.
Plugged it with in 24 hrs freezer wall mesured -5 and the fridge was at 30, so had to warm it up a bit.
Now all complaints gone, Ice making has been doing better also.
Was this helpful?
Thank you for voting!
Lost shelf support bracket
4 of 4 people found this instruction helpful.
  • DAVID from LAFAYETTE, LA
  • Really Easy
  • Less than 15 mins
Ordered shelf support stud kit. Product was promptly delivered, and contained the parts as shown on website. Took longer to open the package than to replace the missing shelf support bracket. No problems. Would order from them again.
Was this helpful?
Thank you for voting!
would shut off and not restart without tapping on knob
4 of 4 people found this instruction helpful.
  • Brad from RAINIER, OR
  • Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
replaced the cold control thermostat . The new one was oriented 90 degrees off (on the bracket mount) so I had to turn it (in the bracket) to line up better with the wire connections and temp sensor tube. The power wires can be connected to either terminal however, and I suppose you could leave it as is if your wires can reach. Turning it will make the knob off 90 deg. off from original markings (off to coldest) but I simply remarked the position with a marker. (make sure you connect all terminals before mounting the bracket, it's much easier that way. .Note: this was a 40+ year old Sears "Coldspot" refridg. and it works like a dream since I changed out this original cold control. Love these old mechanical appliances that are much more reliable than the new brokered ones. Glad whirlpool has made many parts interchangeable through many years...kudos to them
Was this helpful?
Thank you for voting!
Freezer to warm
4 of 4 people found this instruction helpful.
  • Mike from DANSVILLE, NY
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Watched the videos and made it simple.
Was this helpful?
Thank you for voting!
Refrigerator light would not turn on.
5 of 8 people found this instruction helpful.
  • Suzanne from STERLING HTS, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom. The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.
Was this helpful?
Thank you for voting!
Refrigerator/Freezer not getting cold.
4 of 5 people found this instruction helpful.
  • Calvin from KELLER, TX
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Determined that compressor was not running, after researching problem on another site they recommended i try the condenser moor fan or motor, the defrost thermostat or defrost timer. . I was not satisfied with their recommendations. If I had tried their recommendations i would have likely gotten frustrated and spent upwards of $3000 to replace the 22 year-old hand me down unit. Thank you Parts Select for properly diagnosing my relay failure saving me a ton of money.
Was this helpful?
Thank you for voting!
Filler tube broken and old tube frozen over
4 of 5 people found this instruction helpful.
  • Alan from Chino, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Pliers, Screw drivers
this is a snap! 2 screws an a nut to tighten and it works like a charm. the filler tube in my Kenmore refer had broken off in the back. ( really bad location to put this in the beginning) if you push the refer to close to the wall you can break it off easily. remove the water line by loosing the nut and remove the hose from the fill tube ( This assumes you have already turned of the water supply or you are standing in a large puddle)remove the 2 screws that hold the filler tube in place. pull out the old filler tube in and slightly upright motion. replace the new fill tube into the same hole and replace the screws. replace the hose and tighten the nut, turn the water back on and check for leaks your done !!
doesn't that feel great?
Was this helpful?
Thank you for voting!
Broken filler tube at threaded connection
4 of 5 people found this instruction helpful.
  • Matthew from Phoenix, AZ
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
After discovering that the water noise was coming from the rear of the refridgerator upon pulling it foward I discivered the connection line had broken. So i got a phillips screw driver and removed the the two mounting screws and saw it was one piece. I easliy found the part on PartSelect website and once I got I merely swaped them out and it works good as new!
Was this helpful?
Thank you for voting!
Fan motor stopped working.
5 of 8 people found this instruction helpful.
  • John from Clifton Heights, PA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I first unplugged the unit.
Secondly I unscrewed the back panel and removed it.
Third, I unplugged the fan, unscrewed it, removed it, and replaced it with the new fan motor.
I then plugged it to confirm that it worked and then put everything back together.
Was this helpful?
Thank you for voting!
nosiy fan operation
4 of 5 people found this instruction helpful.
  • TOM from GRANVILLE, MA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
most of the time spent on repair was removing the food from freezer compartment other than that removal of a couple screws and disconnecting and reconnecting wires not a huge ordeal
Was this helpful?
Thank you for voting!
Broken Door Shelf Suport
4 of 5 people found this instruction helpful.
  • Charlie Jeanne from Lafayette, IN
  • Really Easy
  • Less than 15 mins
Our trusty fridge is so old that I couldn't find any replacement parts on the manufacturer's website. Thanks to PartSelect, I was able to keep narrowing down my request until I found an illustration of a part that matched my dimensions exactly. Delivery was FAST. Within 10 minutes I had the old duct-taped shelf support gone and a perfec t replacement part installed. Looks like new! I may be a 67-year old grandmother, but a pro couldn't have done it any faster or better. Thanks so much for your excellent website and prompt delivery!
Was this helpful?
Thank you for voting!
Freezer froze and refrigerator wet
5 of 8 people found this instruction helpful.
  • Patricia from Marengo, OH
  • Easy
  • 1- 2 hours
  • Screw drivers, Socket set
First took all frozen food out and than undid the screws that held back on--than cut the wires that held the piece and replaced it but also found that the plug was frozen so we thawed that out, that is why it took longer. Used air compressor to blow air and it broke it free and than we finished and put the food back after it got cold. So far it is working find and to beat all we received our part the next day so my husband could fix it that weekend--Thank you for the quick respond-
Patricia in Marengo Ohio
Was this helpful?
Thank you for voting!
All Instructions for the 1068652
76 - 90 of 376