1068650613 Kenmore Refrigerator - Instructions

Removed freezer shelving. Removed 3 shelving brackets (dovetailed) by sliding them up off of the small square mounted on the freezer wall. This was a stumbling block until
I figured out how to remove these brackets. Removed three Philips head screw in freezer back panel (24) with nut driver. Removed light bulb cover to get some grip on back panel. Lifted the back panel up slightly and then folded in down a bit then rotated it to the left. Removed 4 hex head (1/4in) screws on fan shroud (23) and brought down into the freezer. Disconnected electrical spade connectors from motor and removed entire unit from freezer to work on motor. Removed two hex head screws (18) holding motor to the brackets. Pushed new fan on to new motor using a 1/4 nut driver and hammer. Mounted motor to old brackets with two screws (18). Placed motor/fan/shroud unit in freezer and reconnected electrical spade connectors. Replaced motor/fan/shroud in freezer with the 4 hex head screws (15), dropping one behind the coils. Just replaced it with a look alike. Turned power back on to check if the fan was operating normally. Put back panel in place and screwed it in place then put shelving clips back into place and then all the shelving. Appears to operating quietly so far. About 30 minutes to complete the job.

Removed the 3 screws in the back of the freezer, pulled back the metal back plate on the freezer. Removed 4 nuts on the plastic housing that holds the fan and pulled the housing down. Disconnected the wires, unscrewed the 2 screws holding the fan to the housing. Replaced old fan motor with new fan motor onto housing just as it was before. Reconnected the wires. And tested the motor. Worked great. Re-assembled everything as it was and it was done.

most of the time spent on repair was removing the food from freezer compartment other than that removal of a couple screws and disconnecting and reconnecting wires not a huge ordeal

I first unplugged the unit.
Secondly I unscrewed the back panel and removed it.
Third, I unplugged the fan, unscrewed it, removed it, and replaced it with the new fan motor.
I then plugged it to confirm that it worked and then put everything back together.

Our trusty fridge is so old that I couldn't find any replacement parts on the manufacturer's website. Thanks to PartSelect, I was able to keep narrowing down my request until I found an illustration of a part that matched my dimensions exactly. Delivery was FAST. Within 10 minutes I had the old duct-taped shelf support gone and a perfect replacement part installed. Looks like new! I may be a 67-year old grandmother, but a pro couldn't have done it any faster or better. Thanks so much for your excellent website and prompt delivery!

First took all frozen food out and than undid the screws that held back on--than cut the wires that held the piece and replaced it but also found that the plug was frozen so we thawed that out, that is why it took longer. Used air compressor to blow air and it broke it free and than we finished and put the food back after it got cold. So far it is working find and to beat all we received our part the next day so my husband could fix it that weekend--Thank you for the quick respond-
Patricia in Marengo Ohio

Removed old switch and installed new - but did not solve problem

Took out old pieces and popped new ones in, just like that!

This Job is a brease - less than 5 minutes.

Be carelful not to bend metal shelf rail -
Remove broken end cap and slide out metal rail.
You can clean parts before reinstalling.
I recommend slightly squeezing rail before reinstalling to tighten the contact points with plastic end caps.
slide metal rail into end caps (they should snap if contact is right) and secure with sticky tape (sticky tape is supplied with pair of end caps).
Reinstall rail with endcaps attached.
I even have one extra end cap left for another repair if neccessary!

I removed all the shelves and the back shelf hanger. Removed two screws on the back plate.Pulled it out.Removed the screws that hold the fan housing. Pulled it out so I could write down the three wires color and location.Unpluged them.Removed the old fan and installed the new one.and put everthing back together.

Removed the shelves from the freezer and the brackets holding it along with the covers for the light and plate for the ice maker (we don't have one). Pulled the ground wire from the tab off the port for the ice maker. Removed back plate exposing the fan motor and then the 4 hex screws holding on part #23 of the diagram which the fan motor is mounted to. Flipped it over, unscrewed the 2 hex screws from the fan motor mounting and removed it. Removed and replaced 3 wire connectors on new fan motor. Installed new fan motor and new grommets but used the old screws because the provided screws were larger. Pushed the new fan on to the motor shaft. Reassembled. Half hour most.

Remove bottom of freezer by sliding out the gaskets on each side.

Remove back of freezer. 6 screws.

Remove fan cover. 4 screws.

Remove fan. 3 wires to disconnect. 2 screws to take out.

Install the fan. Connect the 3 wires. Fastened with 2 screws.
Put fan cover back on. 4 screws.
Put back of freezer back on. 6 screws.
Put bottom of freezer back in. Slide gaskets in on each side.

I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.

Order the part from the Internet on Sunday, it mailed out on Monday and I received it on Tuesday. I unplugged the fan then undone 3 screws that held the fan bracket to the refrigerator pulled it out unscrewed 3 more nuts and replaced the fan on the bracket and I cut the old wire plug off the old fan and with 2 wire nuts put it on my new fan. Replaced the fan and bracket back on the refrigerator plugged it in and it works like a new refrigerator.

removed back cover, removed fan motor and replaced with new one. connected new power wires. worked right away