All Installation Instructions for Kenmore Refrigerator 1068650511

Mounting bracket was riveted on old motor, mounting bracket holes on new motor were different

removed shims on screws holding motor together, enlarged hole in mounting bracket so motor screws could also go through mounting brackets.

Parts Used:

Evaporator Fan Motor Kit

MIKE from ARLINGTON, OR
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

original motor stopped

removed old and instaslled new. biggest problem was getting to one of the screws.

Parts Used:

Refrigerator Condenser Fan Motor Kit

Paul from Lowell, MI
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Socket set

2 of 4 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Condenser Fan Failure

Partition between Freezer and Fridge was running very hot. (Warm is normal). Oiling fan did not work. The only problems encountered in the replacement were getting fan out and in through coolant lines, cut plug off to accomodate generic fan wiring, getting the screws back in without cooking your hand on a hot compressor. Unit works great!

Parts Used:

Refrigerator Condenser Fan Motor Kit

Al from Tonka Bay, MN
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set

2 of 5 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

freezer and food section too warm

removed lower back cover. diconnected fan ass'y electrical connection, removed fan housing (3 screws). removed fan motor from housing. cut old connector from fan and installed on new fan with wire nuts included. re-installed new fan to housing and re-installed housing to frame.

Parts Used:

Refrigerator Condenser Fan Motor Kit

William from Milford, MA
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Socket set

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Nonr

Replaced missing stud.

Parts Used:

Shelf Stud

Gaynell P from Spring, TX
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Motor noise while running and clicking when shutting off

The instruction sheet supplied with the new motor described the steps to take very good. Replaced the rubber grommets for the three motor mounts also. A flashlight or light source was needed or was very helpful.

Parts Used:

Refrigerator Condenser Fan Motor Kit

Curtis from Sedona, AZ
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

refrigerator stopped cooling due to condenser over-heating

Pull refrigerator out to access back, unplug unit and remove the 3 .25" screws cut the power leads to motor and install new with easy to understand instructions provided with new motor. Plug refrigerator back in and enjoy your cold beverages once more. EASIEST REPAIR EVER.

Parts Used:

Refrigerator Condenser Fan Motor Kit

Kevin from COVINGTON, LA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Two of the parts were broken so the shelf was laying on the drawers so neither could be used effectivly

Pulled out the stud with a wire cutter and replaced it with the exact part you shipped in the kit.

The other 2 parts just slipped on the brackets

Nice thing is now I have extra parts for the other shelf.

Parts Used:

Shelf Stud

ROD from LINCOLN, NE
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Movers broke the icemaker water fill tube shoving my refrigerator through the front door.

I unscrewed the fill tube screws from the back of the fridge, and pulled the tube out.

Then I put the new tube in, screwed the screws back in and reconnected the waterline.

Parts Used:

Ice Maker Water Fill Tube Kit

Christopher from Valley Village, CA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken shelf supports

Took just a few moments to install. The parts fit like a glove,

Parts Used:

Shelf Stud

Bob from Las Vegas, NV
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Poor design leaves fitting vulnerable to damage. Part was broken when pushed to close to the wall.

Simply removed the old and replaced with the new part.

Parts Used:

Ice Maker Water Fill Tube Kit

Mike from Camas, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

One of the door shelf end caps broke

I removed the broken end cap and then I snapped the metal shelf onto both end caps and replaced the shelf.

I really must say that dealing with PartSelect was exceptional. It took about three days for me to get the part and, prior to that, it was very easy for this sidewalk fixer to locate the correct part on their website. Thank you for your excellent service.

Parts Used:

Refrigerator Door Shelf End Cap

Gary from Aberdeen, SD
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Broken End cap on fridge shelf

Removed the existing broken end cap, and replaced it with the new one. Installed shelf securely back in fridge. Easiest repair I've ever done. Less than 5 minutes. I wish everything were that easy.

Parts Used:

Refrigerator Door Shelf End Cap

Nathan from Coralville, IA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

1 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Both front wheels were severly damaged needing replacement.

I tipped the refrigerator back and my friend used an adjustable wrench to attach put the new wheel assembies on. I also used a socket wrench to get the old attacheement bolts to thread. I rolled the cleaned appliance in place and adjusted the wheels with the socket set for easy door closing. It went smoothly.

Parts Used: