- Home
- 1068648321
- Instructions
1068648321 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
light would come on and off
-
Dora from Rock Island, IL
- Really Easy
- Less than 15 mins
Viewed the viedo - it showed what to do
Was this helpful?
Thank you for voting!
No Light
-
Mary from Jefferson Township, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.
Was this helpful?
Thank you for voting!
exchange of defective light rocker switch
-
Steve from River Edge, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch
Was this helpful?
Thank you for voting!
Light in the refrigerator didn't work
-
Anthony from Fairport, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.
Was this helpful?
Thank you for voting!
Evaporator fan motor stopped working
-
Kurt from Baltimore, MD
- Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers, Wrench set
Remove back cover of freezer compartment; Remove old fan assembly, new fan terminals did not exactly match old one so I had to remove one of the terminals from old fan and attach it to new fan/ then install new assembly and repaced freezer cover
Was this helpful?
Thank you for voting!
Evaporator motor squeal.
-
Steven from Hilliard, OH
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
After finding an almost obsolete part( thanks PartSelect!) the installation was rather easy. Remove the back panel of the freezer and vent with a screwdriver and a nut driver. Disconnect the three wires, green, white and red.Remove motor from mounting and replace with new motor. I had to make a slight adjustment to the ground wire on the
... Read more
new motor that required adjusting the position of the contact-no big deal. The motor fit perfectly. Popped fan on and assembled. 20 minutes max.
Read less
Was this helpful?
Thank you for voting!
The fan in the freezer was squealing
-
Maxine from Henderson, NV
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Took the old fan out and put the new fan in.
Was this helpful?
Thank you for voting!
noisey circulating fan in the freezer
-
Lee from Arvada, CO
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Emptied the freezer. Removed the back panel. (six screws)Removed the fan cover.(4 screws) Unplugged the power. Unplugged three wires from the motor. (hot-neutral-ground)Removed the fan. (2 screws) Installed the new fan and centered for clearance. Reversed the prior instructions.
Was this helpful?
Thank you for voting!
Both light bulbs had been replaced, but lights did not turn on.
-
Richard from Arlington, MA
- A Bit Difficult
- 30 - 60 mins
-
Pliers, Screw drivers
I tried to remove the old light switch using a putty knife and a hammer. It was hard to compress the plastic tabs to pull it back through the hole, but all of a sudden, the lights came on. I guess banging on the switch freed-up the contacts. The new switch is now a spare part in case I need it.
Was this helpful?
Thank you for voting!