- Home
- 1068644321
- Instructions
1068644321 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
fresh food side not getting cold
-
Garry from Sayville, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver
I wasnt about to call Mr Appliance of Bayport NY the last time I called him I got a bill for $72.00 and he told me I needed a new frig. So I paid him then the next day I went to parts select and fixed it myself for about $50.00 But this time it was my Moms frig and the frig side (fresh food side) wasnt getting cold So again I went to part
... Read more
s select and put in a bimetel thermostat and it works perfect now. Im sure I saved a lot of $ and thanks to parts select, They helped me diagnose the problem and make the repair step by step! EASY! Thanks parts select...Garry from long island NY
Read less
Was this helpful?
Thank you for voting!
Repalce evaporator fan
-
William from Ledyard, CT
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
The evaporator fan is located in the freezer behind the back wall. If you have the ice maker remove it first then remove the screws on the top of the panel. You will notice the side brackets for the top shelf will make it hard to remve the panal but by slitly binding the center the panal came right out. The fan is held in a bracke tha co
... Read more
mes right out. The wire unplu right from the fan so do not try to unplg the seal plug to the left side. Swap the fan with the new one useing the new rubber monts re-connect the wires and reasymble. Put the bottom of the back panal in first then work each side in past the shelf bracket binding the center slightly.
Read less
Was this helpful?
Thank you for voting!
no problems at at all
-
Eliseo from Pleasanton, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
removed rear wall panel took off old fan motor disconnected motor. Installed new grommets re-installed motor inserted new fan. Didn't have to trim fan re-connected wires and rear panel and reconnected power. no problems...
Was this helpful?
Thank you for voting!
Replace door gasket
-
Susan from Pearland, TX
- Really Easy
- 15 - 30 mins
-
Nutdriver
Needed to replace a really old Refrigerator Door Gasket and was having difficulty locating a door gasket for this unit. We didn't even know the age of the unit, but found the model number of the refrigerator which no one really lists on websites because it's so old. Customer service found the Model we had, we ordered and it was received
... Read more
at our home the next day.Price was good and the shipping chg was very reasonable. Very pleased and will definately order from them again! Thanks!!!!
Read less
Was this helpful?
Thank you for voting!
Broke the arm off the food compartment rocker switch
-
David from St. Pete Beach, FL
- A Bit Difficult
- 15 - 30 mins
-
Pliers, Screw drivers
After receiving the new part almost immediately,using two screw drivers, removed the broken switch from the plastic frame. Be careful not to scratch or otherwise tear the plastic...very pliable. Since the original switch was factory installed and the wires were packed in fiberglass insulation, the switch came out but the wires and clips
... Read more
were still in place and could not reach the new switch. It was necessary to pull them down with bent long nose pliers...used a lot of "pull" but the wires held up.Connected the switch, turned the power on and there was light! Reports from other users really took the uncertainty out of the task.
Read less
Was this helpful?
Thank you for voting!
The fan in the freezer was squealing
-
Maxine from Henderson, NV
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
Took the old fan out and put the new fan in.
Was this helpful?
Thank you for voting!
Evaporator fan motor stopped working
-
Kurt from Baltimore, MD
- Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers, Wrench set
Remove back cover of freezer compartment; Remove old fan assembly, new fan terminals did not exactly match old one so I had to remove one of the terminals from old fan and attach it to new fan/ then install new assembly and repaced freezer cover
Was this helpful?
Thank you for voting!