- Home
- 1068618213
- Instructions
1068618213 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Water fill tube broken
3 of 4 people
found this instruction helpful.
-
Jeffrey from Monroe, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
removed two screws and pulled part out of the unit. The local appliance store said they needed model and part # to try to identify and order the part. Found part select online, found the part immediately, ordered the part for $4.50 or so. Part was delivered in 2 days! Very easy installation and the part works perfectly. Thanks so muc
... Read more
h!
Read less
Was this helpful?
Thank you for voting!
defective light switch
3 of 4 people
found this instruction helpful.
-
THOMAS from WILLARD, OH
- Really Easy
- Less than 15 mins
inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.
Was this helpful?
Thank you for voting!
The water fill tube 90 fitting broke
3 of 4 people
found this instruction helpful.
-
Scott from Crete, IL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Removed brokent tube fitting from the compression nut.
Removed two screws holding the fill tube. Removed and replaced the fill tube. Direct replacement, no cutting tube length. Reconnect water line to the new fill tube.......Done.
Removed two screws holding the fill tube. Removed and replaced the fill tube. Direct replacement, no cutting tube length. Reconnect water line to the new fill tube.......Done.
Was this helpful?
Thank you for voting!
Divider front of fridge hot to touch Condenser fan not working
3 of 4 people
found this instruction helpful.
-
John from Holden, MA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
removed back cover, removed fan motor and replaced with new one. connected new power wires. worked right away
Was this helpful?
Thank you for voting!
the light socket broke apart
4 of 7 people
found this instruction helpful.
-
Elyse from Skokie, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers
I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.
Was this helpful?
Thank you for voting!
changed the light bulb still would not work so I figured it was the switch sure enough.
3 of 4 people
found this instruction helpful.
-
anthony from HAVELOCK, NC
- Really Easy
- 15 - 30 mins
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this helpful?
Thank you for voting!
Faulty light socket
3 of 5 people
found this instruction helpful.
-
Larry from HOUSTON, TX
- Very Easy
- 15 - 30 mins
-
Screw drivers
Followed the video instructions.
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people
found this instruction helpful.
-
Yafa (and David) from Bothell, WA
- Easy
- Less than 15 mins
-
Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
Door light switch disintegrated
2 of 2 people
found this instruction helpful.
-
Thomas from Roseville, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
Very simple fix, remove 3 screws, two connectors to the old switch
Was this helpful?
Thank you for voting!
fridge door switch did not work
2 of 2 people
found this instruction helpful.
-
stu from richmond, VA
- Easy
- Less than 15 mins
-
Socket set
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this helpful?
Thank you for voting!
Light didnt go on
3 of 5 people
found this instruction helpful.
-
dorotea from staten island, NY
- Really Easy
- Less than 15 mins
-
Screw drivers
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this helpful?
Thank you for voting!
Bad fan motor
3 of 5 people
found this instruction helpful.
-
Mark from Farmington Hills, MI
- Easy
- 15 - 30 mins
-
Nutdriver
Pop off six mounting screws and the ground screw. Remove the fan blade and reattach. Reinstall. Save yourself big bucks.
Was this helpful?
Thank you for voting!
fans and lights worked in refrigerator but not cooling
9 of 23 people
found this instruction helpful.
-
James from Blue Springs, MO
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
By going on line and going to PartsSelect, the check out procedures traced the problem to the start/overload relay. Using a nut driver, I removed the back panel and using their instruction, I installed the overload relay. On the next to the last step on the instruction, the sealer in the kit was already hardened. I called the service
... Read more
hot line at PartsSelect and they apologized and sent me another kit to finish the repair. In two days, the new kit came and the repair was complete. The whole experience with PartsSelect was great.
Read less
Was this helpful?
Thank you for voting!
Fan was noisy - bearing had failed
2 of 2 people
found this instruction helpful.
-
Karl from Wellesley, MA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.
Was this helpful?
Thank you for voting!
Broken plastic part at top of water fill tube to freezer
2 of 2 people
found this instruction helpful.
-
Jay from Mt. Pleasant, WI
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
Simple. 1st, removed broken part to understand part (water fill tube to freezer, plastic part at top of fill tube cracked). 2nd go on your web site and look at prints to find part number, Study video to understand video. 3rd. Called customer service and lady was very nice and efficient. Placed order and received. Study video again a
... Read more
nd installed. My 9 year old grandson was visiting from out of town and assisted in installation. Just over 30 minutes to install
Read less
Was this helpful?
Thank you for voting!