1068539680 Kenmore Refrigerator - Instructions

All Instructions for the 1068539680
91 - 105 of 561

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
door closing cam was broken
3 of 3 people found this instruction helpful.
  • lizie from nantucket, MA
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Screw drivers
the process was pretty straight forward though the part came without instructions. We were able to replace the part improperly with ease. however, we were not able to get the pieces aligned properly for a long time. We ended up taking the door off many times to try to realign the pieces. After many hours I finally unscrewed the bottom cam while the door was in place. The piece popped into place and all was fixed. Had the part come with directions telling us to do this we would have replaced the cam within 15 minutes!
Was this helpful?
Thank you for voting!
Icemaker motor quit
3 of 3 people found this instruction helpful.
  • David from Selma, IN
  • Easy
  • 15 - 30 mins
  • Nutdriver
This was a snap. Loosened 3 screws, removed
old ice maker. Made cutout for water chute. Plugged in
wiring harness plug. Installed new ice maker. Tightened 3 screws.

These brain surgeons that charge $80.00 just to show up at my house to repair an appliance are history.
Was this helpful?
Thank you for voting!
lights wouldn't come on/work in refrigerator
4 of 6 people found this instruction helpful.
  • Jane from Albuquerque, NM
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Socket set
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80.. .would have been at least $100 to have a repair person come to the house!
Was this helpful?
Thank you for voting!
Compressor making excessive noise
5 of 9 people found this instruction helpful.
  • chester from Tampa, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
One front roller was flat on one side. Decided to replace all rollers at same time. Placed shims under unit and removed mounting screws for one front and one rear roller. With new rollers in place, I was able to level the refrigerator side to side, but unable to do so, front to back. Left the new front roller in place and reinstalled the old rear roller. Have decided to replace refrigeratorin the near future. This is one of my few repair failures!
Was this helpful?
Thank you for voting!
water dripping in ice cube holder
4 of 6 people found this instruction helpful.
  • Christine from Clarkston, MI
  • Really Easy
  • 15 - 30 mins
  • Screw drivers
We removed three screws, unplugged the wire and then removed the old ice maker. Installed the new ice maker with the screws, plugged in the wire and shortly after that we had ice! I was nervous about this repair but it was so easy and the part was here in three days.
Was this helpful?
Thank you for voting!
Broken Freezer Door Cams
3 of 3 people found this instruction helpful.
  • Dennis from Corona, CA
  • Easy
  • 30 - 60 mins
  • Socket set
1. Put pieces of wood under door to support it.
2. Unscrew three screws holding door hinge.
3. Disconnect water line.
4. Unscrew screw holding each cam. One to door and one to hinge.
5 Replace cams.
6. Retrieve plate with threaded holes behind frame that the hinge attaches to.
7. Use thin philips screwdriver through the hinge bracket, shim, frame and screw plate to align it for the other two screws.
8. Replace all three hinge screws.
9. Connect water line fitting.
10. Remove wood for door support.
11. Check door for smooth movement and strong pressure when closed.
Was this helpful?
Thank you for voting!
Would not make ice any longer
4 of 6 people found this instruction helpful.
  • James from Concord, MA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
I determined that the ice cube maker was no longer heating the cubes so they could be released into the ice tray. After ordering a new unit, taking out four screws and disconnecting the quick disconnect of wires I plugged the new one in and we were back in business.
Was this helpful?
Thank you for voting!
Raplaced switch
5 of 9 people found this instruction helpful.
  • Winston A from Brooklyn, NY
  • Really Easy
  • Less than 15 mins
  • Pliers
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Was this helpful?
Thank you for voting!
badly worn cam
3 of 3 people found this instruction helpful.
  • harry from KINGSPORT, TN
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Exactly as the demo instructed. It was very detail friendly and was very easy to follow.
Was this helpful?
Thank you for voting!
changed the light bulb still would not work so I figured it was the switch sure enough.
3 of 4 people found this instruction helpful.
  • anthony from HAVELOCK, NC
  • Really Easy
  • 15 - 30 mins
I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.
Was this helpful?
Thank you for voting!
heating element going bad
4 of 7 people found this instruction helpful.
  • James from Bakersfield, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
I removed three sheet metal screws, unsnapped the electrical pigtail. Then snapped out knock out on new maker. Matched the electrical connection, pushed it in place. Finally set new one in place, leveled it, tightened the scews and walked away.
Was this helpful?
Thank you for voting!
replaced non-functional ice maker
3 of 4 people found this instruction helpful.
  • Richard from Troy, MI
  • Easy
  • Less than 15 mins
  • Nutdriver
After first unplugging the refrigerator from it's electrical power source,I removed the lower screw of the ice making unit with a nut driver. I then loosened the upper two screws which hold the retainer clips that secure the unit tight to the freezer wall. I then lifted the unit upward and outward a few inches to allow access to the wire harness. I unplugged the haness from rear of the freezer and removed the unit completely.
To install just reverse the procedure.
Was this helpful?
Thank you for voting!
Ice maker needed to be replaced as it quit working.
3 of 4 people found this instruction helpful.
  • Ronald from Henderson, NV
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Loosened two top screws using a hand held mirror and screwdriver and removed a bottom screw then unplugged the unit inside. Five minutes and repair was complete. Easy as that!
Was this helpful?
Thank you for voting!
Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...
3 of 4 people found this instruction helpful.
  • David from Hemet, CA
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull t he connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!
Was this helpful?
Thank you for voting!
ice tray leaking
9 of 22 people found this instruction helpful.
  • Linda from Santa Maria, CA
  • Really Easy
  • Less than 15 mins
Super! It was so fast and easy to fix. Receive my kit in three days and save a lot of money not having to have a repairman come and do it!
Was this helpful?
Thank you for voting!
All Instructions for the 1068539680
91 - 105 of 561