- Home
- 1068539660
- Instructions
1068539660 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Original ice maker quit making ice, leaked water.
2 of 2 people
found this instruction helpful.
-
John from Yorba Linda, CA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
Removed the old ice maker (2 screws, about 2 minutes). Read the excellent instructions. Prepped the replacement unit by adding the mount bracket. It plugged straight into the existing fridge wiring harness. Amazing how standardized icemakers are! Total time for a very careful job was under an hour.
It came in the mail, I got ... Read more home about 5pm and had it installed that evening before dinner. First load of ice was in the catcher before I went to bed.
Very nice kit, and economical compared to a new fridge!
It came in the mail, I got ... Read more home about 5pm and had it installed that evening before dinner. First load of ice was in the catcher before I went to bed.
Very nice kit, and economical compared to a new fridge!
Read less
Was this helpful?
Thank you for voting!
Ice Maker Not Creating Ice Cubes
2 of 2 people
found this instruction helpful.
-
Daniel from Albuquerque, NM
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
Removed Ice tray and flap followed by the three screws that held the old ice maker in place. (I probably didn't have to remove the top two, they are designed to just loosen and lift up on the mecanism to free.) I then pulled the old wiring harness out of the original ice maker. A small screw driver helped in depressing a tab while pulling
... Read more
on the harness. The same process was used to remove the wiring harness that was attached to the new replacement unit. I connected the original wiring harness that I had disconnected from the bad ice maker, and it fit perfectly into the replacement unit. No need to splice or use any of the harnesses that came with replacement. I tried installing the new unit and discovered that there was interfernce with the water feed hose. I had forgotten to break off the tab on the end of the replacement unit. Once I did that using pliers, the unit fit fine. I tightened the screws, installed the on/off mecanism and replaced the tray and flap. I then waited and waited, hoping to hear the forgotten sound of water entering the ice maker. Had a beer and walked the dogs thinking I had failed, but low and behold, over an hour later, the ice maker turned on the water. Many hours later, my wife woke me up in the middle of the night to declare we had cubes! Success.
Read less
Was this helpful?
Thank you for voting!
fans and lights worked in refrigerator but not cooling
9 of 23 people
found this instruction helpful.
-
James from Blue Springs, MO
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
By going on line and going to PartsSelect, the check out procedures traced the problem to the start/overload relay. Using a nut driver, I removed the back panel and using their instruction, I installed the overload relay. On the next to the last step on the instruction, the sealer in the kit was already hardened. I called the service
... Read more
hot line at PartsSelect and they apologized and sent me another kit to finish the repair. In two days, the new kit came and the repair was complete. The whole experience with PartsSelect was great.
Read less
Was this helpful?
Thank you for voting!
door would not stay shut on refrigerator side
2 of 2 people
found this instruction helpful.
-
tom from BASSETT, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Socket set
Remove one 5/16 screw from top hinge cover plate. Trace outline of hinge on top of refrigerator with sharpie, so you will know where to put hinge back. Remove 3 5/16 screws from hinge. Lift door up out of bottom hinge, place on table to be able to work on. Remove one 5/16 screw and upper cam piece from bottom of door and replace with new
... Read more
upper cam piece. Remove one 5/16 screw and lower cam piece from bottom hinge on refrigerator. Replace with new lower cam piece and one screw Set door back in place and reattach top hinge with 3 screws adjust refrigerator door as needed for a nice even gap between freezer and refrigerator doors. Tighten screws down and put hinge cover back on with one screw.
Read less
Was this helpful?
Thank you for voting!
Lower hinge on freezer door on side-by-side broke
2 of 2 people
found this instruction helpful.
-
Paul from Amherst, MA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
Removed the cover plate on top. Used a wrench and the nut driver to remove the three screws & the screw holding the grounding wire. Pulled apart the plastic coupling for the wiring to light the freezer. Then with the aid of a friend - lifted the door (with food removed from door shelves) off the hinge. This freezer had a water line wh
... Read more
ich we didin't know how to disconnect so we were careful to move the door slightly away from the broken hinge, set it on a stool with one person holding the door steady while the other person installed the new hinge piece. Definitely takes two people (as suggested in the directions) to both lift and guide the door into place. Once it was in place - I reinserted the screws up top and tightened them. Then had to untighten them to get the door to line up as it should vertically - so I would suggest just lighten tighen the upper screws until the door is aligned and swinging smoothly. Then reattached ground wire and plastic coupling. Works great.
Read less
Was this helpful?
Thank you for voting!
Door Closing Cam Kit Failed
2 of 2 people
found this instruction helpful.
-
Digger from Marysville, WA
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed all of the food from the door by lifting the shelves out. Unbolted the top door hinge, and lifted the door off. Replaced the cam and placed the door back on, re-bolted the top hinge and placed all of the food and shelving back into the door. The door closes and seals when it is shut.
Was this helpful?
Thank you for voting!
Fan was noisy - bearing had failed
2 of 2 people
found this instruction helpful.
-
Karl from Wellesley, MA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.
Was this helpful?
Thank you for voting!
Machine Leaking Water
2 of 2 people
found this instruction helpful.
-
Frank from BERKELEY HTS, NJ
- Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
I did some tests and determined that the tub-to-pump drain hose had a leak in it.I then looked on the web to find disassembly instructions. I have a stacked washer dryer combination in a very confined space. The repair involved disconnecting both the washer and dryer from the water, gas, electric and venting systems first, then unstacking
... Read more
the dryer from the washer (not so easy, it required a helper). The machine was then pulled out so I could get at the parts necessary to remove the outside components and sheet metal. Then, I disassembled the top, front and access panel in the back. The disassembly went very well. I got access to the drain hose assembly and removed it fairly easily. I ordered a replacement drain hose assembly and found that installing the large port of the assembly was very difficult. (The two other ports were easy.) After thinking about it, I tilted the machine back a bit so I could try it from the bottom. That worked fine.I then reassembled and tested the machine. No leaks. Good luck with yours!
Read less
Was this helpful?
Thank you for voting!
Ice Maker started acting up
2 of 2 people
found this instruction helpful.
-
Bill from Sumas, WA
- Easy
- 15 - 30 mins
-
Nutdriver
I removed the 2 screws on top and the one screw underneath holding the Ice Maker to the wall of freezer.I pulled the electrical connection from the wall next (wiggled it back and forth until it came out).
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts ... Read more to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts ... Read more to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks
Read less
Was this helpful?
Thank you for voting!
Bad fan motor
3 of 5 people
found this instruction helpful.
-
Mark from Farmington Hills, MI
- Easy
- 15 - 30 mins
-
Nutdriver
Pop off six mounting screws and the ground screw. Remove the fan blade and reattach. Reinstall. Save yourself big bucks.
Was this helpful?
Thank you for voting!
Stopped making ice. Black stuff coming out on ice
2 of 2 people
found this instruction helpful.
-
Paul from Navarre, FL
- Easy
- Less than 15 mins
-
Nutdriver
First I removed the (3) screws holding the unit to the side of freezer wall with a nutdriver. Then I disconnect the Harness from the back of the freezer. You have to work the Harness off connector because it was very tight. The Unit came with the correct harness installed so I reconnected the harness to the Freezer and replaced the (3) sc
... Read more
rews. I had ice in about 2.5 hours.
Read less
Was this helpful?
Thank you for voting!
Ice maker quit, I cross wired the two solenoid valves and determined the valvles were not the problem.
2 of 2 people
found this instruction helpful.
-
michael from naples, FL
- Easy
- Less than 15 mins
-
Nutdriver
Used a nutdriver and removed the lower mount nut, then loosened the the top two nuts and the icemaker lifted off, then unplugged the device and replugged it into the "old" plug(the new ones were not needed) then remounted it. Then it did not fill (as others posted happened right away.) Some poster suggested manually filling the tray so I
... Read more
did it. Later it froze and emptied and refilled and started working normally. Not sure if putting water had anything to do with it or it just took some time. It would be nice if the instructions addressed this issue.
Read less
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people
found this instruction helpful.
-
Yafa (and David) from Bothell, WA
- Easy
- Less than 15 mins
-
Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.
Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
fridge door switch did not work
2 of 2 people
found this instruction helpful.
-
stu from richmond, VA
- Easy
- Less than 15 mins
-
Socket set
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!
Why didn't I order this part and do the repair earlier? Very simple.
Why didn't I order this part and do the repair earlier? Very simple.
Was this helpful?
Thank you for voting!
Ice maker went bad
3 of 5 people
found this instruction helpful.
-
DENNIS from SOUTH LYON, MI
- Really Easy
- Less than 15 mins
-
Nutdriver
Took the old one out in Two Min's, Replaced with the new one in about the same time.
Had ice within 1 hour
Had ice within 1 hour
Was this helpful?
Thank you for voting!