- Home
- 1068539622
- Instructions
1068539622 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Divider front of fridge hot to touch Condenser fan not working
3 of 4 people
found this instruction helpful.
-
John from Holden, MA
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
removed back cover, removed fan motor and replaced with new one. connected new power wires. worked right away
Was this helpful?
Thank you for voting!
Ice maker was not working.
4 of 7 people
found this instruction helpful.
-
Doyle from Winchester, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
On my particular model refrigerator I only needed to remove one screw and disconnet the plug. I then slid the unit out. The new ice maker did not come with the plastic sled that was attached to the old unit. I removed and attached the sled to the new unit with 3 screws.
Was this helpful?
Thank you for voting!
Ice maker wouldn't work
3 of 4 people
found this instruction helpful.
-
Rich from Covina, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Ice maker wouldn't eject the ice often enough. After reading a few other stories, I just ordered the universal ice maker from Part Select. All I had to do was remove some of the plastic shrouds from my old ice maker and put them on the new one. I also reused my mounting brackets. The whole job took me 20 minutes.
Was this helpful?
Thank you for voting!
Icemaker Died
3 of 4 people
found this instruction helpful.
-
Don from Jacksonville, TX
- Easy
- 15 - 30 mins
-
Socket set
The instructions are practically no help, but if you study the diagram, you can figure out the one screw you need to remove. Then the icemaker lift off of two brackets. I couldn't see how to use a screwdriver to unlock the bracket, but just applying mild pressure and pulling it forward brought it right out. I didn't have to change anyt
... Read more
hing with the plug already intalled so it was very easy to pop in, lock the plug, pop into brackets, replace screw and I was in business. 24 hours later I had a bucket of ice! 15 minutes to figure out how to get old out and 5 min to replace new one. Fairly easy. Read posts here to get hints!
Read less
Was this helpful?
Thank you for voting!
Ice maker was leaking and had metal in the ice
3 of 4 people
found this instruction helpful.
-
Charles from Newark, DE
- Easy
- 15 - 30 mins
-
Nutdriver
Removed the screws and disconnected the electric. I put the proper electric harness on and went to fit the unit in but it didn't fit. Until I figured out that you have to use the clips from the old unit that hold the unit in place. The actually hang on them. Once I figured it out it was easy.
Was this helpful?
Thank you for voting!
ice maker faulty
3 of 4 people
found this instruction helpful.
-
Lloyd from Troup, TX
- Really Easy
- 15 - 30 mins
-
Socket set
removed three screws pluged it in and it was ready to go. I must add That I ordered it one day and received it the next day by fed ex. I could not believ how fast the service was also the new icemaker is working great. I will order any furture parts I need from Parts Select. Also have given your web site ot several other people. Thank you
... Read more
very much.
Read less
Was this helpful?
Thank you for voting!
Ice maker quit making ice--had to either be a faulty switch in the ice maker or a faulty water valve. I guessed it was the ice maker switch and ended up being correct.
3 of 4 people
found this instruction helpful.
-
Harvey from Port Tobacco, MD
- Really Easy
- 15 - 30 mins
-
Wrench set
It was exactly as everyone else described--remove old ice maker, unplug, plug in new ice maker, attach new ice maker. 3 screws, 1 plug. My plug was the one on the ice maker not on the refrigerator (ie I used the wiring/plug that was already in the freezer).
Was this helpful?
Thank you for voting!
the light socket broke apart
4 of 7 people
found this instruction helpful.
-
Elyse from Skokie, IL
- Really Easy
- 15 - 30 mins
-
Screw drivers
I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.
Was this helpful?
Thank you for voting!
Refrigerator quit cooling and the freezer wasn't freezing anything
4 of 7 people
found this instruction helpful.
-
Tonya from Grand Prairie, TX
- Really Easy
- 15 - 30 mins
-
Socket set
Order the part from the Internet on Sunday, it mailed out on Monday and I received it on Tuesday. I unplugged the fan then undone 3 screws that held the fan bracket to the refrigerator pulled it out unscrewed 3 more nuts and replaced the fan on the bracket and I cut the old wire plug off the old fan and with 2 wire nuts put it on my new f
... Read more
an. Replaced the fan and bracket back on the refrigerator plugged it in and it works like a new refrigerator.
Read less
Was this helpful?
Thank you for voting!
ice maker not functioning
2 of 2 people
found this instruction helpful.
-
philip from carlsbad, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver
I loosened the two screws on which the ice makers hangs and removed the third screw toward the back. I lifted the icemaker a bit and removed the part and unplugged the unit at rear. I reversed the process to install the new one. All very simple.
At first nothing happened, no water filling the tray. I thought there must be some ... Read more other problem. A few hours later I heard ice being dumped into the ice container. I don't understand the delay but it works fine.
At first no
At first nothing happened, no water filling the tray. I thought there must be some ... Read more other problem. A few hours later I heard ice being dumped into the ice container. I don't understand the delay but it works fine.
At first no
Read less
Was this helpful?
Thank you for voting!
Ice Maker started acting up
2 of 2 people
found this instruction helpful.
-
Bill from Sumas, WA
- Easy
- 15 - 30 mins
-
Nutdriver
I removed the 2 screws on top and the one screw underneath holding the Ice Maker to the wall of freezer.I pulled the electrical connection from the wall next (wiggled it back and forth until it came out).
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts ... Read more to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts ... Read more to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks
Read less
Was this helpful?
Thank you for voting!
Lower hinge on freezer door on side-by-side broke
2 of 2 people
found this instruction helpful.
-
Paul from Amherst, MA
- Easy
- 15 - 30 mins
-
Screw drivers, Wrench set
Removed the cover plate on top. Used a wrench and the nut driver to remove the three screws & the screw holding the grounding wire. Pulled apart the plastic coupling for the wiring to light the freezer. Then with the aid of a friend - lifted the door (with food removed from door shelves) off the hinge. This freezer had a water line wh
... Read more
ich we didin't know how to disconnect so we were careful to move the door slightly away from the broken hinge, set it on a stool with one person holding the door steady while the other person installed the new hinge piece. Definitely takes two people (as suggested in the directions) to both lift and guide the door into place. Once it was in place - I reinserted the screws up top and tightened them. Then had to untighten them to get the door to line up as it should vertically - so I would suggest just lighten tighen the upper screws until the door is aligned and swinging smoothly. Then reattached ground wire and plastic coupling. Works great.
Read less
Was this helpful?
Thank you for voting!
Door Closing Cam Kit Failed
2 of 2 people
found this instruction helpful.
-
Digger from Marysville, WA
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
Removed all of the food from the door by lifting the shelves out. Unbolted the top door hinge, and lifted the door off. Replaced the cam and placed the door back on, re-bolted the top hinge and placed all of the food and shelving back into the door. The door closes and seals when it is shut.
Was this helpful?
Thank you for voting!
Bad fan motor
3 of 5 people
found this instruction helpful.
-
Mark from Farmington Hills, MI
- Easy
- 15 - 30 mins
-
Nutdriver
Pop off six mounting screws and the ground screw. Remove the fan blade and reattach. Reinstall. Save yourself big bucks.
Was this helpful?
Thank you for voting!
Faulty light socket
3 of 5 people
found this instruction helpful.
-
Larry from HOUSTON, TX
- Very Easy
- 15 - 30 mins
-
Screw drivers
Followed the video instructions.
Was this helpful?
Thank you for voting!