- Home
- 1068539611
- Instructions
1068539611 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice Maker started acting up
2 of 2 people
found this instruction helpful.
-
Bill from Sumas, WA
- Easy
- 15 - 30 mins
-
Nutdriver
I removed the 2 screws on top and the one screw underneath holding the Ice Maker to the wall of freezer.I pulled the electrical connection from the wall next (wiggled it back and forth until it came out).
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts ... Read more to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts ... Read more to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks
Read less
Was this helpful?
Thank you for voting!
Machine Leaking Water
2 of 2 people
found this instruction helpful.
-
Frank from BERKELEY HTS, NJ
- Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
I did some tests and determined that the tub-to-pump drain hose had a leak in it.I then looked on the web to find disassembly instructions. I have a stacked washer dryer combination in a very confined space. The repair involved disconnecting both the washer and dryer from the water, gas, electric and venting systems first, then unstacking
... Read more
the dryer from the washer (not so easy, it required a helper). The machine was then pulled out so I could get at the parts necessary to remove the outside components and sheet metal. Then, I disassembled the top, front and access panel in the back. The disassembly went very well. I got access to the drain hose assembly and removed it fairly easily. I ordered a replacement drain hose assembly and found that installing the large port of the assembly was very difficult. (The two other ports were easy.) After thinking about it, I tilted the machine back a bit so I could try it from the bottom. That worked fine.I then reassembled and tested the machine. No leaks. Good luck with yours!
Read less
Was this helpful?
Thank you for voting!
Fan was noisy - bearing had failed
2 of 2 people
found this instruction helpful.
-
Karl from Wellesley, MA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver
It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.
Was this helpful?
Thank you for voting!
Water starting coming out of the ice maker uncontrolable - ice maker was broken
2 of 2 people
found this instruction helpful.
-
Nicole from Fishkill, NY
- Really Easy
- Less than 15 mins
-
Nutdriver
removed the three screws holding the old ice maker in place - unpluged the electronics .... took the new ice maker pluged in the electronics screwed in into place and we were in business and had ice within an hour.
Was this helpful?
Thank you for voting!
My Kenmore Ice Maker stopped manufacturing ice
3 of 5 people
found this instruction helpful.
-
Kenneth from Philadelphia, PA
- Really Easy
- Less than 15 mins
-
Nutdriver
The repair was very easy. I ordered the part from Part Seelect and the delivery was very quick.
Opened the box and took out the new ice maker. Emptied the freezer, turned off the power and the water to the Refigerator / Freezer / Iceww Maker. Used a quarter inch nut driver to remove the old ice make. Really easy remove one scre ... Read more w and lewsen two ther screws. unplugged the wiring harness. Took the bale arm off old unit and installed it on the new unit. Check to make sure I had the right wiring harness installed on the ic make which it was. Installed and leveled the new unit. in a little over a hour I had ice. Had to make a few adjustments to the water level setting to make sure all ice cube trays filled up completely.
So easy to do a cave man could do it.
Opened the box and took out the new ice maker. Emptied the freezer, turned off the power and the water to the Refigerator / Freezer / Iceww Maker. Used a quarter inch nut driver to remove the old ice make. Really easy remove one scre ... Read more w and lewsen two ther screws. unplugged the wiring harness. Took the bale arm off old unit and installed it on the new unit. Check to make sure I had the right wiring harness installed on the ic make which it was. Installed and leveled the new unit. in a little over a hour I had ice. Had to make a few adjustments to the water level setting to make sure all ice cube trays filled up completely.
So easy to do a cave man could do it.
Read less
Was this helpful?
Thank you for voting!
door making loud noise when opening or closing
2 of 2 people
found this instruction helpful.
-
phil from cocoa, FL
- Really Easy
- Less than 15 mins
-
Socket set
remove door, replace cam, replace door
Was this helpful?
Thank you for voting!
Ice maker quit. Got water out of ice dispenser
2 of 2 people
found this instruction helpful.
-
Melvin from Girard, IL
- Really Easy
- Less than 15 mins
-
Socket set
Wathced video (VERY helpful)of how to do repair to make sure it was within my capabilities to do. Made sure I had all requested numbers before ordering. Replacement part was an EXACT fit. 15 minutes of work and I saved nearly $150 of estimate by local service company. I am (and will continue to be) a repeat customer. Thanks. Mel
Was this helpful?
Thank you for voting!
The ice maker stopped making ice
2 of 2 people
found this instruction helpful.
-
Terry from Felton, PA
- Really Easy
- Less than 15 mins
-
Socket set
I removed the two attachment screws and lifted the old icemaker out and disconnected the plug. The new one was identical to the old one so the installation was just a reversal of the removal. The water soleniod was sticking from not being used so I took it apart and cleaned it. The next morning I had ice. The part arrived at my door in le
... Read more
ss than 24 hours from my order placement.
Read less
Was this helpful?
Thank you for voting!
Cimpressor would not start
5 of 11 people
found this instruction helpful.
-
Oliver from Madison, AL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Checked compressor with amp meter, and found it was not running, found Overload Switch bad.
When removing old switch watch carefully which lug you move wires from, so you will know which
lug to put the new switch on.
BE SURE YOU KNOW SOMETHING ABOUT
ELECTRICITY!!
When removing old switch watch carefully which lug you move wires from, so you will know which
lug to put the new switch on.
BE SURE YOU KNOW SOMETHING ABOUT
ELECTRICITY!!
Was this helpful?
Thank you for voting!
Icemaker was leaking whenever icemaker was set to on position
2 of 2 people
found this instruction helpful.
-
Yvette from RSM, CA
- Very Easy
- 15 - 30 mins
-
Socket set
We followed the video on the KitchenAid website. We turned off water valve at the wall, unplugged the refrigerator, removed the old icemaker by unscrewing the three mounting screws. We unplugged old icemaker from electrical source at back of refrigerator freezer compartment and removed it. We detached the on/off bar from the old icemak
... Read more
er and installed it on the new icemaker. The new icemaker fit perfectly. We plugged in the electric wire to the existing power cord at the back of the refrigerator freezer compartment. We placed the new icemaker in the same position as the old, making sure the mounting screw holes were aligned. Plugged refrigerator back in and turned on the water. Works beautifully.
Read less
Was this helpful?
Thank you for voting!
Faulty light socket
3 of 5 people
found this instruction helpful.
-
Larry from HOUSTON, TX
- Very Easy
- 15 - 30 mins
-
Screw drivers
Followed the video instructions.
Was this helpful?
Thank you for voting!
My White Drive Gear was clearly broken
2 of 2 people
found this instruction helpful.
-
Debbie from RAINBOW CITY, AL
- Very Easy
- Less than 15 mins
-
Screw drivers
I used a phillips screw driver, took the old one off, replaced the new one and it worked immediately!!! Didn't have to turn anything off...fixed in 5 minutes for $11. Fantastic Experience and my husband was shocked. No repairman bill.
Was this helpful?
Thank you for voting!
Ice maker did not make ice
2 of 2 people
found this instruction helpful.
-
Alfred from CANTERBURY, CT
- Very Easy
- 15 - 30 mins
-
Nutdriver
Ordered new ice maker from this site . Installation was very easy. Was happy to see that many electrical plugs were included. Chose the correct electrical plug and installed in 30 minutes. One note, be patient as it takes a while for ice maker to produce ice. When I heard the sound of ice dropping in the bin, I was very happy. Just in tim
... Read more
e for summer cold drinks. :)
Read less
Was this helpful?
Thank you for voting!
Unit wasn't producing ice
2 of 2 people
found this instruction helpful.
-
Michael from Ocoee, FL
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
It actually took me longer to think about the repair than actually doing it. It was three screws, two upper that you just loosen and then one on the bottom that you remove. Pulled the unit out and disconnected the power. Slipped the new unit onto the two upper brackets, after connecting the power cord, tightened the bracket screws, reatta
... Read more
ched the bottom set screw and I was making ice. Incredibly easy. When I ordered the replacement unit they said it would arrive in 3-5 days, but it only took a day and a half. Great experience all the way through. I'm a customer for life.
Read less
Was this helpful?
Thank you for voting!
freezing water tube and frozen rotation bar whuch caused water to overflow and freeze inside freezer.
3 of 5 people
found this instruction helpful.
-
Donna from CUMBERLAND, RI
- Really Easy
- 15 - 30 mins
-
Nutdriver
put arm up to stop icemaker from creating new ice cubes. us nut driver to unscrew 3 of the nuts holding icemaker in place do not completely remove the 2 top screws. lift off the screws and unplug from inside wire connection...make sure water tub is removed and frig unplugged. clean off ice anywhere inside freezer...take out new icemake
... Read more
r and connect wire plug...attach icemaker on to the 2 top screws...use nut driver to tighten into place. add and tighten bottom screw...leave arm down...replace clean and dried water tube into back and make sure it slid into ice maker...tighten screws in back and attatch water hose to tube...plug frid back on slide back into place...will start making ice in an hr or so....
Read less
Was this helpful?
Thank you for voting!