1068539610 Kenmore Refrigerator - Instructions

All Instructions for the 1068539610
121 - 135 of 561

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Door Closing Cam Kit Failed
2 of 2 people found this instruction helpful.
  • Digger from Marysville, WA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed all of the food from the door by lifting the shelves out. Unbolted the top door hinge, and lifted the door off. Replaced the cam and placed the door back on, re-bolted the top hinge and placed all of the food and shelving back into the door. The door closes and seals when it is shut.
Was this helpful?
Thank you for voting!
Fan was noisy - bearing had failed
2 of 2 people found this instruction helpful.
  • Karl from Wellesley, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver
It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.
Was this helpful?
Thank you for voting!
Machine Leaking Water
2 of 2 people found this instruction helpful.
  • Frank from BERKELEY HTS, NJ
  • Difficult
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
I did some tests and determined that the tub-to-pump drain hose had a leak in it.I then looked on the web to find disassembly instructions. I have a stacked washer dryer combination in a very confined space. The repair involved disconnecting both the washer and dryer from the water, gas, electric and venting systems first, then unstacking the dryer from the washer (not so easy, it required a helper). The machine was then pulled out so I could get at the parts necessary to remove the outside components and sheet metal. Then, I disassembled the top, front and access panel in the back. The disassembly went very well. I got access to the drain hose assembly and removed it fairly easily. I ordered a replacement drain hose assembly and found that installing the large port of the assembly was very difficult. (The two other ports were easy.) After thinking about it, I tilted the machine back a bit so I could try it from the bottom. That worked fine.I then reassembled and tested the machine. No leaks. Good luck with yours!
Was this helpful?
Thank you for voting!
Ice Maker started acting up
2 of 2 people found this instruction helpful.
  • Bill from Sumas, WA
  • Easy
  • 15 - 30 mins
  • Nutdriver
I removed the 2 screws on top and the one screw underneath holding the Ice Maker to the wall of freezer.I pulled the electrical connection from the wall next (wiggled it back and forth until it came out).
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks
Was this helpful?
Thank you for voting!
Bad fan motor
3 of 5 people found this instruction helpful.
  • Mark from Farmington Hills, MI
  • Easy
  • 15 - 30 mins
  • Nutdriver
Pop off six mounting screws and the ground screw. Remove the fan blade and reattach. Reinstall. Save yourself big bucks.
Was this helpful?
Thank you for voting!
Stopped making ice. Black stuff coming out on ice
2 of 2 people found this instruction helpful.
  • Paul from Navarre, FL
  • Easy
  • Less than 15 mins
  • Nutdriver
First I removed the (3) screws holding the unit to the side of freezer wall with a nutdriver. Then I disconnect the Harness from the back of the freezer. You have to work the Harness off connector because it was very tight. The Unit came with the correct harness installed so I reconnected the harness to the Freezer and replaced the (3) sc rews. I had ice in about 2.5 hours.
Was this helpful?
Thank you for voting!
Ice maker quit, I cross wired the two solenoid valves and determined the valvles were not the problem.
2 of 2 people found this instruction helpful.
  • michael from naples, FL
  • Easy
  • Less than 15 mins
  • Nutdriver
Used a nutdriver and removed the lower mount nut, then loosened the the top two nuts and the icemaker lifted off, then unplugged the device and replugged it into the "old" plug(the new ones were not needed) then remounted it. Then it did not fill (as others posted happened right away.) Some poster suggested manually filling the tray so I did it. Later it froze and emptied and refilled and started working normally. Not sure if putting water had anything to do with it or it just took some time. It would be nice if the instructions addressed this issue.
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people found this instruction helpful.
  • Yafa (and David) from Bothell, WA
  • Easy
  • Less than 15 mins
  • Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
fridge door switch did not work
2 of 2 people found this instruction helpful.
  • stu from richmond, VA
  • Easy
  • Less than 15 mins
  • Socket set
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.
Was this helpful?
Thank you for voting!
Ice maker went bad
3 of 5 people found this instruction helpful.
  • DENNIS from SOUTH LYON, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Took the old one out in Two Min's, Replaced with the new one in about the same time.
Had ice within 1 hour
Was this helpful?
Thank you for voting!
Door light switch disintegrated
2 of 2 people found this instruction helpful.
  • Thomas from Roseville, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Very simple fix, remove 3 screws, two connectors to the old switch
Was this helpful?
Thank you for voting!
Unit froze up with ice in the cube maker
2 of 2 people found this instruction helpful.
  • John from Mesa, AZ
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Just like the others. Unplug the refrigerator. Loosen the top two screw and remove the bottom screw. Unplug the unit, plug in the new one, slid the unit over the top two screws, replace the bottom screw and tighten the top two screws. Done. I ordered the unit Sunday it was shipped Monday and arrived Phoenix Wednesday, shipper then re routed it to Tucson Thursday who sent it back to Phoenix on Friday and finallydelivered it Saturday.
Was this helpful?
Thank you for voting!
Ice maker failed
2 of 2 people found this instruction helpful.
  • Kim from Palo Alto, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Super easy! I read all these posts but here are a couple helpful hints -

1. to remove the old icemaker definitely remove the one lower screw but then unscrew the top two screws only half way. The top screw holes on the old and new icemakers are triangle shaped so the old icemaker will simply lift off the half-unscrewed top scr ews. This makes reinstallation SO much easier.

2. carefully lower the loose icemaker enough to disconnect the wiring harness from the fridge and remove the old icemaker.

3. On installation the one thing to be careful with is the positioning of the fill tube. It's easier if it's in place when you reconnect the harness of the new icemaker because the harness is only as long as it must be.
4. hang the new icemaker on the half unscrewed top screws, snug them up, install the lower screw and flip the wire ice level sensor arm down.

I didn't even turn the water off because only a working icemaker can turn the water valve on and off.

Plugged in the power to the fridge and within an hour water filled the tray. By morning I had 2-3 batches of fresh ice in the bucket. Super easy.
Was this helpful?
Thank you for voting!
old part cracked and broke
2 of 2 people found this instruction helpful.
  • Paul from Green Valley, AZ
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
easy - remove the door, replace th part, put back the door
Was this helpful?
Thank you for voting!
The ice maker quit producing ice.
2 of 2 people found this instruction helpful.
  • Robert from Spring Valley, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
First I removed the ice bin to give me room to work. Then I took out the screws that held the old ice maker in place. I disconnected the wiring. I then plugged the wires of the new ice maker into the old wiring harness. I put in the bottom screws and loosely connected the top screws. I checked the level of the ice maker with a small l evel and then tightened the screws. The nest thing was to install wire level that shuts off the ice maker when the bin is full. Finally put the ice bin back in place.
Was this helpful?
Thank you for voting!
All Instructions for the 1068539610
121 - 135 of 561