1068439521 Kenmore Refrigerator - Instructions

All Instructions for the 1068439521
121 - 135 of 249

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
light did not work on the refrigerator side
1 of 2 people found this instruction helpful.
  • David from GROVESPRING, MO
  • Easy
  • Less than 15 mins
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what i s inside the refer!
Was this helpful?
Thank you for voting!
door was not closing
1 of 2 people found this instruction helpful.
  • Joe from Saint George, UT
  • Really Easy
  • Less than 15 mins
  • Socket set
Removed all the adjustable shelves inside the door. Removed the top hinge cover (1 nut). then the top hinge bracket (3 nuts). The door doesn't weight very much so you shouldn't have to worry about the door just falling off after you remove the top hinge. then simply lift the door off the bottom hinge and carefully lay it down. One nu t in each of the plastc cams on the bottom of the door and an easy swap out with the new parts. A little vaseline one at least one of the surfaces of the cam, reverse the order and simply put things back together and your good to go. Door closes on its own like new. You might as well get both parts for the lower cam and swap them out simultaniously since you have the door off. PLEAS NOTE: Yes there are two different parts for this repair.
Was this helpful?
Thank you for voting!
door sounded like it was craking when trying to close
1 of 3 people found this instruction helpful.
  • Randall from Bradenton, FL
  • Really Easy
  • Less than 15 mins
  • Wrench set
took all items out of the door, used a wrench to undue the bolts, pulled the door off and placed the new part on the bottom of the door. kept the other new parts that came with the one I needed. very simple
Was this helpful?
Thank you for voting!
Refrigerator would not stay cold
2 of 6 people found this instruction helpful.
  • Jeremy from State College, PA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Wrench set
Removed rear cover to see non-operating fan - removed three mounting screws on the motor that were a challenge to access. Swapped fan from old motor onto new motor - one threaded nut on the motor shaft. Spliced new fan wires into fan wires of the wiring harness and mounted with three self-tapping screws supplied with new fan motor. Repl aced rear cover and plugged it in! Now the refrigerator cools like new (1981 model side-by-side Admiral)
Was this helpful?
Thank you for voting!
The door gasket was very hot which is caused by an overheated expansion line that runs along the area of the door gasket. This was caused by a failed cooling fan motor.
2 of 6 people found this instruction helpful.
  • James from Howell, MI
  • Easy
  • 30 - 60 mins
  • Nutdriver
Pulled out the refrigerator and removed the two panels from the rear of the refrigerator. Removed the fan held in by four screws and unplugged the connector. Soldered on the original connector, installed the fan to the motor and re-installed the unit into the refrigerator. Then blew out and vaccumed the condenser coils.
Was this helpful?
Thank you for voting!
burned oven bulb
3 of 9 people found this instruction helpful.
  • Ivanka from Atlantra, GA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh t bulb in was not the problem.
Was this helpful?
Thank you for voting!
Hinges were making a popping sound and did not close properly
0 of 1 people found this instruction helpful.
  • John from Titusville, FL
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
I followed the video instructions available on the net. Hardest part of the job was getting up off the floor after I disconnected the water line. I'm 90 years old
Was this helpful?
Thank you for voting!
After Hurricane Irene refrigeration compressore did not start
1 of 4 people found this instruction helpful.
  • Bobby from New Bern, NC
  • Really Easy
  • 15 - 30 mins
  • Pliers, Screw drivers
Followed the directions. Installation was quick. Took loner to put the covers back on and push the applicance back in position than the repair.
Was this helpful?
Thank you for voting!
Replaced Cam For Closing Door.
0 of 1 people found this instruction helpful.
  • ROBERT from CASTAIC, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver
I'v used you 2 times for repairing my fridge and clothes dryer. . . . . So far you've saved me over a grand by doing it myself. . . Plus your service is nothing less than astounding. . . . . Both times I ordered early in the day and I got both orders the next day. . . . . You guys are sure on the ball. . . . . . Thanks
Was this helpful?
Thank you for voting!
Broken wheel under fridge
0 of 1 people found this instruction helpful.
  • Ted from Magnolia, TX
  • Really Easy
  • 15 - 30 mins
  • Socket set
Replaced both since they came as a set. The only way it could have been any easier is if I had the wife do it. She had the remote this time. (•¿•)
Was this helpful?
Thank you for voting!
Broken Kickplate Support Clip (Left side)
0 of 1 people found this instruction helpful.
  • William from Fountain Valley, CA
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
Unscrewed old broken part from the kickplate and attempted to install the new clip. Mounting screws would not go into the new clip. Had to drill out the mounting holes in the plastic clip using a #30 drill bit. Once the new clip was mounted, attempted to snap the kickplate back in place. Unfortunately at the left side the kickplate would not fully mate with the metal clip on the refrigerator body and would not snap all the way back to the refrigerator front surface, as the right side does. At least the kickplate doesn't fall down onto the floor on the left side as it did before. I suspect there is an alignment problem with the left side refrigerator metal clip, but have not pursued that yet.
Was this helpful?
Thank you for voting!
refrigerator door did not seal and was out of alignment
0 of 1 people found this instruction helpful.
  • joseph from haddon heights, NJ
  • Easy
  • 30 - 60 mins
  • Nutdriver, Socket set
I was quoted $212.00 by a service co. to make this repair. When I investigated online @ Part Select, they had all of the parts shown on schematics of each section of the refrigerator/freezer (side by side)with part numbers shown. It was easy to find the necessary parts.The cam kit came as a package for both doors and cost $12.00 plus ship ping. Installation instructions were included.It took me an kour to make the repair. The hardest part was removing all the condiments from the shelves and remembering from which shelf they had to be returned. Net savings $200.00
Was this helpful?
Thank you for voting!
Did not work light does not come on when the door opens. Would try the light socket. It not sure how good the switch got plugged in.
1 of 4 people found this instruction helpful.
  • Cherilyn from CARROLLTON, TX
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
By watching a video.
Was this helpful?
Thank you for voting!
the front wheel broke
0 of 1 people found this instruction helpful.
  • Mary from Pelham, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
First I had to tilt the refrigerator on wood on the supports under the refrigerator, the wheels were easy to get to then I unscrewed the old ones and replaced them with the new better wheels. The old ones where plastic.
Was this helpful?
Thank you for voting!
Broken light switch
0 of 1 people found this instruction helpful.
  • George from North Scituate, RI
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Part was easy to order, delivered quickly, installation very easy. Just unplug the unit, pop out the old swich using a screwdriver, disconnect and reconnect leads and pop switch back in. Definitely recommend that you can do it too.
Was this helpful?
Thank you for voting!
All Instructions for the 1068439521
121 - 135 of 249