1068432421 Kenmore Refrigerator - Instructions

All Instructions for the 1068432421
106 - 120 of 268

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Connection leaked as tube entered freezer
1 person found this instruction helpful.
  • Robert from MERRIMACK, NH
  • Very Easy
  • 15 - 30 mins
Followed video and had one problen, the metal pipe would not release as shown,so I used a hacksaw between the plastic and metal pipe, removing the metal pipe from inside as the video shows. Good instructions.
Was this helpful?
Thank you for voting!
Door would not close wright
1 person found this instruction helpful.
  • cecil from ATASCADERO, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
Remove top henge, lift door off bottom henge, take off old plastic closer put on new one. Door works great now
Was this helpful?
Thank you for voting!
fridge making bad noise
2 of 4 people found this instruction helpful.
  • Kevin from LEVAN, UT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
Removed cover change mounting bracket on fan put it back in works great
Was this helpful?
Thank you for voting!
Light switch broke
2 of 4 people found this instruction helpful.
  • Carolee from Spokane Valley, WA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Pried out old part with screwdriver. Unplugged. When new part came, just plugged it in and pushed the part into place.
Was this helpful?
Thank you for voting!
Broken wheel on leveling roller
2 of 4 people found this instruction helpful.
  • Max from Jonesboro, AR
  • Really Easy
  • Less than 15 mins
  • Socket set
I removed one bolt and took out the old roller after first blocking up the fridge. Then I was puzzled for a moment because the hole in the new assembly was not tapped. But then I saw that the old bolt was a self tapping bolt. I used it to tap the hole then removed it and installed the new assembly. No sweat job.
Was this helpful?
Thank you for voting!
Refrigerator door would not close properly
1 person found this instruction helpful.
  • Frederick from Spokane Valley, WA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Removed the top hinge cap. Removed the 3 screws with a nutdriver. Lifted the door off of the bottom hinge and placed it on it's side. Then I removed both closing cams (one screw holding each). Clean the area then replaced each cam. I put some vaseline on the bottom cam and replaced the door. 4-5 minutes not counting removing and repla cing the food inside the door shelves. I'm 56 years old and have always done most of my own handywork. I don't remember any job going so smooth and fast! Ever!
Was this helpful?
Thank you for voting!
The Light Socket Burned Out.
5 of 13 people found this instruction helpful.
  • MATTHEW from STOCKTON, CA
  • Really Easy
  • Less than 15 mins
I pulled the socket out and unplugged the wires. I replaced the light socket by plugging in the wires and snapping the light socket into place. A very simple fix.
Was this helpful?
Thank you for voting!
Condenser fan motor froze up
2 of 4 people found this instruction helpful.
  • Douglas from Mesa, AZ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Unplug fridge, unpluged fan motor from plug socket, removed bracket screws, removed fan retainer clip from shaft. removed screws holding fan to bracket
Was this helpful?
Thank you for voting!
Condenser fan making noise
2 of 4 people found this instruction helpful.
  • Richard from North Easton, MA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Wrench set
I removed 7 screws hold the heavy cardboard cover on the rear of the fridge. The dificult part was taking the screws that hold the 3 fan motor braces on the fan out. After that it was a matter of making the wire conections and putting it back in. I did not have enough room to laydown to do the work, If i had it would have been a lot easi er to see the screws that had to be removed. All in all an easy job, and the part was a perfect fit.
Was this helpful?
Thank you for voting!
original motor stopped
2 of 4 people found this instruction helpful.
  • Paul from Lowell, MI
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Socket set
removed old and instaslled new. biggest problem was getting to one of the screws.
Was this helpful?
Thank you for voting!
door not closing right
1 of 2 people found this instruction helpful.
  • kenneth from soddy daisy, TN
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
repair was easy. watch the video
Was this helpful?
Thank you for voting!
Freezer door would not shut without a re-enforced push
1 of 2 people found this instruction helpful.
  • Earl from Sandy, UT
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers, Socket set
I followed your on line video, that was a fantastic help. Easy as 1,2,3. I used the tools he recommended and followed his steps. I replaced the cam on the door and on the bottom pin, its works like new.
Was this helpful?
Thank you for voting!
refregerator would not close by itself
1 of 2 people found this instruction helpful.
  • Joseph from Scottsdale, AZ
  • Really Easy
  • 15 - 30 mins
  • Screw drivers, Socket set, Wrench set
Your on line video was fantastic, it led me all the way through the repair. As they say, "A picture or video is worth 1000 words". I wish everyone had instructions like you. Great Job!!!
Was this helpful?
Thank you for voting!
cooling fan quit
1 of 2 people found this instruction helpful.
  • George from Belhaven, NC
  • Easy
  • 30 - 60 mins
  • Nutdriver
Ordered new fan motor on line took out old motor and replaced with new one
Was this helpful?
Thank you for voting!
Condenser Fan Failure
2 of 5 people found this instruction helpful.
  • Al from Tonka Bay, MN
  • Easy
  • 30 - 60 mins
  • Socket set
Partition between Freezer and Fridge was running very hot. (Warm is normal). Oiling fan did not work. The only problems encountered in the replacement were getting fan out and in through coolant lines, cut plug off to accomodate generic fan wiring, getting the screws back in without cooking your hand on a hot compressor. Unit works great !
Was this helpful?
Thank you for voting!
All Instructions for the 1068432421
106 - 120 of 268