1068261 Kenmore Freezer - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
light would work intermitently
0 of 1 people
found this instruction helpful.
-
Gregory from middle island, NY
- Easy
- Less than 15 mins
-
Screw drivers
removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.
Was this helpful?
Thank you for voting!
Broken light switch
0 of 1 people
found this instruction helpful.
-
George from North Scituate, RI
- Really Easy
- Less than 15 mins
-
Screw drivers
Part was easy to order, delivered quickly, installation very easy. Just unplug the unit, pop out the old swich using a screwdriver, disconnect and reconnect leads and pop switch back in. Definitely recommend that you can do it too.
Was this helpful?
Thank you for voting!
rocker switch broke off
0 of 1 people
found this instruction helpful.
-
STANLEY from OAKLAND, NJ
- Really Easy
- Less than 15 mins
-
Screw drivers
disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.
Was this helpful?
Thank you for voting!
Very Easy
0 of 1 people
found this instruction helpful.
-
Clint from Idaho Falls, ID
- Really Easy
- Less than 15 mins
-
Nutdriver
Like most have stated this is a simple job. Nut-driver and six screws (on mine). Less than ten minutes. Like someone else said the hardest part was unloading the door.
Was this helpful?
Thank you for voting!
Lower door parts failed
0 of 1 people
found this instruction helpful.
-
Thomas from West Chester, OH
- Really Easy
- Less than 15 mins
-
Screw drivers, Socket set
took door of and replaced ,no problem
Was this helpful?
Thank you for voting!
My cam on the bottom of the refrigerator door broke and also the door stop broke
0 of 1 people
found this instruction helpful.
-
Martin from Safford, AZ
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
I followed the video that you have for this part and it was very easy to repair. The video that you put together showing how to do the repair, made the job very simple, and your service was outstanding. What a great web site!!! Thanks
Was this helpful?
Thank you for voting!
refrig warm door cam broken
0 of 1 people
found this instruction helpful.
-
Richard from Boca Raton, FL
- Easy
- Less than 15 mins
-
Nutdriver
Follow instructions from owners manual. top hinge first then move door upward and replace broken cam with new parts
Was this helpful?
Thank you for voting!
Door just wouldn't close and sometimes stopped just close enough that it looked closed and ran all night
0 of 1 people
found this instruction helpful.
-
Cynthia from bethlehem, PA
- Really Easy
- Less than 15 mins
-
Nutdriver
It was so easy I could have done the video. Many thank you's for saving me $79.00 in house call fees.... cindi
Was this helpful?
Thank you for voting!
Internal light did not come on each time the door was opened.
0 of 1 people
found this instruction helpful.
-
John from Jefferson Hills, PA
- Really Easy
- Less than 15 mins
After disconnecting the electricity. I followed the instructions as indicated in the "HOW TO" article on the website. I used a steel putty knife and pried the light switch out of its retaining hole. I worked the right side the most since this is the side with the retaining clip. After I removed the switch I transferred the two electrical
... Read more
outlets to the new switch and easily snapped it into place. Engaged the electric power and tested the switch.
Read less
Was this helpful?
Thank you for voting!
refrigerator door would not stay closed
0 of 1 people
found this instruction helpful.
-
steve from spotsylvania, VA
- Easy
- 15 - 30 mins
-
Socket set
Just as shown on a you tube video showing the steps involved, except I did not need to drill and tap the hole in the door. Cam repair kit contained all the correct parts.Freezer door is still working fine so I did not need to repair that door.
Was this helpful?
Thank you for voting!
Replaced Cam For Closing Door.
0 of 1 people
found this instruction helpful.
-
ROBERT from CASTAIC, CA
- Easy
- 15 - 30 mins
-
Nutdriver
I'v used you 2 times for repairing my fridge and clothes dryer. . . . . So far you've saved me over a grand by doing it myself. . . Plus your service is nothing less than astounding. . . . . Both times I ordered early in the day and I got both orders the next day. . . . . You guys are sure on the ball. . . . . . Thanks
Was this helpful?
Thank you for voting!
Original cam broke into 3 pieces
0 of 1 people
found this instruction helpful.
-
Tom from Columbai, MD
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Part arrived overnight. The How-To video at PartSelect showed the procedure exactly. It took about 30 minutes.
Was this helpful?
Thank you for voting!
light staying on
0 of 1 people
found this instruction helpful.
-
Cecelia from Beaver Dam, WI
- Easy
- 15 - 30 mins
-
Screw drivers
A very cold and brittle switch in a 17 year old fridge. Used screwdrivers to pry out with some resistance Had to cut the molded plug in half and split wires, because replacement contacts were farther apart than the original. End result, works great.
Was this helpful?
Thank you for voting!
Door not closing tightly
0 of 1 people
found this instruction helpful.
-
Jess from Manchester, TN
- Really Easy
- 15 - 30 mins
-
Nutdriver
Removed the door, installed the lower cam & re-installed the door. Diagram & parts list correct. An easy repair.
Was this helpful?
Thank you for voting!
Hinges were making a popping sound and did not close properly
0 of 1 people
found this instruction helpful.
-
John from Titusville, FL
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
I followed the video instructions available on the net. Hardest part of the job was getting up off the floor after I disconnected the water line. I'm 90 years old
Was this helpful?
Thank you for voting!