1068139321 Kenmore Refrigerator - Instructions

All Instructions for the 1068139321
121 - 135 of 526

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Original ice maker quit making ice, leaked water.
2 of 2 people found this instruction helpful.
  • John from Yorba Linda, CA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Removed the old ice maker (2 screws, about 2 minutes). Read the excellent instructions. Prepped the replacement unit by adding the mount bracket. It plugged straight into the existing fridge wiring harness. Amazing how standardized icemakers are! Total time for a very careful job was under an hour.

It came in the mail, I got home about 5pm and had it installed that evening before dinner. First load of ice was in the catcher before I went to bed.

Very nice kit, and economical compared to a new fridge!
Was this helpful?
Thank you for voting!
ice maker not functioning
2 of 2 people found this instruction helpful.
  • philip from carlsbad, CA
  • Really Easy
  • 15 - 30 mins
  • Nutdriver
I loosened the two screws on which the ice makers hangs and removed the third screw toward the back. I lifted the icemaker a bit and removed the part and unplugged the unit at rear. I reversed the process to install the new one. All very simple.

At first nothing happened, no water filling the tray. I thought there must be some other problem. A few hours later I heard ice being dumped into the ice container. I don't understand the delay but it works fine.



At first no
Was this helpful?
Thank you for voting!
Ice Maker started acting up
2 of 2 people found this instruction helpful.
  • Bill from Sumas, WA
  • Easy
  • 15 - 30 mins
  • Nutdriver
I removed the 2 screws on top and the one screw underneath holding the Ice Maker to the wall of freezer.I pulled the electrical connection from the wall next (wiggled it back and forth until it came out).
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks
Was this helpful?
Thank you for voting!
Refrigerator coils froze up and 5 weeks later it got stuck in defrost.
2 of 2 people found this instruction helpful.
  • LES from GRAY, TN
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
The parts were reasonably priced, shipped promptly and received in a couple of days. I reviewed a YouTube video before starting that was beneficial. Huge savings over retail repair service. A+ replacement parts house and I would highly recommend.
Was this helpful?
Thank you for voting!
Fridge stopped cooling
3 of 5 people found this instruction helpful.
  • ray from palm bay, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I replaced the defrost relay folling instructions I read on the internet--and it still didn't work--So I replaced the compressor start relay which was easier than the defrost relay--it worked and the fridg is working good.
Was this helpful?
Thank you for voting!
Fan was noisy - bearing had failed
2 of 2 people found this instruction helpful.
  • Karl from Wellesley, MA
  • A Bit Difficult
  • 30 - 60 mins
  • Nutdriver
It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.
Was this helpful?
Thank you for voting!
Faulty light socket
3 of 5 people found this instruction helpful.
  • Larry from HOUSTON, TX
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Followed the video instructions.
Was this helpful?
Thank you for voting!
Icemaker was leaking whenever icemaker was set to on position
2 of 2 people found this instruction helpful.
  • Yvette from RSM, CA
  • Very Easy
  • 15 - 30 mins
  • Socket set
We followed the video on the KitchenAid website. We turned off water valve at the wall, unplugged the refrigerator, removed the old icemaker by unscrewing the three mounting screws. We unplugged old icemaker from electrical source at back of refrigerator freezer compartment and removed it. We detached the on/off bar from the old icemak er and installed it on the new icemaker. The new icemaker fit perfectly. We plugged in the electric wire to the existing power cord at the back of the refrigerator freezer compartment. We placed the new icemaker in the same position as the old, making sure the mounting screw holes were aligned. Plugged refrigerator back in and turned on the water. Works beautifully.
Was this helpful?
Thank you for voting!
My Kenmore Ice Maker stopped manufacturing ice
3 of 5 people found this instruction helpful.
  • Kenneth from Philadelphia, PA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
The repair was very easy. I ordered the part from Part Seelect and the delivery was very quick.
Opened the box and took out the new ice maker. Emptied the freezer, turned off the power and the water to the Refigerator / Freezer / Iceww Maker. Used a quarter inch nut driver to remove the old ice make. Really easy remove one scre w and lewsen two ther screws. unplugged the wiring harness. Took the bale arm off old unit and installed it on the new unit. Check to make sure I had the right wiring harness installed on the ic make which it was. Installed and leveled the new unit. in a little over a hour I had ice. Had to make a few adjustments to the water level setting to make sure all ice cube trays filled up completely.

So easy to do a cave man could do it.
Was this helpful?
Thank you for voting!
My White Drive Gear was clearly broken
2 of 2 people found this instruction helpful.
  • Debbie from RAINBOW CITY, AL
  • Very Easy
  • Less than 15 mins
  • Screw drivers
I used a phillips screw driver, took the old one off, replaced the new one and it worked immediately!!! Didn't have to turn anything off...fixed in 5 minutes for $11. Fantastic Experience and my husband was shocked. No repairman bill.
Was this helpful?
Thank you for voting!
Stopped making ice. Black stuff coming out on ice
2 of 2 people found this instruction helpful.
  • Paul from Navarre, FL
  • Easy
  • Less than 15 mins
  • Nutdriver
First I removed the (3) screws holding the unit to the side of freezer wall with a nutdriver. Then I disconnect the Harness from the back of the freezer. You have to work the Harness off connector because it was very tight. The Unit came with the correct harness installed so I reconnected the harness to the Freezer and replaced the (3) sc rews. I had ice in about 2.5 hours.
Was this helpful?
Thank you for voting!
Unit wasn't producing ice
2 of 2 people found this instruction helpful.
  • Michael from Ocoee, FL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
It actually took me longer to think about the repair than actually doing it. It was three screws, two upper that you just loosen and then one on the bottom that you remove. Pulled the unit out and disconnected the power. Slipped the new unit onto the two upper brackets, after connecting the power cord, tightened the bracket screws, reatta ched the bottom set screw and I was making ice. Incredibly easy. When I ordered the replacement unit they said it would arrive in 3-5 days, but it only took a day and a half. Great experience all the way through. I'm a customer for life.
Was this helpful?
Thank you for voting!
Ice maker quit, I cross wired the two solenoid valves and determined the valvles were not the problem.
2 of 2 people found this instruction helpful.
  • michael from naples, FL
  • Easy
  • Less than 15 mins
  • Nutdriver
Used a nutdriver and removed the lower mount nut, then loosened the the top two nuts and the icemaker lifted off, then unplugged the device and replugged it into the "old" plug(the new ones were not needed) then remounted it. Then it did not fill (as others posted happened right away.) Some poster suggested manually filling the tray so I did it. Later it froze and emptied and refilled and started working normally. Not sure if putting water had anything to do with it or it just took some time. It would be nice if the instructions addressed this issue.
Was this helpful?
Thank you for voting!
Water starting coming out of the ice maker uncontrolable - ice maker was broken
2 of 2 people found this instruction helpful.
  • Nicole from Fishkill, NY
  • Really Easy
  • Less than 15 mins
  • Nutdriver
removed the three screws holding the old ice maker in place - unpluged the electronics .... took the new ice maker pluged in the electronics screwed in into place and we were in business and had ice within an hour.
Was this helpful?
Thank you for voting!
Ice maker working with no production of ice
2 of 2 people found this instruction helpful.
  • Paul from East Northport, NY
  • Really Easy
  • 15 - 30 mins
  • Socket set, Wrench (Adjustable)
Turn off the water source and unplug freezer. Remove copper tube and then remove valve from back of refrigerator. Disconnect plastic tube and power connection. Mark power connection plug top with a "T", this reminder helps with the new valve. Plug power and plastic tube into new valve and screw assembly back into refrigerator. Using a wrench, connect copper tube into valve. Restore water source and plug back in in freezer. Within a couple hours, ice production was back.
Like the other repair stories (that helped me), this job was very easy.
Was this helpful?
Thank you for voting!
All Instructions for the 1068139321
121 - 135 of 526