1067698421 Kenmore Refrigerator - Instructions

All Instructions for the 1067698421
121 - 135 of 547

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice Maker Not Creating Ice Cubes
2 of 2 people found this instruction helpful.
  • Daniel from Albuquerque, NM
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
Removed Ice tray and flap followed by the three screws that held the old ice maker in place. (I probably didn't have to remove the top two, they are designed to just loosen and lift up on the mecanism to free.) I then pulled the old wiring harness out of the original ice maker. A small screw driver helped in depressing a tab while pulling on the harness. The same process was used to remove the wiring harness that was attached to the new replacement unit. I connected the original wiring harness that I had disconnected from the bad ice maker, and it fit perfectly into the replacement unit. No need to splice or use any of the harnesses that came with replacement. I tried installing the new unit and discovered that there was interfernce with the water feed hose. I had forgotten to break off the tab on the end of the replacement unit. Once I did that using pliers, the unit fit fine. I tightened the screws, installed the on/off mecanism and replaced the tray and flap. I then waited and waited, hoping to hear the forgotten sound of water entering the ice maker. Had a beer and walked the dogs thinking I had failed, but low and behold, over an hour later, the ice maker turned on the water. Many hours later, my wife woke me up in the middle of the night to declare we had cubes! Success.
Was this helpful?
Thank you for voting!
Original ice maker quit making ice, leaked water.
2 of 2 people found this instruction helpful.
  • John from Yorba Linda, CA
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
Removed the old ice maker (2 screws, about 2 minutes). Read the excellent instructions. Prepped the replacement unit by adding the mount bracket. It plugged straight into the existing fridge wiring harness. Amazing how standardized icemakers are! Total time for a very careful job was under an hour.

It came in the mail, I got home about 5pm and had it installed that evening before dinner. First load of ice was in the catcher before I went to bed.

Very nice kit, and economical compared to a new fridge!
Was this helpful?
Thank you for voting!
Ice Maker started acting up
2 of 2 people found this instruction helpful.
  • Bill from Sumas, WA
  • Easy
  • 15 - 30 mins
  • Nutdriver
I removed the 2 screws on top and the one screw underneath holding the Ice Maker to the wall of freezer.I pulled the electrical connection from the wall next (wiggled it back and forth until it came out).
I matched it up to the picture from this site and ordered the replacement unit.
When it arrived, it had a lot of extra parts to match up to mine and any other fridge.
A good tip is to keep the old unit so you can configure the new unit the same. Although it was easy, this took me the longest of the entire job. Once this was done, it took me !0 minutes to plug the new unit into my fridge and then attach it back to the wall with the 3 screws.Not a hard job.Thanks
Was this helpful?
Thank you for voting!
Bad fan motor
3 of 5 people found this instruction helpful.
  • Mark from Farmington Hills, MI
  • Easy
  • 15 - 30 mins
  • Nutdriver
Pop off six mounting screws and the ground screw. Remove the fan blade and reattach. Reinstall. Save yourself big bucks.
Was this helpful?
Thank you for voting!
Fridge stopped cooling
3 of 5 people found this instruction helpful.
  • ray from palm bay, FL
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I replaced the defrost relay folling instructions I read on the internet--and it still didn't work--So I replaced the compressor start relay which was easier than the defrost relay--it worked and the fridg is working good.
Was this helpful?
Thank you for voting!
The ice maker stopped making ice
2 of 2 people found this instruction helpful.
  • Terry from Felton, PA
  • Really Easy
  • Less than 15 mins
  • Socket set
I removed the two attachment screws and lifted the old icemaker out and disconnected the plug. The new one was identical to the old one so the installation was just a reversal of the removal. The water soleniod was sticking from not being used so I took it apart and cleaned it. The next morning I had ice. The part arrived at my door in le ss than 24 hours from my order placement.
Was this helpful?
Thank you for voting!
fridge door switch did not work
2 of 2 people found this instruction helpful.
  • stu from richmond, VA
  • Easy
  • Less than 15 mins
  • Socket set
I removed the switch housing (4 screws), replacing the switch in the housing was a snap. It took 5 minutes, cost $8 and light works like new!

Why didn't I order this part and do the repair earlier? Very simple.
Was this helpful?
Thank you for voting!
The ice maker quit producing ice.
2 of 2 people found this instruction helpful.
  • Robert from Spring Valley, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
First I removed the ice bin to give me room to work. Then I took out the screws that held the old ice maker in place. I disconnected the wiring. I then plugged the wires of the new ice maker into the old wiring harness. I put in the bottom screws and loosely connected the top screws. I checked the level of the ice maker with a small l evel and then tightened the screws. The nest thing was to install wire level that shuts off the ice maker when the bin is full. Finally put the ice bin back in place.
Was this helpful?
Thank you for voting!
Unit froze up with ice in the cube maker
2 of 2 people found this instruction helpful.
  • John from Mesa, AZ
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Just like the others. Unplug the refrigerator. Loosen the top two screw and remove the bottom screw. Unplug the unit, plug in the new one, slid the unit over the top two screws, replace the bottom screw and tighten the top two screws. Done. I ordered the unit Sunday it was shipped Monday and arrived Phoenix Wednesday, shipper then re routed it to Tucson Thursday who sent it back to Phoenix on Friday and finallydelivered it Saturday.
Was this helpful?
Thank you for voting!
Ice maker failed
2 of 2 people found this instruction helpful.
  • Kim from Palo Alto, CA
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Super easy! I read all these posts but here are a couple helpful hints -

1. to remove the old icemaker definitely remove the one lower screw but then unscrew the top two screws only half way. The top screw holes on the old and new icemakers are triangle shaped so the old icemaker will simply lift off the half-unscrewed top scr ews. This makes reinstallation SO much easier.

2. carefully lower the loose icemaker enough to disconnect the wiring harness from the fridge and remove the old icemaker.

3. On installation the one thing to be careful with is the positioning of the fill tube. It's easier if it's in place when you reconnect the harness of the new icemaker because the harness is only as long as it must be.
4. hang the new icemaker on the half unscrewed top screws, snug them up, install the lower screw and flip the wire ice level sensor arm down.

I didn't even turn the water off because only a working icemaker can turn the water valve on and off.

Plugged in the power to the fridge and within an hour water filled the tray. By morning I had 2-3 batches of fresh ice in the bucket. Super easy.
Was this helpful?
Thank you for voting!
Door light switch disintegrated
2 of 2 people found this instruction helpful.
  • Thomas from Roseville, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Very simple fix, remove 3 screws, two connectors to the old switch
Was this helpful?
Thank you for voting!
Replacing the bulb in the freezer side
5 of 11 people found this instruction helpful.
  • Yafa (and David) from Bothell, WA
  • Easy
  • Less than 15 mins
  • Nutdriver
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.
Was this helpful?
Thank you for voting!
Ice maker went bad
3 of 5 people found this instruction helpful.
  • DENNIS from SOUTH LYON, MI
  • Really Easy
  • Less than 15 mins
  • Nutdriver
Took the old one out in Two Min's, Replaced with the new one in about the same time.
Had ice within 1 hour
Was this helpful?
Thank you for voting!
Light didnt go on
3 of 5 people found this instruction helpful.
  • dorotea from staten island, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
The light rocker switch wasnt working. I found the part on the web site. It was so easy. I used a screw driver to pop out the old one and pop the new one in. It took 5 min. Thanks!!!
Was this helpful?
Thank you for voting!
Ice maker quit. Got water out of ice dispenser
2 of 2 people found this instruction helpful.
  • Melvin from Girard, IL
  • Really Easy
  • Less than 15 mins
  • Socket set
Wathced video (VERY helpful)of how to do repair to make sure it was within my capabilities to do. Made sure I had all requested numbers before ordering. Replacement part was an EXACT fit. 15 minutes of work and I saved nearly $150 of estimate by local service company. I am (and will continue to be) a repeat customer. Thanks. Mel
Was this helpful?
Thank you for voting!
All Instructions for the 1067698421
121 - 135 of 547