- Home
- 1067697021
- Instructions
1067697021 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bulb Replacement
0 of 2 people
found this instruction helpful.
-
Judith from Phoenix, AZ
- Really Easy
- Less than 15 mins
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this helpful?
Thank you for voting!
non-functioning refrigerator lite switch
0 of 2 people
found this instruction helpful.
-
Ronald from Billings, MT
- Really Easy
- Less than 15 mins
-
Pliers, Wrench set
My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sin ... Read more cerely, Ron Marshall, Billings, MT
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!
Sin ... Read more cerely, Ron Marshall, Billings, MT
Read less
Was this helpful?
Thank you for voting!
light switch would not work
0 of 2 people
found this instruction helpful.
-
Joseph from Destin, FL
- Really Easy
- Less than 15 mins
Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!
Was this helpful?
Thank you for voting!
Water Line To Ice Maker Broke
0 of 2 people
found this instruction helpful.
-
Lennon from Phoenix, AZ
- Easy
- Less than 15 mins
-
Screw drivers
Looked up the process on you yube and watched the repair video from the parts website
Was this helpful?
Thank you for voting!
Noisy defrost timer
0 of 2 people
found this instruction helpful.
-
Jeffrey from Little Falls, NY
- Easy
- Less than 15 mins
-
Nutdriver
Part # had been replaced with another timer. Original timer had 2 wires coming out of it. Replacement only had 1 wire. Instructions showed 2 options for where to place the wire. I chose option 2 and I guess I was right. Installation took less than 15 minutes and refridge is back to normal. (Quiet)
Was this helpful?
Thank you for voting!
The light went out
0 of 2 people
found this instruction helpful.
-
Janet from Flagstaff, AZ
- Easy
- Less than 15 mins
-
Screw drivers
I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.
Was this helpful?
Thank you for voting!
The refridgeror side was not cold enough
0 of 2 people
found this instruction helpful.
-
Patrick from Sun City, AZ
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
it was a simple repair once I located the part I had to replace . I really like your speedy delivery of the part I needed Thank you Pat Crotty
Was this helpful?
Thank you for voting!
Switch was not working after a repairman had fixed something else
0 of 4 people
found this instruction helpful.
-
Jackie from Nova, OH
- Really Easy
- Less than 15 mins
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a
... Read more
single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
Read less
Was this helpful?
Thank you for voting!
Protective cover for bulb had melted
-
Lee from Brooklyn, NY
- Very Difficult
- 15 - 30 mins
-
Screw drivers, Wrench (Adjustable)
I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent i
... Read more
tems in the fridge from being able to touch. Bad solution.
Read less
Was this helpful?
Thank you for voting!
rReally Noisy Fan
-
Robert from Sierra Vista, AZ
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
1. Unplug Refrigerator 2. Remove inside back freezer panel. (4 Screws) 3. Remove Duct Cover (3 Screws). 4. Cut electrical connections to fan. 5. Remove Old Fan motor (2 hex screws. 6. Install ground wire (was not one there previously). 7. Put slide-on electrical connectors on remaining 2 motor wires. (Were not any on original unit.) 8. R
... Read more
eplace Fan Motor (Don't forget the rubber vibration pads) 9. Reconnect electrical wires. 10. Press on plastic fan blade. 11. Plug in refrigerator to test install. It works. 12 Unplug refrigerator and replace ducting and back panel to freezer. Plug it back in. Voila, Quiet again.
Read less
Was this helpful?
Thank you for voting!
Evaporator motor squeal.
-
Steven from Hilliard, OH
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
After finding an almost obsolete part( thanks PartSelect!) the installation was rather easy. Remove the back panel of the freezer and vent with a screwdriver and a nut driver. Disconnect the three wires, green, white and red.Remove motor from mounting and replace with new motor. I had to make a slight adjustment to the ground wire on the
... Read more
new motor that required adjusting the position of the contact-no big deal. The motor fit perfectly. Popped fan on and assembled. 20 minutes max.
Read less
Was this helpful?
Thank you for voting!
Repalce evaporator fan
-
William from Ledyard, CT
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
The evaporator fan is located in the freezer behind the back wall. If you have the ice maker remove it first then remove the screws on the top of the panel. You will notice the side brackets for the top shelf will make it hard to remve the panal but by slitly binding the center the panal came right out. The fan is held in a bracke tha co
... Read more
mes right out. The wire unplu right from the fan so do not try to unplg the seal plug to the left side. Swap the fan with the new one useing the new rubber monts re-connect the wires and reasymble. Put the bottom of the back panal in first then work each side in past the shelf bracket binding the center slightly.
Read less
Was this helpful?
Thank you for voting!
ice maker would not make ice.The fill tube had seperated and iced up so no water could get to ice maker
-
Thomas from newark, DE
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Just followed the video that you guys had on line . It was a very easy repair
Was this helpful?
Thank you for voting!
Both the freezer and bottom of refrig too hot
-
Marcia from Kansas, OK
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Was very simple once I found out where the defrost timer was located. I had a friend walking me through trying to find the location on the phone. Not all models have them in the same place. Once the part was located all I had to do was remove the cover, unplug the old one and plug the new one in just the way the old one came off. The blac
... Read more
k wire was easy to locate on the old and just matched it up. Put the cover back on and plugged it in. It was no time till I started feeling it cool. Checked both top and bottom with thermomater and it was where it should be within 12 hours. I am happy and using it again. Was almost ready to throw it out. Did not know it was so cheap to fix one. Nothing anyone can't handle. If this woman can do it anyone can.
Read less
Was this helpful?
Thank you for voting!
Freezer was too cold and refrigerator was too warm
-
Jolinda from Eau Claire, WI
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
After receiving the part, I watched the installation video on the PartSelect website. The step by step demonstration was excellent. I felt confident I could do it myself after watching the video just once, and utilizing the written instructions that came with the part. The installation went smoothly, and my refrigerator is functioning
... Read more
correctly again. Best of all, I did not have to go through the hassle and expense of hiring a repair person!
Read less
Was this helpful?
Thank you for voting!