- Home
- 1067690821
- Instructions
1067690821 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
frig stopped running and everything ruined
7 of 13 people
found this instruction helpful.
-
allen from Dickson, TN
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
The frig was already empty....removed the plastic control knobs and loosened the hex head screws to remove the cover . The wires were the same at each contact point, so, it took about 15 minuets to adjust the control knob to match the old one and reinstall the thermostat and place the cover...The other 15 minuets I spent finding my wife t
... Read more
o show her the frig was back to work...Just a walk in the park...
Read less
Was this helpful?
Thank you for voting!
the nozzle was broken
4 of 4 people
found this instruction helpful.
-
Alvin from Sugar Land, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
1. PUsh the Lock button so the water will not run.
2.Remove the screw holding the nozzle.
3. Remove the Grill
4. Disconnect the black water tube. Pull the female part of the union off the old tube and hold it for the new tube.
5. PUll it the tube out from the nozzle end.
6. Snake the new tube into the hole and sho ... Read more ve it through until it comes out the door hinge port at the bottom of the door.
7. Continue pushing and pulling the tube until the nozzle is in position.
8.Test fit the new tube and cut a short piece off to fit properly.
9. Slide the female part of the union onto the new tube. Insert it onto the union and tighten.
10. Insert the screw that holds the nozzle in place and tighten.
11. Push the on unlock button and fill a glass with water.
12. Check for leaks. If no leaks reinstall the grill.
Job done.
2.Remove the screw holding the nozzle.
3. Remove the Grill
4. Disconnect the black water tube. Pull the female part of the union off the old tube and hold it for the new tube.
5. PUll it the tube out from the nozzle end.
6. Snake the new tube into the hole and sho ... Read more ve it through until it comes out the door hinge port at the bottom of the door.
7. Continue pushing and pulling the tube until the nozzle is in position.
8.Test fit the new tube and cut a short piece off to fit properly.
9. Slide the female part of the union onto the new tube. Insert it onto the union and tighten.
10. Insert the screw that holds the nozzle in place and tighten.
11. Push the on unlock button and fill a glass with water.
12. Check for leaks. If no leaks reinstall the grill.
Job done.
Read less
Was this helpful?
Thank you for voting!
The water in the door dispenser would run for several seconds and then start clunking. This resulted in no more water flow.
5 of 7 people
found this instruction helpful.
-
Richard from Novi, MI
- Really Easy
- Less than 15 mins
-
Nutdriver
I guessed that the water dispenser solenoid was getting weak.
A quick web search led me to PartSelect's website where it was so easy to pull up my refrigerator model with diagrams. I ordered the valve kit, and in 5 days it was in my hands.
Installation was literally 10 minutes. It took longer than that to vacuum all the du ... Read more st from under and in back of my refrigerator !
A quick web search led me to PartSelect's website where it was so easy to pull up my refrigerator model with diagrams. I ordered the valve kit, and in 5 days it was in my hands.
Installation was literally 10 minutes. It took longer than that to vacuum all the du ... Read more st from under and in back of my refrigerator !
Read less
Was this helpful?
Thank you for voting!
Light in my refrigerator didn't work.
5 of 7 people
found this instruction helpful.
-
Joseph from Byron Center, MI
- Really Easy
- Less than 15 mins
-
Screw drivers
At first I went to a local part supplier and they didn't have it in stock but could order it for me for $55.00 plus $10.00 to ship it. I told them I would have to think about it. I went home and got on the computer and found your web site and was I shocked when I saw the same part listed for $6.98 and $7.00 to ship it. You guys saved m
... Read more
e $50.00. The part arrived in two day and took 5 min. to install. I now have light in my refrigerator. Thank you.
Read less
Was this helpful?
Thank you for voting!
Ice maker was leaking
6 of 10 people
found this instruction helpful.
-
Thomas from San Diego, CA
- Really Easy
- Less than 15 mins
-
Screw drivers
This is an incredibly easy repair.
1) Remove the three screws holding the old icemaker
2) Disconnect the electrical connection (I used a spoon to get in and undo the connector clip
Do the opposite to install the new icemaker.
Total elapsed time was about 5 minutes.
1) Remove the three screws holding the old icemaker
2) Disconnect the electrical connection (I used a spoon to get in and undo the connector clip
Do the opposite to install the new icemaker.
Total elapsed time was about 5 minutes.
Was this helpful?
Thank you for voting!
would shut off and not restart without tapping on knob
4 of 4 people
found this instruction helpful.
-
Brad from RAINIER, OR
- Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
replaced the cold control thermostat . The new one was oriented 90 degrees off (on the bracket mount) so I had to turn it (in the bracket) to line up better with the wire connections and temp sensor tube. The power wires can be connected to either terminal however, and I suppose you could leave it as is if your wires can reach. Turning it
... Read more
will make the knob off 90 deg. off from original markings (off to coldest) but I simply remarked the position with a marker. (make sure you connect all terminals before mounting the bracket, it's much easier that way. .Note: this was a 40+ year old Sears "Coldspot" refridg. and it works like a dream since I changed out this original cold control. Love these old mechanical appliances that are much more reliable than the new brokered ones. Glad whirlpool has made many parts interchangeable through many years...kudos to them
Read less
Was this helpful?
Thank you for voting!
water was leaking under the frig ,wasnt sure what the problem
4 of 4 people
found this instruction helpful.
-
stephen from ROCKLEDGE, PA
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
decided to take a chance and replace the ice maker,so far no water leaking.feels nice to know the problem is fixed.thanks for the video on how to replace it, thanks again very easy repair
Was this helpful?
Thank you for voting!
Refrigerator light would not turn on.
5 of 8 people
found this instruction helpful.
-
Suzanne from STERLING HTS, MI
- Really Easy
- Less than 15 mins
-
Nutdriver
I first replaced the switch and had no results, I then ordered the Light Socket Kit, and because I had the experience of removing the panel to replace the switch, it took a few minutes to remove the two screws behind the panel, removing the temperature control knobs and then releasing the face plate which is secured by tabs at the bottom.
... Read more
The kit came with extra connectors in case they were needed, but they were not in my case and so I pulled off the wires, pushed the old socket out and the new one in. Attaching the wires to the correct pins, I screwed in the light bulb to be sure that the fix was correct and determining that, I replaced the screws that held the panel in place. Voila, I'm a happy camper who found some outdated jars in the back corners of the newly lighted shelves.
Read less
Was this helpful?
Thank you for voting!
Filler tube broken and old tube frozen over
4 of 5 people
found this instruction helpful.
-
Alan from Chino, CA
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers, Screw drivers
this is a snap! 2 screws an a nut to tighten and it works like a charm. the filler tube in my Kenmore refer had broken off in the back. ( really bad location to put this in the beginning) if you push the refer to close to the wall you can break it off easily. remove the water line by loosing the nut and remove the hose from the fill tube
... Read more
( This assumes you have already turned of the water supply or you are standing in a large puddle)remove the 2 screws that hold the filler tube in place. pull out the old filler tube in and slightly upright motion. replace the new fill tube into the same hole and replace the screws. replace the hose and tighten the nut, turn the water back on and check for leaks your done !!
doesn't that feel great?
doesn't that feel great?
Read less
Was this helpful?
Thank you for voting!
Ice maker did not work
4 of 5 people
found this instruction helpful.
-
Judy from Galveston, IN
- Easy
- Less than 15 mins
-
Nutdriver
Took the old one out and plug the new one in, simply as 1 2 3. Order the part one morning,it was here the next afternoon, the ice maker was fixed in less than a half hour. we will order from you the next time.
Was this helpful?
Thank you for voting!
Ice maker not working
6 of 11 people
found this instruction helpful.
-
Raoul from Thousand Oaks, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set
take out Ice maker tray, remove three screws holding the ice maker, unplug electrical connector. Replace with new Ice maker,Ice started to fill the tray. ENJOY!!
THANKS.
THANKS.
Was this helpful?
Thank you for voting!
Broken filler tube at threaded connection
4 of 5 people
found this instruction helpful.
-
Matthew from Phoenix, AZ
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
After discovering that the water noise was coming from the rear of the refridgerator upon pulling it foward I discivered the connection line had broken. So i got a phillips screw driver and removed the the two mounting screws and saw it was one piece. I easliy found the part on PartSelect website and once I got I merely swaped them out
... Read more
and it works good as new!
Read less
Was this helpful?
Thank you for voting!
Dispensed water w/ funny looking particles
10 of 23 people
found this instruction helpful.
-
MARGARITA from TAMPA, FL
- A Bit Difficult
- 1- 2 hours
-
Wrench (Adjustable), Wrench set
First the small screws you sent did not fit.I had to cut and mend the old ones (2) to use them.I did purchase a connecting valve tha I used to connect the part of tubing (my name for it) from old one to new one.I was surprides it is working fine.Not bad for a nurse!
Was this helpful?
Thank you for voting!
Ice Maker didn't produce ice cubes.
4 of 5 people
found this instruction helpful.
-
Michael from Long Valley, NJ
- Easy
- 30 - 60 mins
-
Nutdriver
It was not complicated but it took more squeezing and reaching into the narrow space than actually removing three screws and unplugging the electrical harness. But that was all that was necessary, to install, three screws held the unit in place and re-connect the electrical harness. It saved me about $100 in labor and the inconvenience of
... Read more
scheduling a service call and waiting for a week or so. The best part was that I ordered the unit on line on Tuesday eveining and it was at my home by Friday afternoon with no extra shipping charges. Great service!.
Read less
Was this helpful?
Thank you for voting!
lights wouldn't come on/work in refrigerator
4 of 6 people
found this instruction helpful.
-
Jane from Albuquerque, NM
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers, Socket set
Referencing the info/schematics you have on your website, I unscrewed/unattached top-front panel (carefully), from behind the panel you have to detach the wires (2) from the switch, pushed "in" the switch to remove, put in new switch and attach wires to test BEFORE remounting panel. Tada!! Thank you PartSelect! You saved me at least $80..
... Read more
.would have been at least $100 to have a repair person come to the house!
Read less
Was this helpful?
Thank you for voting!