- Home
- 1067690721
- Instructions
1067690721 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
water dripping in ice cube holder
4 of 6 people
found this instruction helpful.
-
Christine from Clarkston, MI
- Really Easy
- 15 - 30 mins
-
Screw drivers
We removed three screws, unplugged the wire and then removed the old ice maker. Installed the new ice maker with the screws, plugged in the wire and shortly after that we had ice! I was nervous about this repair but it was so easy and the part was here in three days.
Was this helpful?
Thank you for voting!
Would not make ice any longer
4 of 6 people
found this instruction helpful.
-
James from Concord, MA
- Really Easy
- Less than 15 mins
-
Nutdriver
I determined that the ice cube maker was no longer heating the cubes so they could be released into the ice tray. After ordering a new unit, taking out four screws and disconnecting the quick disconnect of wires I plugged the new one in and we were back in business.
Was this helpful?
Thank you for voting!
Raplaced switch
5 of 9 people
found this instruction helpful.
-
Winston A from Brooklyn, NY
- Really Easy
- Less than 15 mins
-
Pliers
Repair went well,took about five to ten minutes to disconnect the power from the fridge removed the defective switch installed the new one ,reconnected the power,,,and Let there be light and there was light!
Was this helpful?
Thank you for voting!
no ice
5 of 9 people
found this instruction helpful.
-
Thomas from Va. Beach, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
directions very well written, easy to follow, no problems
Was this helpful?
Thank you for voting!
Water didn't dispense out of frig door
5 of 10 people
found this instruction helpful.
-
Brian from Golden, CO
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
I purchased the part and put it in,
Was this helpful?
Thank you for voting!
Ice maker was not working.
4 of 7 people
found this instruction helpful.
-
Doyle from Winchester, VA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
On my particular model refrigerator I only needed to remove one screw and disconnet the plug. I then slid the unit out. The new ice maker did not come with the plastic sled that was attached to the old unit. I removed and attached the sled to the new unit with 3 screws.
Was this helpful?
Thank you for voting!
Ice maker wouldn't work
3 of 4 people
found this instruction helpful.
-
Rich from Covina, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Ice maker wouldn't eject the ice often enough. After reading a few other stories, I just ordered the universal ice maker from Part Select. All I had to do was remove some of the plastic shrouds from my old ice maker and put them on the new one. I also reused my mounting brackets. The whole job took me 20 minutes.
Was this helpful?
Thank you for voting!
Icemaker Died
3 of 4 people
found this instruction helpful.
-
Don from Jacksonville, TX
- Easy
- 15 - 30 mins
-
Socket set
The instructions are practically no help, but if you study the diagram, you can figure out the one screw you need to remove. Then the icemaker lift off of two brackets. I couldn't see how to use a screwdriver to unlock the bracket, but just applying mild pressure and pulling it forward brought it right out. I didn't have to change anyt
... Read more
hing with the plug already intalled so it was very easy to pop in, lock the plug, pop into brackets, replace screw and I was in business. 24 hours later I had a bucket of ice! 15 minutes to figure out how to get old out and 5 min to replace new one. Fairly easy. Read posts here to get hints!
Read less
Was this helpful?
Thank you for voting!
Ice maker was leaking and had metal in the ice
3 of 4 people
found this instruction helpful.
-
Charles from Newark, DE
- Easy
- 15 - 30 mins
-
Nutdriver
Removed the screws and disconnected the electric. I put the proper electric harness on and went to fit the unit in but it didn't fit. Until I figured out that you have to use the clips from the old unit that hold the unit in place. The actually hang on them. Once I figured it out it was easy.
Was this helpful?
Thank you for voting!
The water fill tube 90 fitting broke
3 of 4 people
found this instruction helpful.
-
Scott from Crete, IL
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
Removed brokent tube fitting from the compression nut.
Removed two screws holding the fill tube. Removed and replaced the fill tube. Direct replacement, no cutting tube length. Reconnect water line to the new fill tube.......Done.
Removed two screws holding the fill tube. Removed and replaced the fill tube. Direct replacement, no cutting tube length. Reconnect water line to the new fill tube.......Done.
Was this helpful?
Thank you for voting!
heating element going bad
4 of 7 people
found this instruction helpful.
-
James from Bakersfield, CA
- Really Easy
- 15 - 30 mins
-
Nutdriver
I removed three sheet metal screws, unsnapped the electrical pigtail. Then snapped out knock out on new maker. Matched the electrical connection, pushed it in place. Finally set new one in place, leveled it, tightened the scews and walked away.
Was this helpful?
Thank you for voting!
replaced non-functional ice maker
3 of 4 people
found this instruction helpful.
-
Richard from Troy, MI
- Easy
- Less than 15 mins
-
Nutdriver
After first unplugging the refrigerator from it's electrical power source,I removed the lower screw of the ice making unit with a nut driver. I then loosened the upper two screws which hold the retainer clips that secure the unit tight to the freezer wall. I then lifted the unit upward and outward a few inches to allow access to the wire
... Read more
harness. I unplugged the haness from rear of the freezer and removed the unit completely.
To install just reverse the procedure.
To install just reverse the procedure.
Read less
Was this helpful?
Thank you for voting!
Ice maker needed to be replaced as it quit working.
3 of 4 people
found this instruction helpful.
-
Ronald from Henderson, NV
- Really Easy
- Less than 15 mins
-
Screw drivers
Loosened two top screws using a hand held mirror and screwdriver and removed a bottom screw then unplugged the unit inside. Five minutes and repair was complete. Easy as that!
Was this helpful?
Thank you for voting!
Light switch wasn't working.. As I would close the door I would notice our frig light wasn't going off...
3 of 4 people
found this instruction helpful.
-
David from Hemet, CA
- Really Easy
- Less than 15 mins
-
Pliers, Screw drivers
I simply removed the old switch by gently pulling down on the old switch with a screwdriver. When it was about half way out I just gently pulled down on the old switch and it popped out... I removed the two connectors attached to the old switch by pulling on the connectors with a pliers...I tried using my fingers but wasn't able to pull t
... Read more
he connectors off so I used pliers. It worked perfectly.. When pulling off the old connectors, make sure you attach the new switch to the same tabs on the new switch... It was very easy to do and took under 5 mins.....The light switch works perfect....P.S. You should unplug the frig while making the connection just in case....Safety first....!!!
Read less
Was this helpful?
Thank you for voting!
ice tray leaking
9 of 22 people
found this instruction helpful.
-
Linda from Santa Maria, CA
- Really Easy
- Less than 15 mins
Super! It was so fast and easy to fix. Receive my kit in three days and save a lot of money not having to have a repairman come and do it!
Was this helpful?
Thank you for voting!