- Home
- 1067681421
- Instructions
1067681421 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
cooling fan quit
1 of 2 people
found this instruction helpful.
-
George from Belhaven, NC
- Easy
- 30 - 60 mins
-
Nutdriver
Ordered new fan motor on line took out old motor and replaced with new one
Was this helpful?
Thank you for voting!
Condenser Fan Failure
2 of 5 people
found this instruction helpful.
-
Al from Tonka Bay, MN
- Easy
- 30 - 60 mins
-
Socket set
Partition between Freezer and Fridge was running very hot. (Warm is normal). Oiling fan did not work. The only problems encountered in the replacement were getting fan out and in through coolant lines, cut plug off to accomodate generic fan wiring, getting the screws back in without cooking your hand on a hot compressor. Unit works great
... Read more
!
Read less
Was this helpful?
Thank you for voting!
freezer and food section too warm
1 of 2 people
found this instruction helpful.
-
William from Milford, MA
- Easy
- 30 - 60 mins
-
Socket set
removed lower back cover. diconnected fan ass'y electrical connection, removed fan housing (3 screws). removed fan motor from housing. cut old connector from fan and installed on new fan with wire nuts included. re-installed new fan to housing and re-installed housing to frame.
Was this helpful?
Thank you for voting!
door not closing right
1 of 2 people
found this instruction helpful.
-
kenneth from soddy daisy, TN
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
repair was easy. watch the video
Was this helpful?
Thank you for voting!
refregerator would not close by itself
1 of 2 people
found this instruction helpful.
-
Joseph from Scottsdale, AZ
- Really Easy
- 15 - 30 mins
-
Screw drivers, Socket set, Wrench set
Your on line video was fantastic, it led me all the way through the repair. As they say, "A picture or video is worth 1000 words". I wish everyone had instructions like you. Great Job!!!
Was this helpful?
Thank you for voting!
The freezer worked but the refrigerator wouldn't cool.
1 of 2 people
found this instruction helpful.
-
ROBERT from KIRKWOOD, MO
- Easy
- 15 - 30 mins
-
Screw drivers, Socket set
When we got the part, we read the instructions, which were easy and very clear step by step. Taking the old part off took most of the time, it was attached a little differently than was described in the video and the instructions for the part. Once we detached that, the replacement part went in very easily and quickly. It took a short w
... Read more
hile for the cycle to start, we were actually a little worried that it wasn't going to work. Then it started cycling. After the first day the freezer had started icing up, we took a blow dryer and melted it and waited. It hasn't started freezing up again. The refrigerator is keeping the proper temperature and the freezer is also working properly, it's been a week. We seem to be obsessed with going out and checking to see if it's working but I think it's a success. Doing this ourselves only cost $26.00. A huge savings if we had hired someone else to repair it for us. We will definitely choose this option with any other appliance that needs repair. It was easy and simple to find the correct part thanks to the website. And the video tutorial was very informative and helpful.
Read less
Was this helpful?
Thank you for voting!
Freezer door would not shut without a re-enforced push
1 of 2 people
found this instruction helpful.
-
Earl from Sandy, UT
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers, Socket set
I followed your on line video, that was a fantastic help. Easy as 1,2,3. I used the tools he recommended and followed his steps. I replaced the cam on the door and on the bottom pin, its works like new.
Was this helpful?
Thank you for voting!
Light switch broke off
1 of 2 people
found this instruction helpful.
-
Kathy from TEMECULA, CA
- Very Easy
- Less than 15 mins
-
Pliers
We looked up the problem online with the model number of the refrigerator. We ordered the part and followed the video installation that was sent with the order and was found online prior to purchasing
Was this helpful?
Thank you for voting!
refrigerator stopped cooling due to condenser over-heating
1 of 2 people
found this instruction helpful.
-
Kevin from COVINGTON, LA
- Really Easy
- Less than 15 mins
-
Nutdriver, Pliers
Pull refrigerator out to access back, unplug unit and remove the 3 .25" screws cut the power leads to motor and install new with easy to understand instructions provided with new motor. Plug refrigerator back in and enjoy your cold beverages once more. EASIEST REPAIR EVER.
Was this helpful?
Thank you for voting!
light did not work on the refrigerator side
1 of 2 people
found this instruction helpful.
-
David from GROVESPRING, MO
- Easy
- Less than 15 mins
bulbs were not burnt out. received the new switch in a few days. watch the short video, was good to see how it comes out. used a putty knife to release the defective switch, removed wires put them on the new one and posed the new switch back in. Not bad Part cost $11.00 7 dollars shipping so for 17 bucks it works great. nice to see what i
... Read more
s inside the refer!
Read less
Was this helpful?
Thank you for voting!
Rocker on switch broke off
1 of 2 people
found this instruction helpful.
-
David Barnes from ROSWELL, NM
- Very Easy
- Less than 15 mins
Eased the putty knife under the edge of the switch housing and pried it off. Pulled two wires off the old terminals and hooked them onto the new one and reinstalled into the refrigerator body.
Was this helpful?
Thank you for voting!
Motor noise while running and clicking when shutting off
1 of 2 people
found this instruction helpful.
-
Curtis from Sedona, AZ
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
The instruction sheet supplied with the new motor described the steps to take very good. Replaced the rubber grommets for the three motor mounts also. A flashlight or light source was needed or was very helpful.
Was this helpful?
Thank you for voting!
door was not closing
1 of 2 people
found this instruction helpful.
-
Joe from Saint George, UT
- Really Easy
- Less than 15 mins
-
Socket set
Removed all the adjustable shelves inside the door. Removed the top hinge cover (1 nut). then the top hinge bracket (3 nuts). The door doesn't weight very much so you shouldn't have to worry about the door just falling off after you remove the top hinge. then simply lift the door off the bottom hinge and carefully lay it down. One nu
... Read more
t in each of the plastc cams on the bottom of the door and an easy swap out with the new parts. A little vaseline one at least one of the surfaces of the cam, reverse the order and simply put things back together and your good to go. Door closes on its own like new. You might as well get both parts for the lower cam and swap them out simultaniously since you have the door off. PLEAS NOTE: Yes there are two different parts for this repair.
Read less
Was this helpful?
Thank you for voting!
door sounded like it was craking when trying to close
1 of 3 people
found this instruction helpful.
-
Randall from Bradenton, FL
- Really Easy
- Less than 15 mins
-
Wrench set
took all items out of the door, used a wrench to undue the bolts, pulled the door off and placed the new part on the bottom of the door. kept the other new parts that came with the one I needed. very simple
Was this helpful?
Thank you for voting!
The door gasket was very hot which is caused by an overheated expansion line that runs along the area of the door gasket. This was caused by a failed cooling fan motor.
2 of 6 people
found this instruction helpful.
-
James from Howell, MI
- Easy
- 30 - 60 mins
-
Nutdriver
Pulled out the refrigerator and removed the two panels from the rear of the refrigerator. Removed the fan held in by four screws and unplugged the connector. Soldered on the original connector, installed the fan to the motor and re-installed the unit into the refrigerator. Then blew out and vaccumed the condenser coils.
Was this helpful?
Thank you for voting!