- Home
- 1067679621
- Instructions
1067679621 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
fan motor had gone bad
1 of 2 people
found this instruction helpful.
-
william from whitwell, TN
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set, Wrench set
I removed the nuts that held the motor mount, then removed fan blade, cut the wires, and slid the motor pass the mounts and the coil shroud, Installed motor in reverse order. worked out ok.
Was this helpful?
Thank you for voting!
freezer and food section too warm
1 of 2 people
found this instruction helpful.
-
William from Milford, MA
- Easy
- 30 - 60 mins
-
Socket set
removed lower back cover. diconnected fan ass'y electrical connection, removed fan housing (3 screws). removed fan motor from housing. cut old connector from fan and installed on new fan with wire nuts included. re-installed new fan to housing and re-installed housing to frame.
Was this helpful?
Thank you for voting!
cooling fan quit
1 of 2 people
found this instruction helpful.
-
George from Belhaven, NC
- Easy
- 30 - 60 mins
-
Nutdriver
Ordered new fan motor on line took out old motor and replaced with new one
Was this helpful?
Thank you for voting!
The door gasket was very hot which is caused by an overheated expansion line that runs along the area of the door gasket. This was caused by a failed cooling fan motor.
2 of 6 people
found this instruction helpful.
-
James from Howell, MI
- Easy
- 30 - 60 mins
-
Nutdriver
Pulled out the refrigerator and removed the two panels from the rear of the refrigerator. Removed the fan held in by four screws and unplugged the connector. Soldered on the original connector, installed the fan to the motor and re-installed the unit into the refrigerator. Then blew out and vaccumed the condenser coils.
Was this helpful?
Thank you for voting!
Refrigerator would not stay cold
2 of 6 people
found this instruction helpful.
-
Jeremy from State College, PA
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Screw drivers, Wrench set
Removed rear cover to see non-operating fan - removed three mounting screws on the motor that were a challenge to access. Swapped fan from old motor onto new motor - one threaded nut on the motor shaft. Spliced new fan wires into fan wires of the wiring harness and mounted with three self-tapping screws supplied with new fan motor. Repl
... Read more
aced rear cover and plugged it in! Now the refrigerator cools like new (1981 model side-by-side Admiral)
Read less
Was this helpful?
Thank you for voting!
burned oven bulb
3 of 9 people
found this instruction helpful.
-
Ivanka from Atlantra, GA
- Really Easy
- 30 - 60 mins
-
Pliers, Screw drivers
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh
... Read more
t bulb in was not the problem.
Read less
Was this helpful?
Thank you for voting!
Old tube had cracked due to being frozen....
1 of 3 people
found this instruction helpful.
-
Stephen from Greensboro, NC
- Really Easy
- Less than 15 mins
-
Nutdriver
I followed the simple steps outlines in the great video! Thanks
Was this helpful?
Thank you for voting!
thread broke
0 of 1 people
found this instruction helpful.
-
uri from riverhead, NY
- Really Easy
- Less than 15 mins
-
Screw drivers, Wrench (Adjustable)
Unscrew broken piece, pull it out and then insert new one, security it in place and connect water line again, make sure It's thight check for leaks and done
Was this helpful?
Thank you for voting!
Door Light switch cracked Mounting
0 of 1 people
found this instruction helpful.
-
Paul from Hinsdale, IL
- Really Easy
- Less than 15 mins
-
Screw drivers
I noticed that the refrigerator was having trouble maintaining temperature. Thought it might be time for new one until I found out that a new frig was $5k to $7K. Just happened to notice that the light switch didn't look quite right (was not sitting sqaure to the door). Once I pressed it it came loose. I then realized the the lights we
... Read more
re staying on (50 watts of heating). Replaced the switch and the frig started working like new.
Read less
Was this helpful?
Thank you for voting!
The fill tube froze and cracked
0 of 1 people
found this instruction helpful.
-
Phillip from Sellersburg, IN
- Easy
- Less than 15 mins
-
Nutdriver, Wrench (Adjustable)
It was easy and quick to find the part that I needed, order it and have it shipped. The fill tube arived in 3 days and was easy to replace.
Was this helpful?
Thank you for voting!
Part broke.
0 of 1 people
found this instruction helpful.
-
Felix A from Orlando, FL
- Really Easy
- Less than 15 mins
-
Screw drivers
Replacement partfit perfectly.
Was this helpful?
Thank you for voting!
light would work intermitently
0 of 1 people
found this instruction helpful.
-
Gregory from middle island, NY
- Easy
- Less than 15 mins
-
Screw drivers
removed the 2 screws that held the panel in place, had to reach up and push on locking tabs to lower trhe front of the panel. was able to then push on the locking tab of the switch to release it. removed the wires, replaced them onto the new switch, and snapped the switch into place. the rest was reverse of the uninstall process.
Was this helpful?
Thank you for voting!
Filler Tube Broken At Elbow Where Line Hooks Up To
0 of 1 people
found this instruction helpful.
-
LARRY from PARKER, AZ
- Really Easy
- Less than 15 mins
-
Nutdriver, Screw drivers
Replaced fill tube
Was this helpful?
Thank you for voting!
Lights didn't always come on when was opened
0 of 1 people
found this instruction helpful.
-
Gary from Jenkintown, PA
- Really Easy
- Less than 15 mins
-
Screw drivers
Used a screwdriver to pry loose the old switch, swapped wires to the new switch and pushed it into the opening. Took about 2 minutes.
Was this helpful?
Thank you for voting!
19 year old light switch broke
0 of 1 people
found this instruction helpful.
-
Fred from Watertown, NY
- Really Easy
- Less than 15 mins
Great service. Unpluged old switch and pluged in new one. Works great
Was this helpful?
Thank you for voting!