1067643 Kenmore Refrigerator - Instructions

All Instructions for the 1067643
121 - 135 of 178

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Bulb Replacement
0 of 2 people found this instruction helpful.
  • Judith from Phoenix, AZ
  • Really Easy
  • Less than 15 mins
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this helpful?
Thank you for voting!
The refridgeror side was not cold enough
0 of 2 people found this instruction helpful.
  • Patrick from Sun City, AZ
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
it was a simple repair once I located the part I had to replace . I really like your speedy delivery of the part I needed Thank you Pat Crotty
Was this helpful?
Thank you for voting!
non-functioning refrigerator lite switch
0 of 2 people found this instruction helpful.
  • Ronald from Billings, MT
  • Really Easy
  • Less than 15 mins
  • Pliers, Wrench set
My owners manual said to unplug fridge from elec outlet, use a kitchen knife to gently pry off the switch plate
(manual had a pictoral example), unclip the two wire, replace with on new switch and replace the switch. Close
door and plug back in. Open door to check that the lite
works. Walla! It did. Thanks!

Sin cerely, Ron Marshall, Billings, MT
Was this helpful?
Thank you for voting!
light switch would not work
0 of 2 people found this instruction helpful.
  • Joseph from Destin, FL
  • Really Easy
  • Less than 15 mins
Popped the old one out with a kitchen knife and popped the new one back in. It tool less than 15 seconds!!
Was this helpful?
Thank you for voting!
Water Line To Ice Maker Broke
0 of 2 people found this instruction helpful.
  • Lennon from Phoenix, AZ
  • Easy
  • Less than 15 mins
  • Screw drivers
Looked up the process on you yube and watched the repair video from the parts website
Was this helpful?
Thank you for voting!
Noisy defrost timer
0 of 2 people found this instruction helpful.
  • Jeffrey from Little Falls, NY
  • Easy
  • Less than 15 mins
  • Nutdriver
Part # had been replaced with another timer. Original timer had 2 wires coming out of it. Replacement only had 1 wire. Instructions showed 2 options for where to place the wire. I chose option 2 and I guess I was right. Installation took less than 15 minutes and refridge is back to normal. (Quiet)
Was this helpful?
Thank you for voting!
The light went out
0 of 2 people found this instruction helpful.
  • Janet from Flagstaff, AZ
  • Easy
  • Less than 15 mins
  • Screw drivers
I pried the old one out with a screw driver and pushed the new one in. I expected instructions in the box it came in but there were none.
Was this helpful?
Thank you for voting!
Switch was not working after a repairman had fixed something else
0 of 4 people found this instruction helpful.
  • Jackie from Nova, OH
  • Really Easy
  • Less than 15 mins
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
Was this helpful?
Thank you for voting!
Noisy fan
  • Harry from Cincinnati, OH
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Unplug the refrigerator. Remove the rear shelf supports by lifting them straight up. No tools required. Remove the screws holding the rear cover of the freezer. Use a nut driver to remove the 4 screws holding the fan housing. Unplug the wiring harness, then remove the fan and install the new one. Remount the housing, plug in the har ness replace the rear cover, install the shelf supports and plug in the refrigerator. It was 30 minutes start to finish, which includes the time to gather the tools, unload and reload the freezer, and putting the tolls away!
Was this helpful?
Thank you for voting!
Refrigerator not cooling
  • Bryan from Midland, NC
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
Exactly how the part select video described it. Threw a little curve ball figuring out which timer setting to set it to. But the instructions provided with defrost timer walked me right through it. No problem. After installing part nothing happened for about ten minutes, which had me second guessing each and every step. Then, like magic, cold air began blowing. What a relief. Thanks so much, love this site. Refrigerator works like new!
Was this helpful?
Thank you for voting!
Switch didn't work
  • Don from Laramie, WY
  • Easy
  • 15 - 30 mins
followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00
Was this helpful?
Thank you for voting!
How to get timer out of defrost cycle?
  • David from Virginia Beach, VA
  • A Bit Difficult
  • 15 - 30 mins
  • Socket set
Talked to local appliance repair tech, who explained how to manually turn timer with a screw driver and listen to the switch go from on to off.
Was this helpful?
Thank you for voting!
Protective cover for bulb had melted
  • Lee from Brooklyn, NY
  • Very Difficult
  • 15 - 30 mins
  • Screw drivers, Wrench (Adjustable)
I tried to just replace the cover rather than the whole unit but it was impossible - the cover would not go/stay on. I tried to remove the old unit completely but it would not unplug it was practically fused to the back of the fridge and the liner was cracking. I ended up breaking the cover and jerry rigging it over the bulb to prevent i tems in the fridge from being able to touch. Bad solution.
Was this helpful?
Thank you for voting!
rReally Noisy Fan
  • Robert from Sierra Vista, AZ
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
1. Unplug Refrigerator 2. Remove inside back freezer panel. (4 Screws) 3. Remove Duct Cover (3 Screws). 4. Cut electrical connections to fan. 5. Remove Old Fan motor (2 hex screws. 6. Install ground wire (was not one there previously). 7. Put slide-on electrical connectors on remaining 2 motor wires. (Were not any on original unit.) 8. R eplace Fan Motor (Don't forget the rubber vibration pads) 9. Reconnect electrical wires. 10. Press on plastic fan blade. 11. Plug in refrigerator to test install. It works. 12 Unplug refrigerator and replace ducting and back panel to freezer. Plug it back in. Voila, Quiet again.
Was this helpful?
Thank you for voting!
Evaporator motor squeal.
  • Steven from Hilliard, OH
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
After finding an almost obsolete part( thanks PartSelect!) the installation was rather easy. Remove the back panel of the freezer and vent with a screwdriver and a nut driver. Disconnect the three wires, green, white and red.Remove motor from mounting and replace with new motor. I had to make a slight adjustment to the ground wire on the new motor that required adjusting the position of the contact-no big deal. The motor fit perfectly. Popped fan on and assembled. 20 minutes max.
Was this helpful?
Thank you for voting!
All Instructions for the 1067643
121 - 135 of 178