1067600621 Kenmore Refrigerator - Instructions

All Instructions for the 1067600621
121 - 135 of 159

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Intermitant squealing noise from freezer area.
  • Harry from Torrance, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
I basically followed the step-by-step instructions at the parts order website. I removed the shelves and rear panels to access the fan. I noted the color coding on the wires and terminals, removed the two retainer screws, removed the old fan from the mounting bracket, installed the new fan using the rubber anti-vibration mounts, pressed -on the fan to the center drive shaft and re-installed the assembly to the back wall. I simply replaced the rear panels and shelves and plugged in the fridge. The only issue I had was the distance needed to press on the fan blade to preclude fan noise, which I found by trial and error, before re-installing the panels.
Was this helpful?
Thank you for voting!
Water Was Not Reaching The I Ce Maker
  • JOHN from TWINSBURG, OH
  • Easy
  • 15 - 30 mins
  • Pliers, Screw drivers, Wrench (Adjustable)
Disconnect ac power line, disconnect power line going to the water valve. Turn water off atthe cockvalve. Disconnect water line to valve. Disconnect plastic tubing going in the valve. If plastic is old you may have to replace it to keep from leaking at the quick connect coupling. Connect water line and plastic tubling to new valve, connect power clips to new valve. Plug in the refrigertor and turn on water at the cock valve and your good to go
Was this helpful?
Thank you for voting!
How to get timer out of defrost cycle?
  • David from Virginia Beach, VA
  • A Bit Difficult
  • 15 - 30 mins
  • Socket set
Talked to local appliance repair tech, who explained how to manually turn timer with a screw driver and listen to the switch go from on to off.
Was this helpful?
Thank you for voting!
excessive water in condensate pan
  • michael from woodstock, MD
  • Really Easy
  • 15 - 30 mins
  • Pliers, Socket set
just as video instructions said, very easy just following them ,part arrived in very short time and was exact fit completely satisfied, saved repair man service charges and wait time
Was this helpful?
Thank you for voting!
Light bulb failure
  • Grant from Alexandria, VA
  • Really Easy
  • Less than 15 mins
Received the part the day after ordering. Appreciated the quick service and repair took less than a minute.
Was this helpful?
Thank you for voting!
evaporator fan, noisy
  • John from Iselin, NJ
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
Remove freezer shelves, panel, and change fan.
Was this helpful?
Thank you for voting!
Evaporator Would Freeze Up And The Food Section Could'nt Cool
  • michael from buchanan, TN
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
I just followed the enclosed instructions
Was this helpful?
Thank you for voting!
Water was running into refrig from freezer and ice cream was soft
  • William from Delano, MN
  • Really Easy
  • Less than 15 mins
  • Nutdriver
We wasted time looking for the electrical schematic on our refrigerator (the first step in the instructions). By skipping that and reading further in the instructions, the type of cooling that the refrigerator has can easily be determined by the colors of the wires that go to the defrost timer. You need to know this to set up the timer properly for your specific refrigerator. Had I just started there, the entire repair would have taken less than 10 minutes. Very simple repair and it works like a charm, no more water coming into the refrigerator and the ice cream is rock hard. Glad we didn't have to spend lots on a new appliance. Thanks Part Select.com! BH
Was this helpful?
Thank you for voting!
No Light
  • Mary from Jefferson Township, PA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
Took socket out and replace it with new one. Very easy. W saved alot of money doing it ourself.
Was this helpful?
Thank you for voting!
The Refrigerator Was Running But Blowing Hot Air, Everything In Freezer Had Defrosted.
  • Jeanne from Fairview Heights, IL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
First I watched the video on your website, it was quite helpful. It showed me the location of the part to be replaced. Then I used the nut driver to remove a couple of screws, and slowly pulled the cover off . Once I pulled the cover down I could see the part that needed replacing, it had a couple of phillips head screws holding it in place, I removed those screws and unplugged the defrost timer, taking note of the color of the wires. Then I took the new defrost timer and attached the loose wire to the correct terminal according to the directions(this is where the color of your wires comes in), then I plugged in the new defrost timer and replaced the screws. I then reattached the cover making sure not to pinch any of the wires, and replaced the screws. It was so easy I was sure I did something wrong and it wouldn't work, but I plugged the refrigerator back in and let it sit for about 20 minutes and then when I checked it was running cool. I'm 55 years old and never had the nerve to try anything like this before but since my husband passed away I've had to try things myself or replace a lot of appliances. If I can do it anyone can.
Was this helpful?
Thank you for voting!
frosted evaperator
  • Burton from Mount ShaSTA, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I was a Sears repair man for fourty eight years , so I don"t think I should say how easy this was.
Was this helpful?
Thank you for voting!
not makinig ice due to lack of water flow to maker
  • David from Manlius, NY
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Followedinstructions that came with kit. Kit parts were unnecessary as new valve fit in exactly as old one had been. Quick connect for flow out of valve to maker was a surprise as no threaded connection present and no nut necessary; simiply push the line into place. Reconnect water line, check for leaks and refasten back covering. Inst ructions with kit contained an incorrect drawing of connecting water outflowline; a one page addition verbally gave correct info, but detailed step by step instruction for this one connection was confusing. Otherwise, could not have been easier; surely a do-it-yourself project.
Was this helpful?
Thank you for voting!
condenser motor broke
  • patrick from livonia, MI
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
opened box,read directions,took out bad motor,installed new one.PRESTO CHANGO way to go.
Was this helpful?
Thank you for voting!
Refrigerator not shutting off, liquids freezing in fridge
  • Barbara from Apollo, PA
  • A Bit Difficult
  • 1- 2 hours
It wasn't quite as easy to get to the bolts as the video showed. The lay out of the part wasn't exactly like the video either. However, I managed to put the new part in. Unfortunately, it didn't solve the problem. At first the fridge cycled on and off but after 12 hrs it started to freeze liquids again. Since the appliance was 17 years ol d we opted to just get a new one.
Was this helpful?
Thank you for voting!
Fan motor worn out
  • Myrna from Decatur, IL
  • Difficult
  • 1- 2 hours
My Son who is not an appliance repairman did it for me. He had some difficulty getting the nuts and bolts loose mainly. Sorry I'm not much help other than that! I would like to compliment you on your fast service, first time ordering from you and it was for an older model refrigerator that my repairman said he couldn't find. It's working fine now and I'm a satisfied customer!
Was this helpful?
Thank you for voting!
All Instructions for the 1067600621
121 - 135 of 159