- Home
- 1067600521
- Instructions
1067600521 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice maker stop making ice
0 of 1 people
found this instruction helpful.
-
Roy from Blanchard, OK
- Easy
- 15 - 30 mins
-
Wrench set
Looked up the part and found it on PartSelect. I was exactly like the same as the part I had to replace, there for I didn't have to make any new adjustments to the part to fit. I also read the story by others that had the same problem on the website. I had anticipated the part was bad, because no water was getting to the tray. I ordered
... Read more
the part and did the repair pretty quick.
Read less
Was this helpful?
Thank you for voting!
ice maker stopped making ice. i could tell it wasn't getting any water, which appeared to be a problem with the water valve.
1 of 4 people
found this instruction helpful.
-
Jerry from Olympia, WA
- Easy
- 30 - 60 mins
-
Screw drivers, Wrench set
Fridge has a top freezer. I unplugged the fridge and removed the lower panel in the back. I removed the two screws that hold the valve bracket to frame of fridge in lower right corner (facing fridge from back). I then disconnected the modular wiring plug and both the water supply and the hose to the icemaker.
i connected the power pl ... Read more ug to the new part, reconneced the hose to the icemaker and reattached the bracket with the two screws into the frame of the fridge. finally, i reconnected the water supply and plugged in the fridge. In a few hours the icemaker was working like new. I figure i save about $100 or more by not having to call a repairman and it was easier than I had expected.
i connected the power pl ... Read more ug to the new part, reconneced the hose to the icemaker and reattached the bracket with the two screws into the frame of the fridge. finally, i reconnected the water supply and plugged in the fridge. In a few hours the icemaker was working like new. I figure i save about $100 or more by not having to call a repairman and it was easier than I had expected.
Read less
Was this helpful?
Thank you for voting!
Ice Maker quit workin
0 of 1 people
found this instruction helpful.
-
Charles from Orange Park, FL
- Really Easy
- 15 - 30 mins
-
Pliers, Socket set
Turned off water supply and electricity. Removed old valve by removing two 1/4 in nut screws and water supply line and the ice maker suppy line. Disconnected the electrical line.Reattached water supply line,the icemaker supply line and the electrical connector. Put valve back into refrigerator and attached the two 1/4 in nut screw. T
... Read more
urned on water supply and electricity. Bled water thru system and now have plenty of ice.
Read less
Was this helpful?
Thank you for voting!
The refridgeror side was not cold enough
0 of 2 people
found this instruction helpful.
-
Patrick from Sun City, AZ
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
it was a simple repair once I located the part I had to replace . I really like your speedy delivery of the part I needed Thank you Pat Crotty
Was this helpful?
Thank you for voting!
Bulb Replacement
0 of 2 people
found this instruction helpful.
-
Judith from Phoenix, AZ
- Really Easy
- Less than 15 mins
I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.
Was this helpful?
Thank you for voting!
Noisy defrost timer
0 of 2 people
found this instruction helpful.
-
Jeffrey from Little Falls, NY
- Easy
- Less than 15 mins
-
Nutdriver
Part # had been replaced with another timer. Original timer had 2 wires coming out of it. Replacement only had 1 wire. Instructions showed 2 options for where to place the wire. I chose option 2 and I guess I was right. Installation took less than 15 minutes and refridge is back to normal. (Quiet)
Was this helpful?
Thank you for voting!
noisey fan
0 of 4 people
found this instruction helpful.
-
Richard from Morgan, UT
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
yup
Was this helpful?
Thank you for voting!
See below
-
Patricia from Hobe Sound, FL
- Really Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
The defrost timer that I ordered form you did the trick. My fridge was
running all the time and the fridge temp was 55 but the freezer was 10
below. The instructions did not say how to test the old one to compare with
the new on. However in the Readers Digest Home Repair book it did and the
test proved that it was defe ... Read more ctive. Your article said that with the system I
had, 65% on the time it was the timer. I ordered it and thank you it works
just fine. I do have another problem, maybe you can help. The fridge runs
for 6 minuets and stays off for 10 minuets. The temp in the freezer is 0
and the fridge is 35-40 on the warmest settings, but all is well.
Thank you
running all the time and the fridge temp was 55 but the freezer was 10
below. The instructions did not say how to test the old one to compare with
the new on. However in the Readers Digest Home Repair book it did and the
test proved that it was defe ... Read more ctive. Your article said that with the system I
had, 65% on the time it was the timer. I ordered it and thank you it works
just fine. I do have another problem, maybe you can help. The fridge runs
for 6 minuets and stays off for 10 minuets. The temp in the freezer is 0
and the fridge is 35-40 on the warmest settings, but all is well.
Thank you
Read less
Was this helpful?
Thank you for voting!
Freezer was not getting cold enough
-
David from Salem, WI
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers
Mine was alittle different than the online instructions. 1. I removed the motor. 2. I took the fan off the old motor and cut the wires about 3" back from old motor. 3. Mounted the new fan on bracket and put the fan on the new motor. 4.connected wires that were cut and used wire nuts to connect. 5. Mounted bracket and motor/fan to unit and
... Read more
it works like its brand new. Thank you PartSelect!
Read less
Was this helpful?
Thank you for voting!
Condensor Fan going bad
-
George from Hickory, NC
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
I knew the repair wasn't difficult. It was a matter of finding the replacement part. Luckily, I found the part via the internet on your site. Lucky for me, there was an installation video!! These videos are worth 1000 bucks!! Never have encountered a site with installation videos before. It gave me complete insight as to how the job was
... Read more
sequenced. I'm a very visual person, so videos are the perfect helper for me. With fewer and fewer affordable local service companies around to fix problems like mine, your site gave me the complete confidence to easily switch out the condensor fan. I completed the repair for about $63.00. Your site ROCKS! Keep up the repair videos because they are awesome and extremely helpful. I felt like your pricing was competitive for this item. Thanks again!!
Read less
Was this helpful?
Thank you for voting!
Both the freezer and bottom of refrig too hot
-
Marcia from Kansas, OK
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Was very simple once I found out where the defrost timer was located. I had a friend walking me through trying to find the location on the phone. Not all models have them in the same place. Once the part was located all I had to do was remove the cover, unplug the old one and plug the new one in just the way the old one came off. The blac
... Read more
k wire was easy to locate on the old and just matched it up. Put the cover back on and plugged it in. It was no time till I started feeling it cool. Checked both top and bottom with thermomater and it was where it should be within 12 hours. I am happy and using it again. Was almost ready to throw it out. Did not know it was so cheap to fix one. Nothing anyone can't handle. If this woman can do it anyone can.
Read less
Was this helpful?
Thank you for voting!
How to get timer out of defrost cycle?
-
David from Virginia Beach, VA
- A Bit Difficult
- 15 - 30 mins
-
Socket set
Talked to local appliance repair tech, who explained how to manually turn timer with a screw driver and listen to the switch go from on to off.
Was this helpful?
Thank you for voting!
Condensor fan motor quit working
-
David from New Albany, IN
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Pulled the fridge out, Took bottom panel off. Removed 3 screws holding motor. Unplugged connector, cut wires, attached old connector on new motor. put blade on new motor.installed in fridge, put cover back on.
Was this helpful?
Thank you for voting!
Condensor motor was frozen
-
john from thibodaux, LA
- Really Easy
- 15 - 30 mins
-
Nutdriver, Pliers
pull unit away from the wall, and unplug it. remove the grill, and cardboard guard on the lower back of the unit. remove Three screws for the motor bracket. Remove the bracket legs from the old motor and assemble them to the new motor. take the fan blade off the old motor, place it on the new. Cut the wires at the old motor, strip th
... Read more
e insulation back, use supplied wire nuts to connect the new motor. Reverse order to reassemble. Plug in unit to test function.
Read less
Was this helpful?
Thank you for voting!
condenser motor broke
-
patrick from livonia, MI
- Easy
- 15 - 30 mins
-
Nutdriver, Pliers, Screw drivers
opened box,read directions,took out bad motor,installed new one.PRESTO CHANGO way to go.
Was this helpful?
Thank you for voting!