106726501 Kenmore Freezer - Instructions

Replaced refrigerator cooling control. No luck. Replaced freezer cooling control. No luck. Coils were icing up. Unplugged frig and allowed coils to defrost. After more poking around, found that condenser fan was not spinning. Touch it and it'd start. That was definitely in need of replacement. Replacement was easy. Refrigerator is now running as it should.

Removed the old timer from the housing. The replacement came with good instructions. I followed the instructions corresponding to the color wires in my unit. The first time it was installed, the fridge did not come on and the temperature rose after a couple hours. Looked at the part and realized the defrost cycle must have kicked in. Needed to slightly turn the gray slotted part to initiate the timer so it would stop the defrost and start the fridge. That did it! It must have advanced the timer so it could accumulate run time. Whole repair saved us $3000 in a new fridge.

First defrosted it to makes sure all Air flow was opened. Tested the Defroster heater with omh meter, it was OK. Found the location of the defrost timer on the online diagrams. Used nut driver to remove cover.
Replaced timer. The hardest part was decieding how to wire it up, tis was a universal kit and depending on how it was wired as to how often the defrost ran. The firt choice was every 8 hours. Since this was going to be opened often, I picked that one.
Plugged it with in 24 hrs freezer wall mesured -5 and the fridge was at 30, so had to warm it up a bit.
Now all complaints gone, Ice making has been doing better also.

Second time in about two months, and it's never done it before in the 19+years we've had it.
Several good YouTube videos on replacing the "Heat Probe", though generally for newer models. You can probably figure it out, though.
Unplug the 'fridge
1. empty the freezer
2. take out the shelf and ice maker (three screws w/ 1/4" nut driver)
3. remove the "floor" of the freezer (two screws w/ 1/4" nut driver)
4. remove the back of the freezer (two screws w/ 1/4" nut drive)
You will see ice buildup in the drip tray and in the drain hole. That's the problem.
This is probably a ton of ice under the freezer floor. I used a thin metal spatula to pry up the sheets of ice, up to the metal drip tray.
I used a heat gun (a hair dryer would probably work) to thaw the ice around the drip try and pry it out. Don't over heat anything. Take your time. Don't melt anything other than the ice and do that slowly.
Be VERY careful around the fins and refrigeration tubes.
It took about an hour to get all the ice out except for the iced up drain hole.
Boiled some water and carefully poured it on the ice in the hole. Blot out the melted ice with a sponge or paper towel. Do this over and over until the ice is about a half inch below the lip, still plugging hole.
Use a turkey baster or a funnel with a piece of hose and keep pouring hot water into the drain hole. The baster is good because you can not only add the water, you can suck out the melt water.
Keep doing this until you start hearing water draining into the drip tray underneath the 'fridge. The drain hole is now clear.
Wrap the heat probe around the black tube under the refrigeration coils and fins and insert the tab into the hole.
Crimp the heat probe tightly around the black tube and attach it tightly with the screw.
NOTE: My refrigerated did not come of a heat probe originally and the kit did NOT come with an attachment screw, so I had to improvise. If you are replacing you probe, save the screw.
Reassemble the freezer in reverse order of disassembly. Hooking the ice maker back up is a royal PITA. And make sure you attach the little grounding wire to the tab on the back panel before you attach the panel.
Plug the refrigerator back in. The ice maker won't work until the freezer is cold enough to make ice again. That will take several hours.

Unclogging the drain was not the main problem. The cause was the problem. Back panel in back of freezer was rusting over the years, and rust and pieces of paint were clogging the drain. Would have had continuing problem. Sanded all the rusted areas on back of panel, and then covered them with strips of duct tape, and reassembled. rust wont break loose and clog the drain. That is the permanent fix! Tape prevents droppings that clogged drain. Pieces of rust and paint clogging drain was the cause, nothing more. Checked tape, and it's doing it's job, and holding tightly, even with freezing and moisture. Fixed for another 19 years. Part was not necessary so far. Rust over the years was the problem. Sorry, but this doesn't sell parts, does it?

Order the part from the Internet on Sunday, it mailed out on Monday and I received it on Tuesday. I unplugged the fan then undone 3 screws that held the fan bracket to the refrigerator pulled it out unscrewed 3 more nuts and replaced the fan on the bracket and I cut the old wire plug off the old fan and with 2 wire nuts put it on my new fan. Replaced the fan and bracket back on the refrigerator plugged it in and it works like a new refrigerator.

removed back cover, removed fan motor and replaced with new one. connected new power wires. worked right away

I replaced the defrost relay folling instructions I read on the internet--and it still didn't work--So I replaced the compressor start relay which was easier than the defrost relay--it worked and the fridg is working good.

Pop off six mounting screws and the ground screw. Remove the fan blade and reattach. Reinstall. Save yourself big bucks.

The parts were reasonably priced, shipped promptly and received in a couple of days. I reviewed a YouTube video before starting that was beneficial. Huge savings over retail repair service. A+ replacement parts house and I would highly recommend.

It's self-explanatory. The procedure is obvious; it's just a little difficult. The only hard part is attaching the mounting brackets to the fan. If you can't tighten the mounting bolts, loosen them and reposition the brackets. You might end up mispositioning them at first, because they are hard to reach.

After the front panel was removed, disconnected the timer and installed new in reverse order. The provided instructions could be more straight forward, I spent more time reading it than the installation itself.

First I removed all the screws from the back cover.
2nd removed fan nut and fan blade
3rd removed fan bracket
4th I traced wire to the condenser and disconnected wires from wire nuts.
Installed existing fan brackets to new motor kit
then reconnected wire nuts to new motor cord
Reinstalled fan nut and blade,
reinstalled cover, plugged it in and BAM .WORKS PERF!

The repair was easy, I removed the cover on the top front of the fresh food compartment. It housed the defrost timer which was easy to identify and replace. Just removed a screw, unplugged the wires and replaced with the new part. Unfortunately, that wasn't the only problem. I also had to replace the defrost element that the timer sent power to. While I was at it, I replaced the defroster thermostat. The entire repair took under an hour, diagnosing the problem took the most time and effort.

I got the product very quickly. (thank you) Looked at online instructions that were quite vague. Pulled plug.Removed the holder for the fan motor slid it out to see what I had. Removed the mounting screws (3) and slid the motor an fan blade out. I made a cut between the wires and marked the "top" wire to motor to be sure to spin in right direction. Removing fan blade hold down clamp was NOT explained at all but I noted that the shaft on the motor was threaded, so I used pliars and held the shaft white un-screwing clamp. I cleaned the fan blades with degreaser and scraped edges of opening on holder opening. Make sure to use ALL the NEW parts included with this kit when re-installing. They send them for a reason. When slpicing and connecting wires it is a 50/50 shot if you don't mark before cutting. You can connect and try plugging fridge back for moment and make sure it is blowing OUT. Put everything back together and after turning DOWN the thermostats twice, fridge is back to usual. Ice maker is cranking out ice and outside case is cool to the touch.

Note: This can be a DIRTY job especially with 4 dogs in house. Fir and grease don't mix well