10670528901 Kenmore Refrigerator - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
No ice, water to dispenser OK
Originally replaced water inlet valve, not the problem. Tried to work from cheap to expensive.
1. Turn off power, shut off water supply
2. Loosen top two screws of ice maker (will slide up and off, no need to take top two out)
3.Remove bottom screw from ice maker
4.Pulled unit, snapped out existing wire harness
5.Cut hole for water inlet on end of new unit and attached wire icemaking on/off bracket.
6 Connected existing wiring harness to new unit
7. Slid new unit down onto top two screws, put in bottom screw and tightened all three
8. Turned on power and water supply
Had ice being made within two hours. Part Select has given me great service, highly recommend.
1. Turn off power, shut off water supply
2. Loosen top two screws of ice maker (will slide up and off, no need to take top two out)
3.Remove bottom screw from ice maker
4.Pulled unit, snapped out existing wire harness
5.Cut hole for water inlet on end of new unit and attached wire icemaking on/off bracket.
6 Connected existing wiring harness to new unit
7. Slid new unit down onto top two screws, put in bottom screw and tightened all three
8. Turned on power and water supply
Had ice being made within two hours. Part Select has given me great service, highly recommend.
Parts Used:
-
Mike from Myrtle Beach, SC
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Socket set
44 of 50 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The freezer section was working fine. Not properly cooling the refrigerator
I looked on line to see what was causes of the problem and determined that it was probably the fan in the freezer not working. I took the back section of the freezer apart and saw the fan was not running. I checked the parts on line and found that it was availiable and ordered a new fan motor. The blade looked fine, but I ordered a grommet anyway to ensure that there was no vibration problems causing the fan motor to go out. When the fan motor arrived, I began disconnecting the old one after unpluging the refridgerator and noting the terminals for the wires. The wire terminals were in a slightly different location, but reasoned out which wire belonged to the correct location. I pulled the old fan motor out, switched out the fan blade and grommet and re-incerted the new fan motor. I reconnected the wires and re-assembled the rear wall of the freezer. I plugged in the refridgerator and wa-la! It worked.
Parts Used:
-
Donald from Waco, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
44 of 51 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
ice maker did not make ice
The ice maker was not getting water. I hotwired the water valve by switching the connectors for the water dispenser and ice maker water valves and water flowed into the icemaker when the water dispenser lever was pushed. I wronly assumed the water valve was good. I removed the icemaker and determined that the gear motor was not getting power in the position the icemaker had stopped.In this position, the thermostat determines when the motor gets power so I replaced the thermostat. The icemaker still would not get water! As it turns out, the water solenoid was sticking due to a deteriorated rubber washer which let the solenoid plunger get too far out of the magnetic field. I replaced the water solenoid assy and all is well. Don't get fooled by hotwiring the valve. If it isn't getting water, the solenoid probably is the culprit.
Parts Used:
-
DAVID from TINLEY PARK, IL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
47 of 61 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice Maker stopped working due to defective timing gear
I removed two screws on the top and one underneath the unit. Then I disconnected the cable. The hardest part was getting the nut driver on the bottom screw because it was obscured by the unit. The replacement unit plugged right in! I got my first batch of ice in about 20 minutes. All I really needed was the timer unit, but the entire ice maker wasn't much more expensive, especially when you consider the time saved on installation!
Parts Used:
-
Nicholas from Boca Raton, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
42 of 46 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Leaking tray created iceberg but few ice cubes!
Received my kit quickly. Job was fast and easy. Removed 3 screws with nutdriver and unpluged the wiring harness. Use a flat blade screwdriver to lift the tab on the plastic end cap of the harness. The icemaker comes out in one piece. The wiring harness that came installed on the replacement icemaker matched mine perfectly. (It comes with two others). I plugged the new one in, replaced the screws, bottom one first to help hold it while replacing the top two screws. I used the shut-off arm from my faulty icemaker. Turned the power back on and put 1/2 cup of water in the tray and walked away. Ice dropping into the bin was music to my ears. Didn't need any of the clips or things that came with the icemaker. It was basically a "plug and play". I'm so happy to have ice again, and at a great savings!
Parts Used:
-
Brenda from Palm City, FL
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
54 of 83 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice Maker Stopped Making Ice
I had a technician called out to the house to look at repairing several appliances that all have broken parts after just 3 yrs of use. Hood, Microwave, Oven, Fridge all in need of minor repairs..
Anyway - the estimate was $240 to replace the ice maker. I ordered PS358591 for $104. and it came in a couple days.. I took out one screw - slid out the icemaker, unplugged it - plugged in new one and slid it in the slot - and done !! Took about 20 mins.. didnt need any of the wiring harnesses in the box from partselect. Was way to easy to do !!
Thank you !
Anyway - the estimate was $240 to replace the ice maker. I ordered PS358591 for $104. and it came in a couple days.. I took out one screw - slid out the icemaker, unplugged it - plugged in new one and slid it in the slot - and done !! Took about 20 mins.. didnt need any of the wiring harnesses in the box from partselect. Was way to easy to do !!
Thank you !
Parts Used:
-
robert from kennesaw, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Socket set
43 of 51 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Icemaker would not stop putting out water, then would not make ice
First, I unplugged the power to the entire fridge, and then removed the ice tray and ice door. Next, I unplugged the flat plug in the very back left behind the icemaker. Then I removed the 1/4" hex head sheet metal screws (2) and the phillips head screw (1) that hold the icemaker to the left side of the freezer wall. New icemaker came with a different style trip arm, so I used it. Plugged new icemaker in before reattaching it with the same (3) screws. Replaced ice tray and door, plugged in fridge, and waited....Dumped its first batch of ice maybe a couple of hours later. Not much trouble-shooting is needed when the entire icemaker is as easy and relatively inexpensive to replace as this. Twenty minutes, max.
Parts Used:
-
Phil from Felton, DE
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
44 of 56 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Light Switch broke
An easy job for smaller hands. Removed the two bolts holding the light cover. Removed two electrical connections from the old switch by pinching the retaining clip,removed the switch, snapped in the new one and re-attached the connectors. Your online illustrations helped me to know that the plastic housing for the light switch would only swing down so far and was not intended to be removed. Saved me from breaking that plastic cover's tabs. This home repair saved me more than 5 times the cost of hiring a professional to do it. Very happy homeowner.
Parts Used:
-
James Richard from St. Cloud, MN
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Socket set
44 of 60 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Timer "clicking", indicating worn gears
1. Unplug refrigerator to remove power!
2. The timer is inside the control housing located at the top of the refrigerator compartment.
3. Remove two control knobs (the pull off).
4. Remove the front panel escutcheon. The panel is not held in place with screws, but can be gently pried off.
5. Remove two screws from the back that hold the housing in place.
6. Remove screws from the front that hold the housing in place.
7. Drop housing down (still attached by wires - do not detach). Timer is inside housing, located on right.
8. Follow the instructions provided to identify your particular wiring setup. You'll find the wiring diagram (on my model) at the bottom of the refrigerator, alongside the defrost catch pan, behind the airflow grille.
9. Remove connector from timer terminals (4).
10. Remove two screws/nuts that hold the timer in place.
11. Install replacement timer following included directions. Read and follow ALL instructions applicable to your particular model and wiring setup.
12. Reassemble by reversing the steps above.
13. Note: You may need to "jog" the replacement timer when you first plug the refrigerator back in, if the timer happens to be in a "defrost cycle" (the compressor won't start). This can be done by inserting a wide bladed screwdriver into the hole below the timer, aligning it with the timer shaft, and slightly turning the shaft CW. Don't force it, and don't turn it very far.
2. The timer is inside the control housing located at the top of the refrigerator compartment.
3. Remove two control knobs (the pull off).
4. Remove the front panel escutcheon. The panel is not held in place with screws, but can be gently pried off.
5. Remove two screws from the back that hold the housing in place.
6. Remove screws from the front that hold the housing in place.
7. Drop housing down (still attached by wires - do not detach). Timer is inside housing, located on right.
8. Follow the instructions provided to identify your particular wiring setup. You'll find the wiring diagram (on my model) at the bottom of the refrigerator, alongside the defrost catch pan, behind the airflow grille.
9. Remove connector from timer terminals (4).
10. Remove two screws/nuts that hold the timer in place.
11. Install replacement timer following included directions. Read and follow ALL instructions applicable to your particular model and wiring setup.
12. Reassemble by reversing the steps above.
13. Note: You may need to "jog" the replacement timer when you first plug the refrigerator back in, if the timer happens to be in a "defrost cycle" (the compressor won't start). This can be done by inserting a wide bladed screwdriver into the hole below the timer, aligning it with the timer shaft, and slightly turning the shaft CW. Don't force it, and don't turn it very far.
Parts Used:
-
John from Plano, TX
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
37 of 42 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Scratches in Surface
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
Parts Used:
-
Michelle from Richardson, TX
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
65 of 128 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Refrigerator Wasn't Cooling,Evaporater Coil Freezing Up
I have a side by side so in order to access the bi-metal switch I first had to empty out the freezer. The switch is clipped on to the top of the evaporator coil. I had to remove 8 screws to remove the back panel of the freezer compartment. The bi-metal switch was right there in plain view. There are two colored wires that come out of the switch. I tried pulling them out of the socket they were plugged into but gave up for fear of breaking something. I ended up cutting the wires and splicing them together. I used the plastic twist caps. I made sure when I closed everything back up that the open end of the caps were pointing down so no water can accumulate in them. It has been 3 days now and so far so good
Parts Used:
-
Robert from Doral, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
38 of 50 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Auto Defrost Freezer keeps defrosting SIDE BY SIDE KITCHENAID
DISCONNECT POWER. Removed all shelves/baskets.Popped upper panel off (just clips in) Removed 6 screws in lower back panel ( 3 each side) slid panel in place but down. You can then easily see the defrost thermostat/defrost termination switch. Cut the wire connectors (pink n brown wire) stripped back wire, attached new defrost thermostat. Thermostat clips on. New thermostat ohm's at 5.5, old one was "open". Slid cover back up meeting the upper cover grooves. Screwed lower panel in. Put shelves etc back in. Plugged in. Turns on, put a bottle of water in freezer. Checked a while later, frozen. has been frozen for a week.
-James
-James
Parts Used:
-
James from Ringoes, NJ
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Screw drivers
37 of 47 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freezer wasen't cooling refrigerator
Removed the old defrost heater screws and connected the new one. I have 46 apartment units here and have had about 15 defrost heater's replaced by service repair person at a very expensive cost. To my surprise it was extremly easy and a lot less in cost.
Parts Used:
-
Joann from ATCHISON, KS
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
34 of 43 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The black plastic or teflon coating on the ice mold was coming off in flakes and freezing in the ice cubes
I took out the ice collection box and auger to get access to the three screws holding the ice maker assembly against the left wall of the freezer. You can use a screwdriver or a nut driver. I then unpluged the assembly and wiggled it loose from the water fill tube. I assumed that unplugging the unit would disable the water valve but I put a plastic tub under the fill tube just in case. I studied the assembly on the kitchen table for a few minutes before I disasembled it. After removing a snapon plastick cover I removed three or four screws on the gearbox and was able to pull and wiggle the parts apart. The heater contacts have rubber O rings so you have to be firm pulling the mould out of and into the gearbox mount. Make sure it is fully seated. On reassembly note that the ice kicking arm is notched so it fits into the gearbox only one way and it helps to have it in position when you screw the gearbox back on. I also found the plastic ice guide that fits on top of the mold a little awkward in snaping back together. Make sure its fingers space evenly with the ice kicking arms.
Parts Used:
-
Roger from Sunnyvale, CA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers
32 of 42 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Ice maker mold was cracked and leaking water into the bin which then froze all the cubes together.
I removed the ice maker assembly from the freezer compartment (four nuts/ nut driver) and unplugged the wire harness. I discovered the nature of the problem and I went on the Internet to look for replacement parts expecting I'd have to buy the entire ice maker. When I found PartSelect.com I looked through the pictures of the parts available for my ice maker. I found the correct part quickly and easily. And having an acurate photo on the site, I was able to match all the key features of the mold I had with the one on the screen. I ordered the part, and installed it the day it arrived with just a Phillips screwdriver and a nut driver. It functions perfectly.
Parts Used:
-
George from Cottage Grove, MN
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
28 of 30 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!