1067021 Kenmore - Instructions

inserted a knife between the switch and the plastic interior in order to pop the switch out.
then took off the 2 wires on the old switch put them on the new switch and reinserted the switch into the plastic interior.

I took out the old socket by moving a clip. Reattached the electrical wires, clicked in the socket and that was it.

It was exactly as everyone else described--remove old ice maker, unplug, plug in new ice maker, attach new ice maker. 3 screws, 1 plug. My plug was the one on the ice maker not on the refrigerator (ie I used the wiring/plug that was already in the freezer).

On my particular model refrigerator I only needed to remove one screw and disconnet the plug. I then slid the unit out. The new ice maker did not come with the plastic sled that was attached to the old unit. I removed and attached the sled to the new unit with 3 screws.

Ice maker wouldn't eject the ice often enough. After reading a few other stories, I just ordered the universal ice maker from Part Select. All I had to do was remove some of the plastic shrouds from my old ice maker and put them on the new one. I also reused my mounting brackets. The whole job took me 20 minutes.

removed three screws pluged it in and it was ready to go. I must add That I ordered it one day and received it the next day by fed ex. I could not believ how fast the service was also the new icemaker is working great. I will order any furture parts I need from Parts Select. Also have given your web site ot several other people. Thank you ... Read more very much.

i noticed that no water was getting to the ice maker. rather than messing around with parts, i bought the entire unit. easy to remove old one and install new one. thanks...ice started again in about an hour. unit cost less than a service call!

Followed instructions on your website

I took a chance and ordered a switch that is next to the top of the door. looked for how to remove it easily done in ten minutes works fine last long time.

I removed three sheet metal screws, unsnapped the electrical pigtail. Then snapped out knock out on new maker. Matched the electrical connection, pushed it in place. Finally set new one in place, leveled it, tightened the scews and walked away.

Removed the screws and disconnected the electric. I put the proper electric harness on and went to fit the unit in but it didn't fit. Until I figured out that you have to use the clips from the old unit that hold the unit in place. The actually hang on them. Once I figured it out it was easy.

The instructions are practically no help, but if you study the diagram, you can figure out the one screw you need to remove. Then the icemaker lift off of two brackets. I couldn't see how to use a screwdriver to unlock the bracket, but just applying mild pressure and pulling it forward brought it right out. I didn't have to change anyt ... Read more hing with the plug already intalled so it was very easy to pop in, lock the plug, pop into brackets, replace screw and I was in business. 24 hours later I had a bucket of ice! 15 minutes to figure out how to get old out and 5 min to replace new one. Fairly easy. Read posts here to get hints!

First I had to figure out how to get the old unit out so I could work on it. The three screws that others wrote about were the ones that hold the motor in place. There are 3 screws holding the ice maker in the frame, along with one screw covering the electrical connection. The electrical connection was difficult to unplug because the l ... Read more ocking tab was on the back side of the connection and with no room to work in the freezer it didn't become apparent until several frustrating minutes went by. There were no instructions provided, the picture on the ordering page showed the complete ice maker, and for $80 you get a printed circuit board with a small round item which must be the motor/timer control. The two plastic parts for moving the ice from the ice maker were included but not replaced because I didn't notice them until I had finished replacing the ice maker back in the freezer and wasn't going to start over again.
Once installed, there wasn't any noise, even of water flowing like the old one, could not tell if the unit was working or not. In the morning there was new ice in the bin indicating the repair had been successful. This is like anything else, if you have done it before it is a 5 minuter job but when you have to look at it and try to figure it out it takes a bit longer. All in all, it was simple enough, I was expecting a complete ice maker unit like was in the picture when ordered but only the motor module was actually needed.
We have another refrigerator/freezer that has an icemaker that is over 20 years old and has never been repaired, it is a Sears model though, probably made by Whirlpool or someone else.

The gasket has an inner lip that fits over the edge of the door plastic liner. The old gasket was removed by pulling it straight out, in the plane of the door. Try not to pull sideways as it could crack the door liner, which gets brittle with age. The new liner had a brown magnetic strip, which holds the door closed, and this fits behi ... Read more nd the edge of the door liner. Start on the bottom of the door. A helper is useful to hold the gasket loosely vertical. A flat blade screwdriver can be used to pry away the liner to insert the new seal. Once you have worked in the lower edge, install both sides, and then the top. Some juggling side-to-side may be needed for an exact fit

took door of the refergarator. Then cut old gusket of and clipped the new one on and then put the back. Done!!!!!