10669312310 Kenmore Refrigerator - Instructions

Remove light lens by pushing straight back (needs some oomph, but not too much). Remove control housing by prying spring clips in back of housing with thin screwdriver or knife. Remove old control board by releasing plastic clips on both sections and removing 2 wiring plugs. Be careful snapping new control board in ; the alignment of the 4 switches and the 2 readouts is critical - easy to hang up a switch. Snap the control housing back into place, making sure that it is all the way in. Position the light lens so that it is lined up and about 1/2" back and then slide it forward (toward you) into place. The instruction sheet calls the refrigerator section the "fresh food" section. There are 2 light switches, one for each door. Both have to held down to get light to go out and enter programming mode. Easiest to close the right door, then push left door switch and quickly push the freezer DOWN button 3 times. Follow the instructions to set the program on the display and then push AND HOLD the freezer DOWN button until the display starts flashing. Release the freezer DOWN button, close the doors, open the doors to check. Display will indicate two 4s. (that was what mine indicated). Done.

I did it exactly how the video that was shown when I purchased the new rail. Following those instructions worked perfectly.

Viewed the viedo - it showed what to do

Removed the storage bins. Removed the whole shelf, remove the glass part.(clean everything while you are at it, which is why it took 15-30 minutes) Lift out old rail and replace it with the new, reinstall shelf and glass. If you choose to not to clean, just take out the glass shelf, replace rail and put it back in. .

Unplugged appliance. Using a small putty knife I moved the switch out far enough to grab it with pliers. Moved wiring to new switch and pushed into place after testing.

This is the 2nd Jazz board that we replaced in 2 years. We believe that a power surge caused the board to no longer work. We now have the fridge plugged into a surge protector. The instruction sheet to program the jazz board did NOT come with this part. I called Parts Select and they gave me a number for Whirlpool. I spent over 30 mins. talking to Whirlpool, 2 different departments, and they do not have instructions for this part. I was told that they only supply instructions for about 10% of the parts that they distribute. I was able to find the instruction sheet on my own but searching "whirlpool instruction 16022940." I hope this helps!

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch

I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.

Easily ordered the part, arrived quickly, good price, just what we needed. Easy peasy install with a screwdriver. I'll shop here, again!

Thanks for the control board. However, it arrived in two days not overnight, UPS noted on their tracking site the error was their own. Also, the part did not come with installation instructions or programming instructions. Found on youtube a video that described in detail the programming procedure: . . . . . very helpful.

Thanks,
Marc

I initially thought the defrost heater or sensor were bad and replaced them. About a week later the problem reappeared. I ordered the control board assembly and after arrival I did the following: Went on-line, located the part on the fridge parts diagrams and figured out how to remove the controller cover (use two flat screwdrivers from behind). After the cover removal unplug the two connectors and lift out the sensor from its mount. Remove the LED Display/Button Board then the microcontroller board. They literally lift out. With the new controller you have to gently break the display board from the controller - the board is scribed along the break-away area. Do this on a flat surface. The actual board installation and hook-up took less than 5 minutes to reassemble. MAKE SURE THE REFRIGERATOR IS UMPLUGGED - I should have said that FIRST.

followed instructions given; simple fix!