1066697 Kenmore Refrigerator - Instructions

All Instructions for the 1066697
121 - 135 of 180

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
The refridgeror side was not cold enough
0 of 2 people found this instruction helpful.
  • Patrick from Sun City, AZ
  • Really Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
it was a simple repair once I located the part I had to replace . I really like your speedy delivery of the part I needed Thank you Pat Crotty
Was this helpful?
Thank you for voting!
noisey fan
0 of 4 people found this instruction helpful.
  • Richard from Morgan, UT
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
yup
Was this helpful?
Thank you for voting!
Switch was not working after a repairman had fixed something else
0 of 4 people found this instruction helpful.
  • Jackie from Nova, OH
  • Really Easy
  • Less than 15 mins
Please bear in mind I am 65 years old & it was harder to get up & down off the floor then to change the switch. Was very easy - watched video, unplugged unit. I used the putty knife at the right front corner to work loose, when it came loose had to loose the left side a little. The unit pulled out easily. detached the wired that had a single plug with 2 prongs on it. Attached the plug, pushed new switch into place. There was no way you could place wires on wrong prong. When done, plugged refrigerator back in & checked if working. I CAN SEE THE LIGHT and the food in the freezer now. Thank you for making an easy repair.
Was this helpful?
Thank you for voting!
light switch sticking
  • Paula from Rush, NY
  • Easy
  • Less than 15 mins
  • Pliers, Screw drivers
I watched the video and thought "I can do this". Made some notes and then proceeded to remove the old switch and replace with the new one. Thank you.
Was this helpful?
Thank you for voting!
Light did not come on (bad bulb!) on TC18KL
  • Louis from Beloit, WI
  • A Bit Difficult
  • Less than 15 mins
I have never before seen a bulb with the filament intact not light. If the bulb's filament seems intact, screw the bulb into a known working lamp and see if it lights. When screwing it back into the socket in the fridge, it takes a bit of extra effort to fully seat (until it does, it won't light!). For replacing the switch, I unplugged th e unit, used a paint scraper and worked it under the switch bezel from the right side. A bit of moxie, and the switch came out. The replacement switch had a different spade contact spacing than the original. I used a pair of scissors to cut the rubber bridge between the two switch wire connectors so I could connect to the new switch. In the end, it turned out to be the bulb. NOTE: The Model TC18KL is _not_ listed! What I finally found that the number "P7803211WL" on the sticker is actually a manufacturing code. Found this out by searching, and Sears' part search came up with matches.
Was this helpful?
Thank you for voting!
frosted evaperator
  • Burton from Mount ShaSTA, CA
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I was a Sears repair man for fourty eight years , so I don"t think I should say how easy this was.
Was this helpful?
Thank you for voting!
Evaporator Would Freeze Up And The Food Section Could'nt Cool
  • michael from buchanan, TN
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
I just followed the enclosed instructions
Was this helpful?
Thank you for voting!
Light switch went bad
  • Joseph T. from Morgantown, WV
  • Really Easy
  • Less than 15 mins
Simply stick a putty knife between the switch and refrig wall. Pop out old swith, remove both wires by pulling off switch by terminals. Throw switch out. Put wires on new switch and push into slot and all done. Nothing to it! Took me 5 minutes if th
Was this helpful?
Thank you for voting!
light would come on and off
  • Dora from Rock Island, IL
  • Really Easy
  • Less than 15 mins
Viewed the viedo - it showed what to do
Was this helpful?
Thank you for voting!
exchange of defective light rocker switch
  • Steve from River Edge, NJ
  • Really Easy
  • Less than 15 mins
  • Screw drivers
1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch
Was this helpful?
Thank you for voting!
The Refrigerator Was Running But Blowing Hot Air, Everything In Freezer Had Defrosted.
  • Jeanne from Fairview Heights, IL
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
First I watched the video on your website, it was quite helpful. It showed me the location of the part to be replaced. Then I used the nut driver to remove a couple of screws, and slowly pulled the cover off . Once I pulled the cover down I could see the part that needed replacing, it had a couple of phillips head screws holding it in place, I removed those screws and unplugged the defrost timer, taking note of the color of the wires. Then I took the new defrost timer and attached the loose wire to the correct terminal according to the directions(this is where the color of your wires comes in), then I plugged in the new defrost timer and replaced the screws. I then reattached the cover making sure not to pinch any of the wires, and replaced the screws. It was so easy I was sure I did something wrong and it wouldn't work, but I plugged the refrigerator back in and let it sit for about 20 minutes and then when I checked it was running cool. I'm 55 years old and never had the nerve to try anything like this before but since my husband passed away I've had to try things myself or replace a lot of appliances. If I can do it anyone can.
Was this helpful?
Thank you for voting!
Light in the refrigerator didn't work
  • Anthony from Fairport, NY
  • Really Easy
  • Less than 15 mins
  • Screw drivers
I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.
Was this helpful?
Thank you for voting!
Water was running into refrig from freezer and ice cream was soft
  • William from Delano, MN
  • Really Easy
  • Less than 15 mins
  • Nutdriver
We wasted time looking for the electrical schematic on our refrigerator (the first step in the instructions). By skipping that and reading further in the instructions, the type of cooling that the refrigerator has can easily be determined by the colors of the wires that go to the defrost timer. You need to know this to set up the timer properly for your specific refrigerator. Had I just started there, the entire repair would have taken less than 10 minutes. Very simple repair and it works like a charm, no more water coming into the refrigerator and the ice cream is rock hard. Glad we didn't have to spend lots on a new appliance. Thanks Part Select.com! BH
Was this helpful?
Thank you for voting!
condenser motor broke
  • patrick from livonia, MI
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
opened box,read directions,took out bad motor,installed new one.PRESTO CHANGO way to go.
Was this helpful?
Thank you for voting!
not makinig ice due to lack of water flow to maker
  • David from Manlius, NY
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Followedinstructions that came with kit. Kit parts were unnecessary as new valve fit in exactly as old one had been. Quick connect for flow out of valve to maker was a surprise as no threaded connection present and no nut necessary; simiply push the line into place. Reconnect water line, check for leaks and refasten back covering. Inst ructions with kit contained an incorrect drawing of connecting water outflowline; a one page addition verbally gave correct info, but detailed step by step instruction for this one connection was confusing. Otherwise, could not have been easier; surely a do-it-yourself project.
Was this helpful?
Thank you for voting!
All Instructions for the 1066697
121 - 135 of 180