- Home
- 1066695421
- Instructions
1066695421 Kenmore Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
The freezer compartment was not cold enough.
-
Tom from Paducah, KY
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I found the condenser fan was not working so I bought a new condenser fan kit and installed it. Fixed!
Was this helpful?
Thank you for voting!
Refrigerator was freezing everything
-
Robert from Norwich, CT
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
First of all the part was not located in the section of the refrigerator that was shown in the video. I wasted a lot of time taking that section apart only to find that the part wasn't there. After some investigation I finally located the defective part. It was behind a piece of sheet metal that had to be bent out of the way to unscrew
... Read more
the part. If I hadn't bent it out of the way, it would have been a major disassembly to remove the sheet metal. Once removed, the installation of the new part was fairly simple. The only confusing thing about the installation was determinig which of the prongs on the part that the internal wire to the new part was to be attached. There were 3 options given and the instructions were not very clear as to which one I should use. Apparently I guessed correctly because the refrigerator seems to be functioning perfectly since the repair.
Read less
Was this helpful?
Thank you for voting!
Ice on the botton of top freezer
-
Glenn from Capitol Heights, MD
- Easy
- 30 - 60 mins
-
Nutdriver
I just simply eliminated the ice buildup with hot water and a knife. But I still have the Defrost Timer Kit for future use.
Was this helpful?
Thank you for voting!
Frozen Lettuce In Crisper
-
Mary E. from Chicago, IL
- Really Easy
- 30 - 60 mins
-
Screw drivers, Socket set
My husband put in in, no problem and all is well. My husband is a mechanic for large machinery/motors so installation was no problem. Thanks, better than buying a new fridge!!!
Was this helpful?
Thank you for voting!
Freezer iced over, water leaking into refridgerator
-
Jennifer from Cincinnati, OH
- A Bit Difficult
- 30 - 60 mins
-
Nutdriver, Pliers
My fridge is a little different from the video model. The Controls in the fridge are located on an "arm" which swings down when the two screws are removed from the sides. It was not necessary to remove a front plate or knobs. However, I found when I got in to it that the old timer was not held by screws, but by plstic posts which had thes
... Read more
e "speed nuts" on them. This is a little metal plate which fits over the plastic post and bends to lock it in place. When you try to remove it, it acts like a barb, holding the little sucker on. I ended up bending the ends of those little suckers up tight against the post and twisting and pulling with needle-nose pliers. I broke one post like others before me commented, but one stayed intact. The only break at the top, so there ie still post left to hold the new timer. Once it was off, I was able to replace easily. The directions for choosing the right prong were a little confusing, but follow your gut and go with the wire colors. My schematic found in the bottom of the fridge did not look like any of the drawings, but I could match the wire colors. I also asked "Just Ask" for help, to make sure. My gut instinct was right. My fridge is now working again beautifully. If a housewife with no appliance repair knowledge can do it, so can you. I fixed my dryer with PartSelect too!I will never call another repair man until I have checked this site to see if I can do it myself. Bet I have saved $600 so far at least!
Read less
Was this helpful?
Thank you for voting!
Refregirator would not freeze properly. It would stay in the defrost mode at times.
-
Eartis from Mckenzie, AL
- Easy
- 30 - 60 mins
-
Nutdriver, Pliers, Screw drivers
I did the repair just as your video showed me. It worked out great.
Was this helpful?
Thank you for voting!
part not like old part
-
Lawrence from Pottstown, PA
- Difficult
- 30 - 60 mins
-
Screw drivers
The part could not be installed without home made angles which were attached to unit so that it would only protrude from back of refrigerator about 2" instead of 6".
Was this helpful?
Thank you for voting!
not cooling could hear a clicking noise
-
Deborah from Elkton, MD
- Easy
- 30 - 60 mins
-
Screw drivers, Socket set
With the help of the website I was able to verify that the part I removed (in the area of the clicking sound) was probably the part required for replacement. I ordered it, installed it... IT WORKS (I knew it the moment I plugged in the power cord and heard the compressor kick on). Saved me from buying a new fridge or calling a repairman.
... Read more
I'm a 58 year old woman with no appliance experience. I watched the videos and installed the part without any trouble. Thank you PartSelect for your easy to use website instructions and helpful hints.
Read less
Was this helpful?
Thank you for voting!
condenser fan wore out
-
Nancy from Gallatin, TN
- Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
The kit I recieved was perfect. All parts fit and where a perfect match. I will give you an A+ in handling my order and shocked by speed of your delivery.
Was this helpful?
Thank you for voting!
Freezer not cooling. Temperature rising.
-
Jeff from Austin, TX
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
One day the ice cream in the freezer seemed mushy, but the ice was still frozen. There was not water in the ice bin. However, the problem resolved itself. This suggested that the defrost timer had become stuck for an extended time, but then continued to run. The fact that the freezer went back to frozen, implies that all the component
... Read more
s of the cooling loop (compressor, condenser & fan, evaporator & fan) were fine. It was possible that the problem was caused by a bad defrost (?evaporator?) thermostat but everything I saw on line suggested that the defrost timer is the culprit about 40 - 50% of the time. Anyway, I followed the instructions in the on-line video at this site for replacing the defrost timer and it was easy. It would have only taken 15 minutes, but I spent a while reading the defrost timer instructions and hunting down a schematic for my refrigerator, to determine which pin the loose wire should go on.
Read less
Was this helpful?
Thank you for voting!
New Part Was Different From Previous Part
-
Robert from Metuchen, NJ
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
First attempt was difficult. Part was different and instructions applied to previous part that did not have quick connect. Not clear where quick connect was to be used. Result no ice!second attempt used quick connect in reverse connections and now have plenty of ice. Combination of change in part appearence from previous one ,and diff
... Read more
erent from instructions included with new part, resulted in confusion in installation. In the long run, it worked out well.
Read less
Was this helpful?
Thank you for voting!
Fan was making noise, Freezer temperature was erratic
-
Dik from Quincy, MA
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Screw drivers
First, watched video on Part Select Website. Very good. Pulled Appliance out from wall, Pulled the power plug, and removed the back shield covering the working parts of the unit. Found the fan and it was almost the same setup as on the video except that I could not get to one of the screws holding the motor in place so had to remove t
... Read more
he entire bracket with the fan. Not too hard. Cleaned away dust and gunk around the site and noticed that the fan pulled air through a tunnel-like condenser coil that was packed with gunky lint...this is what probably killed the motor. I cleaned out the tunnel with the bottle brushes and vacuum and installed the new motor / bracket assembly. Then replaced the shielding around the fan and the back cover .panel. This is important because these form the channel that guides air flow throughout the condenser coils. This particular refrigerator has a barrier underneath which guides air flow from the front left to the condenser, through the fan, over the evaporator drip pan and out the right front. I cleaned all the lint and gunk from this area as well. I also made an air filter (cut from a furnace filter) and wedged it in front of the air entry section. This should keep the condenser coil cleaner over time but you have to remember to change the filter once a year. Probably should clean the condenser coil every 5 years as well. This unit has been very reliable over 20 years and may well go for another 20. Good luck with your repair.
Read less
Was this helpful?
Thank you for voting!
Fan motor worn out
-
Myrna from Decatur, IL
- Difficult
- 1- 2 hours
My Son who is not an appliance repairman did it for me. He had some difficulty getting the nuts and bolts loose mainly. Sorry I'm not much help other than that! I would like to compliment you on your fast service, first time ordering from you and it was for an older model refrigerator that my repairman said he couldn't find. It's
... Read more
working fine now and I'm a satisfied customer!
Read less
Was this helpful?
Thank you for voting!
wouldn't make ice, door seal was hot to touch, warm in fridge.
-
Dale from Sterling, AK
- A Bit Difficult
- 1- 2 hours
-
Nutdriver, Socket set
I folded in half twice! and took the back off the fridge(cardboard) and took one brace off and just took the screws off the fan from the other two braces. Turned the fan enough to get at the wires for the fan and cut them off an inch from the old fan, stripped the insulation and wire nutted them to new fan. Make sure they don't interfere
... Read more
with the new fan and put the new fan in place put the screws in and we're making ice and cold fridge again.
Read less
Was this helpful?
Thank you for voting!
Refrig ran and ran with a lot of hot air coming from the back. Temps in freezer and refrig areas would fluctuate with the unit running almost constantly. Discovered the fan was intermittently running, mostly not.
-
Donald from Strafford, NH
- Easy
- 1- 2 hours
-
Socket set
Removed the old fan; cut the wire and spliced in the new fan and reassembled. A little over one hour. Refrig is working perfectly now with lower settings. It is definitely off much more than on now.
Was this helpful?
Thank you for voting!